• 한국입자에어로졸학회지
• /
• 제9권3호
• /
• pp.139-147
• /
• 2013

The performances of indoor air cleaners including particle cleaning capacity and collection efficiency are usually tested at the condition of the maximum air flow rate of the air cleaners. However, the power consumption of the air cleaners is highly dependent on the air flow rate of the individual air cleaners. Therefore, there seems to be an optimized air flow rate for the air cleaning capacity considering power consumption. In this study, clean air delivery rate(or standard useful area as suggested room size) and power consumption have been investigated for different maximum air flow rates of 15 air cleaners and then compared those for different air flow rate modes of the individual 5 air cleaners selected from the 15 cleaners. For the maximum air flow rate conditions of 15 air cleansers, the power consumption per unit area was less related to the maximum air flow rate. However, for the different air flow rate modes of the selected 5 air cleaners, the lower power consumption per unit area was corresponding to the lower air flow rate mode of the individual air cleaners. When considering the operation time to the desired particle concentrations, there was an optimized one in the medium air flow rate modes for the individual air cleaners. Therefore, not only the maximum air flow rate but also lower air flow rates of individual air cleaners should be considered for estimating air cleaning capacity based on energy consumption per unit area.

• 태양에너지
• /
• 제4권2호
• /
• pp.13-28
• /
• 1984

Direct Absorption Receiver and Thermal Storage System is a complex problem. This paper describes only characteristic of fluid flow on the receiver. The fluid thicknesses of Molten Salts (Melting Point : $397^{\circ}C$) flowing on the receiver of modified protopype ($10m{\times}10m$) were calculated theorectically, changing the receiver slope from 60 degree to 85 degree (5 steps). The receiver temperatures were $430^{\circ}C$ at the top part and $950^{\circ}C$ at the low part. The flow thickness of the Molten Salts at the top part of the receiver are around 1.9mm in the case of maximum insolution ($50{\times}10^6$juoule/sec; 58.898kg/sec of flow rate) and 2.0mm at the low part. In the case of 3/10 of maximum insolation (flow rate = 17.669kg/sec) the flow thickness at the top part are around 0.9mm and 0.4mm at the low part, and in the case of 1/10 of maximum insolation (flow rate = 5.889 kg/see) the flow thickness at the top part are around 0.6mm and 0.3mm at the low part. From experimental measurements of a normal fresh water thickness flowing on the model plate ($12.7cm{\times}111.76cm$), around 0.8mm at the top part of the plate and around 0.7mm at the low part were obtained in the case of maximum insolation (flow rate = 0.12496 kg/see). In the case of 3/10 (flow rate = 0.03748 kg/see) and 1/10 (flow rate = 0.012496 kg/see) of maximum insolation, around 0.5mm and 0.4mm at the top part, and around 0.3mm and 0.2mm at the low part were obtained respectively. The reason why the thickness of the Molten Salts increase at the low part of the receiver only in case of maximum insolation is that decreasing rate of the viscosity of the Molten Salts is larger than decreasing rate of the density of the Molten Salts during temperature increase from the top to the low receiver plate and decrease of the fluid velocity in accordance with continuity principle. In all cases without the above maximum insolation, the thickness of the Molten Salts and the fresh water decreased at the low part of the plate because of gravity force effects rather than friction effects and of continuity principle. All simillar flow patterns were obtained through all cases of the insolation making an exception of only maximum insolation.

• 한국기계가공학회지
• /
• 제19권2호
• /
• pp.18-23
• /
• 2020

The maximum speed and pressure distribution close to a warhead are altered based on the warhead shape, thereby resulting in changes to the flight distance and the destructive power. In this study, flow analysis was carried out based on the warhead shell shape. The maximum flow rate was detected at the side of shell, with a lower flow rate being found at the rear of the shell. In addition, the maximum pressure was detected at the warhead. It was also found that the reduction in the flow rate between the rear and the side of the shell in model A was smaller than that in model B. The obtained results are expected to be useful in the future design of shell warhead shape.

• 대한기계학회논문집
• /
• 제17권9호
• /
• pp.2381-2389
• /
• 1993

In this paper the design and test results of a dynamic flow rate sensor was reported. This sensor comprises an 2-way cartridge valve as standard hydraulic component and a displacement sensor. Its working principle bases on the linear relationship between the flow rate and the piston displacement of 2-way cartridge valves under constant pressure drop. This principle is well known, however it is not easy to develop a flow rate sensor with the measurement range of 300 1/min, pressure loss of less than 8 bar at 300 1/min, maximum linearity error of less than $\pm$1% and the maximum rising time of 10 ms. This paper describes the design procedure of the flow rate sensor, the improvement procedure of static performance and test method and results of dynamic performance.

• 설비공학논문집
• /
• 제18권5호
• /
• pp.410-417
• /
• 2006

The present study predicted the effect of the flow rate of coolant on the absorption performance of a vertical falling film type absorber Heat and mass transfer peformances were numerically investigated. The exit temperatures of solution and coolant were decreased as the flow rate of the coolant was increased at the film Reynolds number of 100. The absorption mass flux was increased and then decreased as the distance from the inlet of the absorber was increased. The distance showing the maximum absorption mass flux was ranged from 0.3 to 0.5m. The heat flux and the absorption mass flux were increased and then slowly decreased as the flow rate of the coolant was increased. The maximum values were obtained at the flow rate of coolant of 2.0L/min.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.34-38
• /
• 2018

Recently, the turbo charger has become an important part because it yields little displacement and high power while downsizing the engine's fuel ratio for environmental purposes. In this study, flow analysis was conducted to form the basis of data regarding the best efficiency. The axial displacement was changed from none to 25 mm by controlling the configuration of the turbo charger and the flow analyses were compared with each other. The maximum rate of the outlet of model 1 was 46.36 m/s and the maximum pressure of model 4 was 0.761946 Pa. The maximum flow rate of model 4 was 0.000187650 kg/s. This study's result should aid in the effective design of a turbo charger with high performance.

• 설비공학논문집
• /
• 제17권11호
• /
• pp.1035-1042
• /
• 2005

In the present study, the principle of minimum energy is employed to configure the shape of rivulet flowing down an inclined surface. The profile of laminar rivulet is determined by numerical integration. The maximum center thickness, which corresponds to the minimum thickness of falling film, is found to exist regardless of liquid flow rate and is compared with the analytical and experimental data. At small liquid flow rate the center thickness of rivulet and its width increase almost linearly with flow rate. Once the center thickness of rivulet becomes very close to its maximum value, its growth rate retards abruptly. However the width of rivulet increases proportionally to the liquid flow rate and most part of its free surface is as flat as that of stable film. The growth rate of rivulet thickness with respect to liquid flow rate becomes larger at bigger contact angle. The width of rivulet increases rapidly with its flow rate especially at small contact angle, As the liquid-vapor interfacial shear stress increases, the center thickness of rivulet decreases with its flow rate, which is remarkable at small contact angle. However the effect of interfacial shear stress on the width of rivulet is almost negligible.

• Nuclear Engineering and Technology
• /
• 제13권3호
• /
• pp.121-129
• /
• 1981

많은 기존 공식중 세계의 가장 우수한 최대 유량공식을 찾아, 그 세개의 한계유량공식의 개요와, 냉각재상실사고시 격납용기격리에 실패하는 경우를 특정지을 수 있는 구멍의 크기와 격납용기의 압력 및 온도 등이 주어진 상태하에서 격납용기로부터 외부대기로 방출되는 개략적인 핵분열생성물의 양을 추정하기 위한 계산절차를 제시하였다. 이상기체의 임계유량공식과 이상유(two-phase flow)의 최대유량을 산출하기 위한 무디(Moody)의 도표를 이용하여 계산실예를 제시하였으며, 그 결과를 콘뎀프트-앨티(CONTEMPT-LT) 전산코드의 질량유출공식을 콘버징 노즐(converging nozzle)을 통과하는 음속류(sonic flow)의 경우에 적용하여 산출한 값과 비교하여 보았다. 이리하여 이상 기체의 임계유량공식은 무디(Moody)의 공식이 주는 값과 거의 비슷한 결과를 줌을 입증하였다. 또한 냉각재상실 사고시 격납용기로부터의 유출율을 추정하기 위해서는 콘템프트-앨티(CONTEMPT-LT)의 질량유출공식을 사용하는 것보다 이상 기체의 최대유량공식을 사용하는 것이 더 보수적인 방법임을 보여 주었다.

• 대한기계학회논문집B
• /
• 제40권12호
• /
• pp.777-784
• /
• 2016

바나듐 전해질 산화-환원 흐름전지(vanadium redox flow batteries, VRFBs)는 간헐적 에너지 저장 시스템의 에너지 저장장치로 사용된다. VRFBs는 재료 및 동작조건에 따라 성능의 차이를 보이며, 각 성능특성에 따른 VRFBs개발이 요구된다. 본 연구에 사용된 단위셀은 반응면적 $25cm^2$이며, 전해액은 0.6의 충전상태를 나타낸다. 방전전류밀도를 0에서 $520mA/cm^2$ 까지 변화시키면서 동시에 전해질 유량도 5mL/min에서 60mL/min까지 변화시켰다. 동일한 입구 전해액 상태에 따른 방전 성능 평가를 위해 4개의 탱크를 사용한 비순환 시스템을 구축하였다. 본 논문은 유량 및 전류밀도의 변화에 대한 단자전압을 측정하였으며, $25cm^2$ 반응면적을 가지는 바나듐계 산화-환원 유동전지 시스템의 최대전류밀도에 대한 실험식을 도출하였다.

• 한국국방경영분석학회지
• /
• 제25권2호
• /
• pp.106-116
• /
• 1999

The purpose of this study is to present a method for determining the k most vital arcs in the maximum flow problem using genetic algorithms. Generally, the problem which determine the k most vital arcs in maximum flow problem has known as NP-hard. Therefore, in this study we propose a method for determining all the k most vital arcs in maximum flow problem using genetic algorithms. First, we propose a genetic algorithm to find the k most vital arcs removed at the same time and then present the expression and determination method of individuals compatible with the characteristics of the problem, and specify the genetic parameter values of constitution, population size, crossover rate, mutation rate and etc. of the initial population which makes detecting efficiency better. Finally, using the proposed algorithms, we analyzed the performance of searching optimal solution through computer experiment. The proposed algorithms found all alternatives within shorter time than other heuristic methods. The method presented in this study can determine all the alternatives when there exists other alternative solutions.