• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.341-348
• /
• 2003

Photovoltaic systems normally use a maximum power point tracking (MPPT) technique ta continuously deliver the highest possible power to the load when variations in the insolation and temperature occur. A simple method of tracking the maximum power points (MPPs) and forcing the boost converter system to operate close to these points is presented through deriving small-signal model and transfer function of boost converter. This paper aims at modeling boost converter including equivalent series resistance of input reservoir capacitor by state-space-averaging method and PWM switch model with properly designed controller for maximum photovoltaic power tracking control.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.286-293
• /
• 2002

Photovoltaic systems normally use a maximum power point tracking (MPPT) technique to continuously deliver the highest possible power to the load when variations in the insolation and temperature occur. A simple method of tracking the maximum power points (MPPs) and forcing the boost converter system to operate close to these Points is presented through deriving small-signal model and transfer function of boost converter. This paper aims at modeling boost converter including equivalent series resistance of input reservoir capacitor by state-space-averaging method and PWM switch model. In the future, properly designed controller for compensation will be constructed in real system for maximum photovoltaic power tracking control.

• 대한전자공학회논문지SD
• /
• 제45권4호
• /
• pp.146-153
• /
• 2008

High speed serial link에 적합한 clock multiphase generator용 integrated phase-locked loop (PLL)을 설계하였다. 설계된 PLL은 programmable current mirror를 사용하여 동작 범위 안에서 동일한 loop bandwidth와 damping factor를 가진다. 또한 설계한 PLL 회로 netlists를 가지고 HSPICE 시뮬레이션을 통해 close-loop transfer function과 VCO의 phase noise transfer function을 구하였다. Board 위 칩의 자체 임피던스는 decoupling capacitor의 크기와 위치에 따라 계산된다. 세부적으로, close-loop transfer function에서 gain의 최대값과 VCO noise transfer function에서 gain의 최대값 사이의 주파수범위에서 decoupling capacitor의 크기와 위치에 따른 보드 위 칩의 자체 임피던스를 구하였다. 이를 바탕으로 보드에서의 decoupling capacitor의 크기와 위치가 PLL의 jitter에 어떠한 영향을 미치는지 분석하였다. 설계된 PLL은 1.8V의 동작 전압에서 400MHz에서 2GH의 wide operation range를 가지며 $0.18-{\mu}m$ EMOS공정으로 설계하였다. Reference clock은 100MHz이며 전체 PLL power consumption은 1.2GHz에서 17.28 mW이다.

• 전기학회논문지
• /
• 제60권3호
• /
• pp.560-565
• /
• 2011

This paper proposes the design of micro energy harvesting system by using thermoplastic polyurethane(TPU), which harvests electric energy from the kinetic energy of pedestrian and drives the desired load, and applied it to the self-generating shoes. Also, we designed the buck-boost converter in discontinuous conduction mode(DCM) which functions as a resistor emulator(RE) such that converter's average input current is proportional to input voltage, and it results in transfer of maximum power to buck-boost converter according to control behavior that converter's input resistance is matched with TPU's internal resistance. Therefore, this paper confirms the validity of proposed control scheme and possibility of application for self-generating shoes, from the obtained characteristic of designed micro energy harvesting system by using a TPU and buck-boost converter in DCM.

• 전기학회논문지P
• /
• 제63권2호
• /
• pp.113-118
• /
• 2014

Tidal power is one of new and renewable energy sources. Tidal power is generated by using the gap in the water level between the water outside and inside the embankment. All tidal power plant in Korea were being operated by import of turn-key from abroad. The know-how and technology which are the most important to build predictive control system has become increasingly difficult to obtain from advanced countries because most of them avoid to transfer, which the domestic development of the control system is needed. In this paper, a study on start stop system at water turbine-generator for tidal power plant at the beginning of development was presented. For improvement the efficiency and develope of core technology of the start stop system, the technique and characteristics of tidal power, modeling, maximum generation calculation method, and optimal control of joint control system in Sihwa tidal power plant were studied.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 A
• /
• pp.360-362
• /
• 2000

This paper presents a probabilistic method for describing the transfer capability of one area in an interconnected power system. The approach is based on Monte Carlo simulation scheme. The result of this method is the probability distribution of transfer capability. The distribution yield a general framework for probabilistic analysis of STC. IEEE RTS-24 power system is utilized to evaluate the proposed method.

• 설비공학논문집
• /
• 제5권4호
• /
• pp.265-277
• /
• 1993

Recently, underground transmission system is growing continuously according to the electric power demand increase in the downtown area. Even if domestic cable makers are manufacturing 154kV oil filled cable and joint, the design technology of cable-joint has not been fully self-reliance. This study is aimed at the detail heat transfer analysis of 154kV cable-joint. So, that is cut into the five sections in order to analyze a conjugate natural convection in two dimensional $r-{\theta}$ coordinate. The streamline and temperature distributions are obtained for each sections. Also the changes of those are analyzed with respect to the variation of transmission currents and cable-joint surface heat transfer coefficients. The same analyses are also shown in view point of the maximum temperature of conductor and local equivalent conductivity.

• International journal of advanced smart convergence
• /
• 제1권2호
• /
• pp.16-19
• /
• 2012

A modified 4-coil magnetic resonance wireless power transfer (MRWPT) system is proposed. Four coils based on 2-coil system with additional two matching coils were used in this topology. When Tx-Rx distance is changed, the input impedance is changed. However, it can be adjusted by coil parameters of matching coils to maintain impedance matching for maximum efficiency. The equivalent circuit of MRWPT system was analyzed for both transmission function and optimum coupling coefficient of the matching coils. By using four spiral resonant coils, these design considerations was experimentally verified. The measured data agreed well with the calculated data and the transmission function of the proposed system was more efficient than that of conventional 2-coil system.

• 한국표면공학회지
• /
• 제41권6호
• /
• pp.274-278
• /
• 2008

3-dimensional numerical analysis for a rectangular magnetron cathode model is done to predict cooling characteristics of high power sputtering system for ZnO deposition. It includes cooling channel design, heat transfer analysis of a target, bonding layer and backing plate. In order to model erosion profiles of a target, ion current density distribution from 3D Monte Carlo simulation is used to distribute total sputtering power to 5 discrete regions. At 3 kW of sputtering power and cooling water flow of 1 liter/min at $10^{\circ}C$, the maximum surface temperature was $45.8^{\circ}C$ for a flat new target and $156^{\circ}C$ for a target eroded by 1/3 of its thickness, respectively.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 춘계학술대회 논문집
• /
• pp.447-450
• /
• 2004

This paper presents the basic application idea of superconductor cable for voltage stability limited power system. In bulk power system, the transfer capability of transmission line is often limited by the voltage stability, and superconductor cable could be on of the countermeasure to enhance heat transfer limit as well as voltage stability limit. Steady state voltage stability approach by P-V curve is used to calculate the maximum transfer capability of initial system and superconductor applied system IEEE-14 bus system is used to demonstrate its applicability.