• 한국유체기계학회 논문집
• /
• 제12권5호
• /
• pp.39-46
• /
• 2009

This paper outlines how the on-line performance monitoring system can be used to improve the efficiency and maintenance of the equipments. And a method of the heat rate allocation to each equipment was suggested to monitor the performance of combined cycle power plants. This calculates the expected heat rate of current conditions and compares it with actual values. Loss allocation in heat rate is reconciled by calculating the magnitude of the deficiency contributed by major components, such as the gas turbine, heat recovery steam generator, steam turbine and condenser. Expected power output is determined by a detailed model and correction curves of the plant. This simulation models are found to reproduce high accuracy in behavior of the cycle for various operating conditions, both in design and in off-design condition. Errors are lower than 2% in most cases.

• Bulletin of the Korean Chemical Society
• /
• 제35권12호
• /
• pp.3482-3488
• /
• 2014

Matrix-induced mass bias and its effect on the accuracy of isotope ratio measurements have been examined for a quadrupole-based inductively coupled plasma-mass spectrometer (Q ICP-MS). Matrix-induced mass bias effect was directly proportional to % mass difference, and its magnitude varied for element and nebulizer flow rate. For a given element and conditions in a day, the effect was consistent. The isotope ratio of Cd106/Cd114 under $200{\mu}g\;g^{-1}$ U matrix deviated from the natural value significantly by 3.5%. When Cd 111 and Cd114 were used for the quantification of Cd with isotope dilution (ID) method, the average of differences between the calculated and measured concentrations was -0.034% for samples without matrix ($0.076{\mu}g\;g^{-1}$ to $0.21{\mu}g\;g^{-1}$ for the period of 6 months). However, the error was as large as 1.5% for samples with $200{\mu}g\;g^{-1}$ U. The error in ID caused by matrix could be larger when larger mass difference isotopes are used.

• 소음진동
• /
• 제6권2호
• /
• pp.215-224
• /
• 1996

Active vibration control is generally used to reduce vibration level by the actuators based on measured signal. Dynamic properties of a structure can be easily modified by the active vibration control, so that the vibration level may be effectively reduced to the magnitude below the allowable limit over a wide frequency rangs. In this paper, an instantaneous optimal control algorithm including acceleration feedback is presented for the active vibration control of large structures considering facts that the acceleration response can be easily measured, but the displacement and velocity response are obtained by numerically integrating the measured acceleration response with some errors. The adverse effect of the time delay is overcomed by taking into account the dynamic characteristics of an actuator and filters in the design of controller. Performance test is carried out using a hydraulic active mass driver on a test structure$(L{\times}W{\times}H;=;1200mm{\times}800mm{\times}1600mm, about;500kg)$ supported by four columns under base excitations. It is confirmed that the vibration level of the test structure are reduced to about 1/6 near resonance.

• 대한토목학회논문집
• /
• 제12권2호
• /
• pp.141-150
• /
• 1992

본 연구에서는 한강유역의 6개 관측점 (T/M국)에 대하여 단기간 기록년수의 홍수량 자료를 통계학적 방법에 기초된 홍수빈도해석모형인 POT모형에 적용하여 빈도해석을 실시함으로써 모형의 적용 타당성을 검토함과 아울러 하천유역의 지점별 홍수량의 빈도 및 크기를 추정하였고, 미계측 유역에서 수공구조물의 계획설계에 기준이 될 수 있는 설계 홍수량을 산정할 수 있는 지역빈도해석에 의한 통계학적 지역화 모형의 개발가능성을 검토 하였다.

• Communications for Statistical Applications and Methods
• /
• 제14권3호
• /
• pp.561-576
• /
• 2007

Five plotting positions are applied to the computation of probability weighted moments (PWM) on the parameters of the generalized logistic distribution. Over a range of parameter values with some finite sample sizes, the effects of five plotting positions are investigated via Monte Carlo simulation studies. Our simulation results indicate that the Landwehr plotting position frequently tends to document smaller biases than others in the location and scale parameter estimations. On the other hand, the Weibull plotting position often tends to cause larger biases than others. The plotting position (i - 0.35)/n seems to report smaller root mean square errors (RMSE) than other plotting positions in the negative shape parameter estimation under small samples. In comparison to the maximum likelihood (ML) method under the small sample, the PWM do not seem to be better than the ML estimators in the location and scale parameter estimations documenting larger RMSE. However, the PWM outperform the ML estimators in the shape parameter estimation when its magnitude is near zero. Sensitivity of right tail quantile estimation regarding five plotting positions is also examined, but superiority or inferiority of any plotting position is not observed.

• 한국통신학회논문지
• /
• 제38C권7호
• /
• pp.643-649
• /
• 2013

본 논문에서는 무선통신기기에서 필수적으로 사용되는 안테나의 근접 전자기장 변화에 의한 반사계수의 변화를 토대로 하여 사람의 심박신호를 검출한다. 반사되는 신호를 검출하기 위하여 20 dB의 directional coupler를 사용하여 송신신호에 영향을 주지 않고 안테나의 반사계수를 검출하는 회로를 사용하였다. 사람의 심박에 의한 다이폴 안테나의 반사계수는 약 0.07 dB 가량 변하게 되어 검출하기 어려우므로, 민감도를 향상시키는 방법을 적용하여 심박신호를 깨끗하게 잡아내었다. Discrete한 소자의 사용으로 오차가 발생하는 것을 감안하여 안테나의 위치를 움직여 최적 지점에서 더 좋은 심박신호의 결과를 나타내는 것을 확인하였고, 일반적인 통신신호에서도 가능한지 확인하기 위하여 4 MHz 대역의 FM신호를 사용하여 잘 동작하는 것을 검증하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.112-118
• /
• 2005

Ball bearings which were fitted between housing and shaft play an important role in rotating shaft system smoothly, Therefore bearing's running accuracy has significant influence on that of rotating machinery. Manufacturing accuracy of bearings as well as that of shaft and housing is main factor to affect bearing running accuracy In this paper, bearing's vibration and fatigue life considering raceway roundness of ball bearing before and after being fitted into housing are theoretically estimated. To perform analysis, a simple three degrees of freedom model was proposed and then these analysis was conducted utilizing the Newton-Raphson iterative method. The results show that vibration magnitude of ball bearing fitted into housing is considerably larger than before assembly, and bearing's theoretical L$_{10}$ fatigue life that ninety percent of the bearing population will endure decreased in about fifty percent.

• Nuclear Engineering and Technology
• /
• 제32권3호
• /
• pp.235-243
• /
• 2000

A one-dimensional neutronics formulation is established within the framework of the nonlinear analytic nodal method such that it can result in consistent one-dimensional models that produce the same axial information as their corresponding reference three-dimension81 models. Consistency is achieved by conserving axial interface currents as well as the planar reaction rates of the three-dimensional case. For current conservation, flux discontinuity is introduced in the solution of the two-node problem. The degree of discontinuity, named the current conservation factor, is determined such that the surface averaged axial current of the reference three-dimensional case can be retrieved from the two-node calculation involving the radially collapsed group constants and the discontinuity factor. The current conservation factors are derived from the analytic nodal method and various core configurations are analyzed to show that the errors in K-eff and power distributions can be reduced by a order of magnitude by the use of the current conservation factor with no significant computational overhead.

• 전력전자학회논문지
• /
• 제9권3호
• /
• pp.267-274
• /
• 2004

본 논문에서는 새로운 온라인 데드타임 전향보상기법을 제안한다. 데드타임 효과(dead-time effect)로 인한 출력 전압 오차를 외란전압으로 간주하고 이를 추정하여 전향보상한다. 외란전압의 크기를 시간지연제어기법을 이용하여 추정하고, 추정된 값과 측정된 전류와 위치 정보로써 외란전압을 계산한다. 데드타임 효과를 보상하기 위해 계산된 외란전압은 전압지령에 전향된다. 제안된 방법은 DSP TMS320C31을 사용하여 디지털방식으로 영구자석 동기 전동기 구동 시스템에 적용이 된다. 제안된 방법의 효용성을 검증하기 위해 이 시스템에서 실험을 수행하였고 그 결과는 제안된 방법의 효과를 잘 보여주고 있다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.978-983
• /
• 2003

In this paper, we propose a fault detection method for extended Kalman filter in decentralized filter structure. To detect a fault, a consistency between filter output and a monitoring signal is tested. State propagators are used to obtain the monitoring signal. However, the output of state propagator increases in magnitude and finally diverges as time runs. To solve such problem, two-propagator method was proposed for linear system. Two propagators are reset by Kalman filter output, alternatively, to avoid divergence. But a test statistics change abruptly at the reset instant in that method. Hence a N-step propagator method is proposed to fix up the problem. In the N-step propagator, only time propagations are performed from k-N+1 step to k step without measurement updates. A test statistics are defined by errors and its covariance between extended Kalman filter and N-step propagator. These fault detection methods are applied to integrated strapdown inertial navigation system (SDINS). By computer simulation, it is shown that the proposed methods detect a fault effectively.