• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.683-688
• /
• 1999

The purpose of this study is to develop and evaluate the structural performance of various shear walls, such as the hysteretic behavior, the maximum horizontal strength, crack propagation, and ductility etc. under load reversals. For the diagonal reinforced slit and infilled shear wall specimens, it was found that the failure mode shows very effective crack control and crashing due to slippage prevention of boundary region and reduction of diagonal tension rather than the brittle shear and diagonal tension failure. The ductility of specimens designed by the diagonal reinforcement for the slit and infilled shear wall was increased 1.72~1.81 times in comparison with the fully rigid shear wall frame. Maximum horizontal load-carrying capacity of specimens designed by the diagonal reinforcement ratio the slit and infilled shear wall was increased respectively by 1.14 times and 1.49 times in comparison with the standard fully rigid shear wall frame.

• Architectural research
• /
• 제19권4호
• /
• pp.117-124
• /
• 2017

In this research, we carried out finite element analysis depends on the variations such as the strength of the main bar, concrete, shear-span ratio(a/d) and existence of shear reinforcing bar. Throughout the results of FEM analysis, we were able to figure out how each variation can effect on shear performance. As the strength of concrete increased, the maximum shear force enhancement effect of each specimen was evaluated. As a result, the shear strengthening effect was 51~97% for shear reinforced specimens, and 26~44% for non-shear reinforced specimens. As the yield strength of reinforcing bars increases, the shear reinforcement effect of the specimen the specimens without shear reinforcement were 3%~6% higher than those with shear reinforcement. Theoretical and analytical values were compared using the design equations obtained from the CEB code. Theoretical and analytical values were compared using the design equations obtained from the CEB code. As a result, the error rate was the highest at 3.64 in the S1.0-C0 series and the lowest at 1.46 in the S1.7-C1 series. Therefore, the design equation of the CEB code is estimated to underestimate the actual shear strength of deep beams that are not subjected to shear reinforcement.

• Computers and Concrete
• /
• 제20권6호
• /
• pp.731-738
• /
• 2017

Reinforced concrete flat plates consist of slabs supported directly on columns. The absence of beams makes these systems attractive due to advantages such as economical formwork, shorter construction time, less total building height with more clear space and architectural flexibility. Punching shear failure is usually the governing failure mode of flat plate structures. Punching failure is brittle in nature which induces more vulnerability to this type of structure. To analyze the flat plate behavior under punching shear, twelve finite element models of flat plate on a column with different parameters have been developed and verified with experimental results. The maximum range of variation of punching stress, obtained numerically, is within 10% of the experimental results. Additional finite element models have been developed to analyze the influence of integrity reinforcement, clear cover and column reinforcement. Variation of clear cover influences the punching capacity of flat plate. Proposed finite element model can be a substitute to mechanical model to understand the influence of clear cover. Variation of slab thickness along with column reinforcement has noteworthy impact on punching capacity. From the study it has been noted that integrity reinforcement can increase the punching capacity as much as 19 percent in terms of force and 101 percent in terms of deformation.

• 한국전산구조공학회논문집
• /
• 제27권5호
• /
• pp.413-420
• /
• 2014

본 논문에서는 유공형 형상의 GFRP 판으로 전단 보강된 플랫 플레이트의 전단거동을 실험을 통해 평가하였다. GFRP 판은 개구부가 있는 판의 형태로서 콘크리트와의 일체화 거동을 위하여 콘크리트에 매립하여 시공하였다. GFRP 판으로 전단 보강된 플랫 플레이트의 전단 성능 실험을 위하여 총 7개의 시험체에 대한 전단 실험을 수행하였다. 실험 변수로는 전단 보강량, 전단 보강 간격을 선정하였다. GFRP 판의 전단 보강량에 따른 비교결과, 전단 보강량이 증가할수록 전단강도도 증가하는 결과를 보여주었다. GFRP 전단 보강 간격에 따른 비교결과, 전단 보강 간격이 0.3d 일 때 가장 높은 전단강도를 확인하였다. 실험결과를 바탕으로 KCI에서 제시하고 있는 전단강도식을 수정하여 GFRP 판에 적용이 가능한지 평가하였다.

• Structural Engineering and Mechanics
• /
• 제38권3호
• /
• pp.361-384
• /
• 2011

Earlier studies on hollow-circular rubber bearings, all of which are conducted for steel-reinforced bearings, indicate that the hole presence not only decreases the compression modulus of the bearing but also increases the maximum shear strain developing in the bearing due to compression, both of which are basic design parameters also for fiber-reinforced rubber bearings. This paper presents analytical solutions to the compression problem of hollow-circular fiber-reinforced rubber bearings. The problem is handled using the most-recent formulation of the "pressure method". The analytical solutions are, then, used to investigate the effects of reinforcement flexibility and hole presence on bearing's compression modulus and maximum shear strain in the bearing in view of four key parameters: (i) reinforcement extensibility, (ii) hole size, (iii) bearing's shape factor and (iv) rubber compressibility. It is shown that the compression stiffness of a hollow-circular fiber-reinforced bearing may decrease considerably as reinforcement flexibility and/or hole size increases particularly if the shape factor of the bearing is high and rubber compressibility is not negligible. Numerical studies also show that the existence of even a very small hole can increase the maximum shear strain in the bearing significantly, which has to be considered in the design of such annular bearings.

• 한국지진공학회논문집
• /
• 제20권6호
• /
• pp.361-368
• /
• 2016

Coupling beams serve as primary source of energy dissipation in coupled shear wall systems during large earthquakes. However, the overestimation of the shear strength of diagonally reinforced coupling beams may be adverse effect on the seismic performance of coupled shear wall systems. In order to force coupling beams to properly work during earthquakes, coupling beams should be designed with accurate shear strength equations. The objective of this study is to propose the accurate shear strength equation for slender diagonally reinforced coupling beams. For this purpose, experimental tests were conducted using three diagonally reinforced coupling specimens with different amount of transverse reinforcement under reversed cyclic loads to evaluate the hysteretic behavior of the specimens. The test results show that transverse reinforcement of slender diagonally reinforced coupling beam affects the maximum strength and drift ratio.

• 국제강구조저널
• /
• 제18권4호
• /
• pp.1420-1430
• /
• 2018

Earthquakes of 5.8 and 5.4 Richter scale recently occurred one after another in Korea, changing the Korean peninsula from an earthquake safe zone but 'earthquake danger zone'. Therefore, seismic reinforcements must expand to include structures with low seismic resistance in order to prepare for earthquakes on a larger scale in the future. This study investigated the performances of various seismic reinforcement systems such as X-braced steel rod reinforcement, steel shear wall with circular opening reinforcement, and slit damper reinforcement using shaking table test and computational analyses of seismic data in order to establish a proper seismic reinforcement plan. These three seismic reinforcement systems could increase the stiffness and strength of existing structures and reduce maximum drift ratio in the event of an earthquake.

• 한국지반공학회논문집
• /
• 제19권2호
• /
• pp.189-197
• /
• 2003

본 논문은 공진주시험과 삼축압축시험을 이용하여 소변형률(0.0001%~l%) 범위에서 섬유혼합토의 변형 특성을 규명하였으며, 최대전단탄성계수를 잣대로 보강효과를 평가하였다. 또한 단섬유의 직경에 대한 길이의 비(형상비), 흙의 중량에 대한 섬유 중량의 섬유혼합비, 단섬유의 종류에 따른 보강효과를 비교 검토하였다. 시료는 주문진 표준사에 폴리프로필렌 재질의 단섬유를 무작위로 배합하여 사용하였다. 섬유혼합토의 최대전단탄성계수는 비혼합토에 비해 최대 30%까지 증가하였고, 비선형 영역에서의 전단탄성계수 감소량도 억제되었다. 형상비가 증가할수록 최대전단 탄성계수는 증가하고, 단사에 비해 망사의 보강 효과가 큰 것으로 나타났다. 섬유혼합비는 0.3 % 부근에서 보강효과가 가장 커, 최적인 것으로 확인되었다.

• 콘크리트학회논문집
• /
• 제24권4호
• /
• pp.407-414
• /
• 2012

이 연구의 목적은 매립형 유공 GFRP(glass fiber reinforced polymer) 판으로 보강된 철근콘크리트 보의 전단 거동에 관하여 실험적으로 연구하였다. 보강재의 형상, 보강면적, 보강재 두께 및 폭의 영향을 변수로 선정하였다. 전단 경간비가 2.8인 일반보 총 9개의 시험체에 대한 전단실험을 수행하였다. GFRP 판이 철근 스터럽으로 보강한 경우보다 단위보강면적당 전단강도가 3.6배 향상되었다. 보강면적에 따른 전단성능을 평가한 결과 전단보강면적이 증가함에 따라 전단강도도 증가하였다. 보강재의 형상에 따라 전단성능의 영향을 평가한 결과 평행사변형 GFRP 판이 기본격자형 GFRP 판보다 전단강도가 우수한 것으로 나타났다. 일정한 보강면적에서 보강재의 폭 및 두께를 변수로 두었을 때 폭이 증가할수록 전단성능이 향상되는 것을 확인할 수 있었다. 결과적으로, GFRP 판으로 전단 보강된 철근콘크리트 보의 ACI 318M-08 기준식에 의한 최대전단강도와 실험에 의한 최대전단강도를 비교하였다. 또한, ACI 318M-08, CSA-04, EC2-02 기준식의 최대전단보강면적과 시험체의 최대전단보강면적을 비교하였다.

• 한국전산구조공학회논문집
• /
• 제20권6호
• /
• pp.699-708
• /
• 2007

일반적으로 깊은 보의 개구부 보강을 할 경우 개구부 주변의 부족한 내력에 대해 수직, 수평, 대각, 혹은 혼합된 배근 형태를 사용하게 되는데, 경제성과 구조적 안전성을 고려하기 위해서는 각 배근 형태 및 방법에 따른 깊은 보의 거론 평가와 적절한 조합에 관한 연구가 절실히 필요하다. 이에 본 연구에서는 개구부 보강방법을 변수로 한 simulation 모델을 통해 수직, 수평 보강의 효과에 대해 해석적으로 검증을 한 후, 각 규준에서 제시하고 있는 개구부가 있는 깊은 보의 전단 내력식을 분석하고 해당 식을 보완하여 단순지지 1경간 및 연속 경간에 적용 가능한 전단 내력 산정식을 제안하고자 한다.