• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2292-2295
• /
• 2001

In this paper, The control problem for a series DC motor is considered to adaptive fuzzy sliding-mode control scheme. Based on a nonlinear mathematical model of a series connected DC motor, instead of the combination of a nonlinear transformation and state feedback(feedback linearization) reduces the nonlinear control design. To demonstrate its effectiveness, an experimental study of this controller is presented. Two sets of fuzzy rule bases are utilized to represent the equivalent control input with unknown system functions of the main target. The membership functions of the THEN-part, which is used to construct a suitable equivalent control of SMC, are changed according to the adaptive law. With such a design scheme, we not only maintain the distribution of membership functions over state space but also reduce computing time considerably.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.4
• /
• pp.384-390
• /
• 2005

This paper addresses the design and implementation of a wireless network. proposed as a cost-effective support platform for PLCs. With this network. one or more supervising stations may access remote equipment like PLCs. An applicable communication methods are described and we applied efficient method among them to PLCs communication. The paper specifies these requirements and indicates methods to fulfill them. Also. it provides to the model of operation, and focuses on the implementation approach. The hardware and software design is described together with a number of critical points related to wireless communication on the Cnet. Furthermore, a discussion on system expandability and performance is tackled and some observations are stated. The main conclusion is, that the proposed method can feature good performance under normal operating conditions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.7
• /
• pp.637-643
• /
• 2010

The paper is about the development of 6-DOF active vibration isolation systems using VCM. Firstly, formulate the vertical 3-DOF mathematical model under eccentric load, and compare the model with the case in which the center of mass is located at the centroid. And then, complete the 6-DOF mathematical model by formulating the horizontal 3-DOF mathematical model. Find main parameters by comparing the result of the frequency response test with simulation result on the model. Finally, achieve the performance of vibration isolation by applying loop shaping approach & feedforward controller.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.10
• /
• pp.146-153
• /
• 1996

This paper presents the development of a collocated capacitance sensor and its application to the controller design for magnetic bearing supported rotor systems. The main feature of the sensor is that it is made of a compact printed circuit board(PCB) so that it can be built into the actuator coil of the magnetic bearing unit. The singnal processing unit hax been also developed. The experi- mental results of the sensor performance evaluation on sensitivity, bandwidth and resolution are presented. Then, simulation study shows the advantages of the collocated sensor for magnetic bearings over the nonco- llocated sensor. Finally, the experimental result on the performance of the collocated sensor based contrl- ler for a magnetic bearing rotor system is presented.

• International conference on construction engineering and project management
• /
• 2022.06a
• /
• pp.694-701
• /
• 2022

This paper introduces a study of concrete structures with a broken tire and a flat tire as a complete overhaul. The materials used to make concrete in this study are solid aggregate, cement, sand, flat tire, broken wheel, drinking water, and Ordinary Portland Cement. A total of 6 main compounds were thrown into solid cylinders and replaced by 0% as a controller followed by 5% and 10%. The cylinder pressure test of the concrete is done by applying the same pressure to the cylinders until a failure occurs. The results of the pressure test show that by applying 5% aggregation the pressure decreases. In Crumb wheel joints, the compression force decreases constantly as the percentage change increases. Therefore, the crumb wheel is not recommended for use as a complete replacement due to its compressive church power.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.515-519
• /
• 2004

A Propeller-Anemometer is an instrument used specifically, to measure the wind speed. The accurate measurement of the wind speed is vitally important such required by any weather stations. In this research, the measurand of the instrumentation was the rotational speed of the propeller and the instrumentation result or output data was wind velocity. The speed measured was recorded digitally in the computer by using specific software. A specific sensor used to measure a variable by converting information of the variable (rotational speed of the propeller) into a dependent signal such as electrical signal in form of voltage. The development of Propeller-Anemometer involved few sets of instrumentation process and equipment. It included three major parts, mechanical, electronics and computer. The main instrumentation processes were physical and signal interfacing, signal conditioning, logic interfacing, data transmission to computer and processing the data. Generally, this paper presents the overall concept and design of Propeller-Anemometer Instrumentation. However, an emphasis was mainly in designing and building the interfacing system, hardware and software. Basically, for the first phase of the development, this project designed and built the RS232 terminal using Peripheral Interface Controller (PIC), PIC16F873. The hardware can be interfaced to computer or other compatible devices. This routine converted input voltage from the circuit to speed (velocity) and transmitted them afterwards to the target device by using the RS232 transmission protocol. This implementation implied a computer display as visual interface. For the purpose of this paper, RS232 data transmission was carried out using a Microsoft Visual Basic software routine.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.11
• /
• pp.27-33
• /
• 2011

Recently many display devices support the digital display interface as display market growth. DisplayPort is a next generation display interface at the PC, projector and high definition content applications in more widely used connection solution development. This paper implements multiple streams based on the behavior of the main link that is suitable for the display port v1.1a standard. The limit point of Displayport, interface between the Sink Device and Sink Device is also implemented. And two or more differential image data are enable to output the result through four Lanes stated in display port v1.1a, of two or more display devices without the addition of a separate Lane. The Multiple Video Streaming Controller is implemented with 6,222 ALUTs and 6,686 register, 999,424 of block memory bits synthesized using Quartus II at Altera Audio/Video Development board (Stratix II GX FPGA Chip).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.7
• /
• pp.1603-1609
• /
• 2010

This Paper deals with a design, making a prtotype and test methods of Real-time towed Line Array Sensor Data processing board for fast data communication and long range data transmission with SFM(Serial FPDP Module) through Optic-fiber channel. Towed line array sensors are installed in Frigate and the each LAS A, B, C group data from LAS is packed a previously agreed protocol and transmitted to the signal processing unit. Considering the limited space of VME 6U size, LAS Data processing board is designed with MPC8265 PowerPC Controller of Freescale for main system control and Altera's CycloneIII FPGA for sensor data packing, self-test simulation data generation, S/W FIFO et cetera. LAS Data processing board have VxWorks, the RTOS(Real Time Operating System) that present many device drivers, peripheral control libraries on board for real-time data processing.

• Journal of Satellite, Information and Communications
• /
• v.12 no.4
• /
• pp.67-71
• /
• 2017

A solar array is main electrical energy source for Low-Earth-Orbit(LEO) satellite. The solar array cannot generate electrical energy during eclipse period, a battery supply electrical energy to the satellite. The electrical power of the solar array is changed in accordance with operating voltage and the solar array has the maximum power point. The solar array regulator makes the solar array supply electrical energy to the satellite and charge the battery. The solar array is connected to the solar array regulator input and the battery is connected to the solar array regulator output. The solar array regulator consists 2 of 3 hot redundant. One solar array regulator contains 3 DC-DC converters, and the solar array regulator operates stably even if the failure occur in one DC-DC converter. In this paper, the solar array regulator, the battery and the solar array operation is analyzed when the failure occur in one DC-DC converter.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1995.04a
• /
• pp.185-192
• /
• 1995

A common control model used to implement computer integrated manufacturing(CIM) is based on the hierarchical decomposition of the shop floor activities, in which supervisory controllers are responsible for all the interactions among subordinates. Although the hierarchical control philosophy provides for easy understanding of complex systems, an emerging manufacturing paradigm, agile manufacturing, requires a new control structure necessary to accommodate the rapid development of a shop floor controller. This is what is called CSCW(computer supported cooperative work)-based control or component-based heterarchical control. As computing resources and communication network on the shop floor become increasingly intelligent and powerful, the new control architecture is about to come true in a modern CIM system. In this paper, CSCW-based control is adopted and investigated, in which a controller for a unit of device performs 3 main functions - planning, scheduling and execution. In this paper, attention is paid to a planning function and all the detailed planning activities for CSCW-based shop floor control are identified. Interactions with other functions are also addressed. Generally speaking, planning determines tasks to be scheduled in the future. In other words, planning analyzes process plans and transforms process plans into detailed plans adequate for shop floor control. Planning is also responsible for updating the process plan and identifying/resolving replanning activities whether they come from scheduling or execution.