• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.49 no.6
• /
• pp.743-749
• /
• 2016

We compared two different processing methods for preparing high quality frozen in-shell baby clam products. In the first method, sand and mud were removed from the clams, then they were vacuum packed in polyethylene film, boiled at $97^{\circ}C$ for 6 min, and snap frozen in a cold air blast freezer (sample 1). The second processing method was similar, except the boiling process was excluded (sample 2). Both frozen products were boiled for 4 min, and then shucked and minced. Various quality metrics, such as the opening rates of shells, chemical composition, pH, volatile basic nitrogen (VBN), salinity, thiobarbituric acid (TBA), amino-N, total amino acids and free amino acids were measured, and sensory evaluation was conducted. The opening rates of shells of sample 1 and sample 2 were 98.3% and 4.67%, respectively. The proximate composition of sample 1 and sample 2 was 75.2% and 78.7% moisture, 19.7% and 16.2% crude protein, 2.45 and 2.2% crude lipid, 2.8% and 2.1% ash, and 2.1% and 1.9% salinity, respectively. The L, a, b and ${\Delta}E$ values were similar: 48.6 and 49.2, 3.9 and 3.9, 15.7 and 15.5, and 50.7 and 50.1 for sample 1 and sample 2, respectively. The sensory evaluation score of sample 1 was higher than that of sample 2. Sample 1 was deemed to be superior to sample 2; therefore, we determined that the boiling process is needed for manufacturing high-quality frozen clam products.

• Composites Research
• /
• v.28 no.4
• /
• pp.155-161
• /
• 2015

A composite structure was fabricated with embedded impact detection capabilities for applications in Structural Health Monitoring (SHM). By embedding sensor functionality in the composite, the structure can successfully perform impact localization in real time. Smart resin, composed of $Pb(Ni_{1/3}Nb_{2/3})O_3-Pb(Zr,\;Ti)O_2$ (PNN-PZT) powder and epoxy resin with 1:30 wt%, was used instead of conventional epoxy resin in order to activate the sensor function in the composite structure. The embedded impact sensor in the composite was fabricated using Hand Lay-up and Vacuum Assisted Resin Transfer Molding(VARTM) methods to inject the smart resin into the glass-fiber fabric. The electrodes were fabricated using silver paste on both the upper and bottom sides of the specimen, then poling treatment was conducted to activate the sensor function using a high voltage amplifier at 4 kV/mm for 30 min at room temperature. The composite's piezoelectric sensitivity was measured to be 35.13 mV/N by comparing the impact force signals from an impact hammer with the corresponding output voltage from the sensor. Because impact sensor functionality was successfully embedded in the composite structure, various applications of this technique in the SHM industry are anticipated. In particular, impact localization on large-scale composite structures with complex geometries is feasible using this composite embedded impact sensor.

• The Journal of Advanced Prosthodontics
• /
• v.1 no.2
• /
• pp.63-67
• /
• 2009

STATEMENT OF PROBLEM. Use of custom tray and tray adhesive is clinically recommended for elastomeric impression material. However there is not clear mention of drying time of tray adhesive in achieving appropriate bonding strength of tray material and impression material. PURPOSE. This study is to investigate an appropriate drying time of tray adhesives by evaluating tensile bonding strength between two types of polyvinylsiloxane impression materials and resin tray, according to various drying time intervals of tray adhesives, and with different manufacturing company combination of impression material and tray adhesive. MATERIAL AND METHODS. Adhesives used in this study were Silfix (Dentsply Caulk, Milford, Del, USA) and VPS Tray Adhesive (3M ESPE, Seefeld, Germany) and impression materials were Aquasil Ultra (monophase regular set, Dentsply Caulk, Milford, Del, USA) and Imprint II Garant (regular body, 3M ESPE, Seefeld, Germany). They were used combinations from the same manufacture and exchanged combinations of the two. The drying time was designed to air dry, 5 minutes, 10 minutes, 15 minutes, 20 minutes, and 25 minutes. Total 240 of test specimens were prepared by auto-polymerizing tray material(Instant Tray Mix, Lang, Wheeling, Il, USA) with 10 specimens in each group. The specimens were placed in the Universal Testing machine (Instron, model 3366, Instron Corp, University avenue, Nowood, MA, USA) to perform the tensile test (cross head speed 5 mm/min). The statistically efficient drying time was evaluated through ANOVA and Scheffe test. All the tests were performed at 95% confidence level. RESULTS. The results revealed that at least 10 minutes is needed for Silfix-Aquasil, and 15 minutes for VPS Tray Adhesive-Imprint II, to attain an appropriate tensile bonding strength. VPS Tray Adhesive-Imprint II had a superior tensile bonding strength when compared to Silfix-Aquasil over 15 minutes. Silfix-Aquasil had a superior bonding strength to VPS Tray Adhesive-Aquasil, and VPS Tray Adhesive-Imprint II had a superior tensile bonding strength to Silfix-Imprint II at all drying periods. CONCLUSION. Significant increase in tensile bonding strength with Silfix-Aquasil and VPS Tray adhesive-Imprint II combination until 10 and 15 minutes respectively. Tray adhesive-impression material combination from the same company presented higher tensile bonding strength at all drying time intervals than when using tray adhesive-impression material of different manufactures.

• Journal of Periodontal and Implant Science
• /
• v.38 no.1
• /
• pp.7-14
• /
• 2008

Purpose: Chitosan & chitosan derivative(eg. membrane) have been studied in periodontal regeneration, and recently many studies of chitosan have reported good results. If chitosan's effects on periodontal regeneration are enhanced, we can use chitosan in many clinical and experimental fields. For this purpose, this study reviewed available literatures, evaluated comparable experimental models. Materials and Methods: Ten in vivo studies reporting chitosan's effects on periodontal tissue regeneration have been selected by use of the 'Pubmed' and hand searching. Results: 1. In Sprague Dawley rat calvarial defect models, amount of newly formed bone in defects showed significant differences between chitosan/chitosan-carrier/chitosan-membrane groups and control groups. 2. In beagle canine 1-wall intrabony defect models, amount of new cementum and new bone showed significant differences between chitosan/chitosan-membrane groups and control groups. The mean values of the above experimental groups were greater than the control groups. Conclusion: The results of this study have demonstrated that periodontal regeneration procedure using chitosan have beneficial effects, which will be substitute for various periodontal regenerative treatment area. One step forward in manufacturing process of chitosan membrane and in use in combination with other effective materials(eg. bone graft material or carrier) may bring us many chances of common use of chitosan in various periodontal area.

• Journal of the Korean Chemical Society
• /
• v.61 no.6
• /
• pp.346-351
• /
• 2017

This study was planned considering the chain length, hydrophilicity, and hydrophobicity of the additives to be used in the polymerization, while various ophthalmic lenses that use various additives with similar water contents were manufactured before their optical and physical properties were compared and analyzed. With regard to the additives required for manufacturing high-, medium-, and low-water content lens groups, HEA (hydroxyethyl acrylate), PVP (polyvinylpyrrolidone), and NMV(N-methyl-N-vinylacetamide) were used as additives for preparing the high-water content lens group, HEMA(2-hydroxyethyl methacrylate), HPMA(hydroxypropyl methacrylate) and BD(1,4-butanediol) were used for the medium-water content lens group. For the low-water content lens group, BMA(buthyl methacrylate), BDDA(1,4-butanediol diacrylate), and Bis-GMA(bisphenol A glycerolate diacrylate) were used, respectively. The average water content of HEA was 40.14%; that of PVP, 39.63%; and that of NMV, 40.52%. The mean of water content was 35.92% for HEMA, 35.74% for BD, and 34.62% for HPMA. For the low-water content lens group, the mean of water content was 26.69% for BMA, 27.76% for BDDA, and 26.14% for Bis-GMA. With regard to the results of the water content measurement using a moisture analyzer, the average water content of the high-water content lens group was 41.34% for HEA, 42.62% for PVP, and 42.73% for NMV. Finally, for the low-water content lens group, the average water content was 28.62% for BMA, 28.82% for BDDA, and 28.32% for Bis-GMA. The measurements of the water contents of the lenses using the two methods showed that the water content and refractive index of the lenses were similar in all the lens groups. The measurements of the contact angles, however, showed a different wettability value for each lens with a similar water content. Also, the change tendency of the lens curvature according to the change of time showed that the change amount became larger and the recovery time became longer from the lens samples with a lower water content to those with a higher water content. Based on these results that will be helpful for the study of ophthalmic lenses.

• Korean Journal of Agricultural Science
• /
• v.35 no.2
• /
• pp.155-165
• /
• 2008

A seasoned squid Jeotkal, Korean traditional fermented seafood, and its ingredients for manufacturing, including red hot pepper powder, ground garlic, sesame seeds, were irradiated with 0, 0.5, 1, 2, and 5 kGy by electron beam and stored at $4^{\circ}C$ for 4 weeks to determine the changes in microbiological and sensory characteristics. The initial contamination of squid Jeotkal such as total aerobic bacteria, yeast & mold, and coliform bacteria were at the levels of 2.88, 3.04, and 4.20 log CFU/g, respectively. However, electron beam irradiation with does at 5 kGy reduced the total aerobic bacteria to about 1 log CFU/g. Yeast & mold and coliform bacteria were reduced to 1-2 log CFU/g after 2 kGy of irradiation and reached to undetected level when the sample was irradiated at 5 kGy and following storage at $4^{\circ}C$ for 4 weeks. Sensory characteristics showed that electron beam irradiation of up to 5 kGy did not adversely affect overall acceptability of squid Jeotkal and its ingredients during cold storage. Therefore, electron beam irradiation is one of the possible means to improve storage stability of seasoned squid jeotkal, which has limited alternative sterilization methods due to the temperature characteristics of the products.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.2
• /
• pp.119-124
• /
• 2009

Statement of problem: The increasing demand for esthetic restorations has been required developing new materials for tooth colored restoration. Ceromer(Ceramic Optimized Polymer) has some advantages over porcelain, and has gained increasing popularity in restorative dentistry. However, there is little information on the dimensional changes in a clinical restoration in moist conditions. Purpose: This study examined the dimensional changes in Ceromer restorations with a clinical crown shape that were fabricated in a clinical manner. Material and methods: The crowns for the maxillary central incisor were fabricated with two Ceromers($BelleGlass^{(R)}$ and $Targis^{(R)}$) using a similar clinical restoration manufacturing technique. A total of twenty specimens were prepared and immersed in distilled water at room temperature to allow for water absorption. The weight, height and width were measured at 24, 72 and 168 hours. The accumulated ratios of the changes were calculated and evaluated using a paired t-test and an independent independent t-test. Results: The dimensions and weight increased with increasing soaking time. $Targis^{(R)}$ showed significant differences in height and weight between 24 hours and the other times(P<.05). $BelleGlass^{(R)}$ showed significant differences in width and weight between 24 hours and the other times. The two materials showed different changing patterns of the dimensions but there were no statistically significant differences between them. Conclusion: The dimensions and weight of the Ceromer restorations were changed by water absorption. The clinical crown shaped specimen showed more complicated dimensional changes than the simplified specimens.

• Weed & Turfgrass Science
• /
• v.5 no.1
• /
• pp.10-16
• /
• 2016

Proper actions such as discard, return or manufacturing should be taken to imported plants contaminated with quarantine weeds. Heat-treatment has been used as a processing method in many countries such as U.S., Australia, Canada as well as Korea. This study was carried to find appropriate heat-treatment methods for devitalizing dodder seeds mixed with plant seeds. Two species of dodder seeds and six imported seeds were treated for 1, 5, 10, 15, 30, 45 minutes or 1, 2, 4, 5, 6, 8 hours at the temperatures of $75^{\circ}C$, $80^{\circ}C$, $85^{\circ}C$, $90^{\circ}C$, $95^{\circ}C$, $100^{\circ}C$ and $120^{\circ}C$. According to the study, dodder seeds were devitalized at the conditions of $85^{\circ}C$ for 2 hours, $90^{\circ}C$ for 30 minutes, $95^{\circ}C$ and $100^{\circ}C$ for 15 minutes, $110^{\circ}C$ for 10 minutes and $120^{\circ}C$ for 5 minutes. Meanwhile, seed vigours of Cosmos bipinnatus and Callistephus chinensis had no difference when compared with untreated control at the heat-treatment conditions of $85^{\circ}C$ for 2 hours, $90^{\circ}C$ for 30 minutes.

• Korean Journal of Construction Engineering and Management
• /
• v.16 no.6
• /
• pp.101-111
• /
• 2015

The modular construction method has been getting more attention followed by global eco-friendly trend as the domestic construction industry has focused more on remodeling and extension work. The modular construction method is an industrialized construction system which is not likely as the existing construction method it manufactures more than 70% modules at the factory then assembling can be completed in a short amount of time on site. The modular construction method has various strengths; shortening of construction period by on-site work decrease, weight pressure reduction by usage of light steel frames and cost saving by repetitive manufacturing. However, it is currently not expanded due to the existing commercialized construction method. Therefore, this research is in order to help the related authorities make decisions to select the construction method and motivate expansion of modular construction method which can be utilized effectively in the extension works. The intention of this research is to stress differentiation from other construction methods in construction period, construction expenses, labor and forces by comparing and analyzing actual cases, to inform competitiveness of modular construction method by concrete effect analysis and to support adoption of the modular construction method into the domestic industry.

• Journal of Technologic Dentistry
• /
• v.34 no.3
• /
• pp.291-302
• /
• 2012

Purpose: It is to survey old men's utilization status of dental clinic and temporary-binding dentures and then to provide basic data to make a program for manufacturing old men's dentures and their teeth health education. Methods: Random selection was made on old men living in Daejeon and Chungnam, and a survey was conducted from April 15 to May 20, 2011. 500 questionnaires were distributed and 420 questionnaires were collected. Using spss 18.0 program, final analysis was made on 363 questionnaires except for 57 questionnaires which had missing value or showed some doubts about the unreliability. Results: 1. With respect to number of natural teeth as per the age, the upper/lower jaws had meaningful differences (P<.001), which means that the older the person is, the smaller number of natural teeth is. In the meantime, there was no meaningful difference according to sex. 2. With respect to kind of prosthetics installed in a mouth as per the age, there was meaningful difference in the upper jaws (P<.05) but there was no meaningful difference in the lower jaws. It was found out that the older the persons are, the more they use removable dentures while the younger the persons are, the more they use fixed partial dentures. 3. With respect to mouth health condition recognized by oneself, it showed bad (44.4%) and good (10.3%),which means recognition as bad is greater, and the age when prosthetics were first used is dispersed variously from below 40 to over 70. 4. Dental care institutions which they mainly used are hospital and clinics (91.5%), and 66.4% of them visited dental clinics lately. Preferential treatment if they go to dentists is as follows in the order of prosthetics (33.9%), gum treatment (24.2%) and pain treatment (14.9%). 5. 68.4% of them revisited dentists after installation of dentures and the reason for revisit is as follows in the order of poorly fitted dentures (35.1%), painful gum 25.9%, regular check-up 25.4% and difficult chewing 9.6%. Conclusion: As our country enters into an aging society, mouth health problem of old men has come to a serious issue, and therefore, a survey was conducted on some old men with respect to their utilization status of dental clinic and removable dentures in order to provide basic data for improvement of quality of their life, maintenance and enhancement of their mouth health. The study result shows that the older they are, the higher the loss rate of teeth as well as needs for prosthetics are, and thus it is thought the study will help to develop mouth health education program which may improve quality of old men's life by recovery of mouth functions declined due to loss of teeth and by regular check-up, education for mouth health control and following-up control of dentures.