• Communications of the Korean Mathematical Society
• /
• v.35 no.4
• /
• pp.1269-1281
• /
• 2020

In this article, we show that a pseudo-Hermitian magnetic curve in a normal almost contact metric 3-manifold equipped with the canonical affine connection ${\hat{\nabla}}^t$ is a slant helix with pseudo-Hermitian curvature ${\hat{\kappa}}={\mid}q{\mid}\;sin\;{\theta}$ and pseudo-Hermitian torsion ${\hat{\tau}}=q\;cos\;{\theta}$. Moreover, we prove that every pseudo-Hermitian magnetic curve in normal almost contact metric 3-manifolds except quasi-Sasakian 3-manifolds is a slant helix as a Riemannian geometric sense. On the other hand we will show that a pseudo-Hermitian magnetic curve γ in a quasi-Sasakian 3-manifold M is a slant curve with curvature κ = |(t - α) cos θ + q| sin θ and torsion τ = α + {(t - α) cos θ + q} cos θ. These curves are not helices, in general. Note that if the ambient space M is an α-Sasakian 3-manifold, then γ is a slant helix.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.37-43
• /
• 2004

The performance of magnetic abrasive finishing fur surface is evaluated by the characteristic curve. The characteristic curve is generated by experiment in surface finishing. For experiment, new magnetic inductor is designed and manufactured. 15 kinds of powders are provided to find the relationship between powder characteristic and finishing performance. As powder, Fe-TiC. Polymer-TiC and Fe-NbC are used with different size. The size of abrasives and location are also important factor for the performance. From characteristic curve, two index are obtained, which specify the initial finishing performance and endurance of finishing performance. It is proved that the performance index can be applied to select proper powder for efficient deburring. It is shown that the characteristic curve can be used as good tools for evaluating powder performance in surface finishing and deburring.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.3
• /
• pp.417-421
• /
• 2015

In this paper, study for B-H curve characteristics of the magnetic material due to tensile stresses of submarine for magnetic silence. For the experiment, made the sample of the material of AH36 and made to a B-H curve Tracer. In addition, design and made a system of stress by the weight in order to apply a tensile stress, it was possible to obtain results for the change of the magnetization.

• Journal of Magnetics
• /
• v.20 no.3
• /
• pp.258-264
• /
• 2015

In this paper, an adequate B-H curve extrapolation method is proposed and its reliability is verified through experiments. A method is developed to estimate the magnetic saturation induction from the density of the lamination core and electrical resistivity. The magnetic saturation induction of electrical steels measured using a vibration sample magnetometer are compared with the analytical results to validate the accuracy of the proposed estimation method. It is found that the predicted error in the magnetic saturation induction of the electrical steels are approximately 1.2% when the proposed method is used. The performance of interior permanent magnet synchronous motors that applies the proposed method are evaluated via 2D nonlinear finite element analysis and through experiments. Based on the obtained results, the extrapolated B-H curves from the estimated saturation induction can be used for various analyses in saturation region.

• Journal of Fisheries and Marine Sciences Education
• /
• v.19 no.3
• /
• pp.510-516
• /
• 2007

The efficiency of magnetic compass direction sensor and magnetic compass by the laboratory experiment for the apparatus of generating artificial magnetic force and the onboard experiment on the fishing boat of coastal pot at the outside of Pusan Namhang were investigated. The results showed that the bearing angle of magnetic compass direction sensor was coincided with that of magnetic compass. However, the performance of magnetic compasses was unsuitable under the ISO rule by the characteristic experiment of damping curve. Therefore, the use of autopilot system using magnetic compass direction sensor which is based on the magnetic compass needs the sufficient notice.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.2 s.173
• /
• pp.355-361
• /
• 2000

In this study, active control magnetic actuator for reducing vibration of rotor system is performed. Identification, modeling, simulation, control system design, and evaluation of active magnetic damper system have been researched. Power amplifier modeling, connected magnetic actuator and augmented by system identification, is included to establish a magnetic damper simulation which provides close performance correspondence to the physical plant. A magnetic actuator, digital controller using DSP(Digital Signal Processor), and bipolar operational power supply/amplifiers are developed to show the effectiveness of reducing rotor vibration. Also the curve fitting procedure to obtain the transfer function of frequency dependent components is developed. Two kinds of test are executed as sliding and oil bearing. Results presented in this paper will provide a well-defined technical parameters in designing magnetic damper system for the proposed rotor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.515-518
• /
• 2002

In this study, the ellipsoidal cap type magnetic pole structure was proposed for the electro-magnet in B-H curve tracer. From the simulation for the electro-magnet without specimen, the area of effective uniform field(99% range for the central field value) was considerably increased in case of the newly proposed ellipsoidal cap type magnetic pole than that of the conventional simple-inclined cap type magnetic pole. Also, through the simulation for the electro-magnet with permanent magnet specimen(NaFe30), the optimal Positions of the magnetic field measurement sensor(Hall sensor) were found out in each case and the errors were decreased in case of the newly proposed ellipsoidal cap type magnetic pole.

• The Pure and Applied Mathematics
• /
• v.27 no.2
• /
• pp.83-96
• /
• 2020

In this paper we study Biharmonic curves, Legendre curves and Magnetic curves in three dimensional f-Kenmotsu manifolds. We also study 1-type curves in a three dimensional f-Kenmotsu manifold by using the mean curvature vector field of the curve. As a consequence we obtain for a biharmonic helix in a three dimensional f-Kenmotsu manifold with the curvature κ and the torsion τ, κ² + τ² = -(f² + f'). Also we prove that if a 1-type non-geodesic biharmonic curve γ is helix, then λ = -(f² + f').

• Journal of applied mathematics & informatics
• /
• v.40 no.3_4
• /
• pp.587-601
• /
• 2022

We find the characterizations of the curvatures of Legendre curves and magnetic curves in Kenmotsu manifolds with C-parallel and C-proper mean curvature vector fields in the tangent and normal bundles. Finally, an illustrative example is presented.

• Proceedings of the KIEE Conference
• /
• 2007.11a
• /
• pp.83-85
• /
• 2007

In magnetic field analysis of electrical machines, hysteresis phenomena of B-H curves should be taken into account in order to obtain more accurate results. In this paper, the hysteresis modeling using the micromagnetics for the magnetic field analysis is investigated. In the micromagnetics, usually, it takes much CPU times. Therefore, the method for representing hysteresis phenomena by minimum modeling is investigated in order to applying it to the magnetic field analysis. First, the micromagnetics is described. Then, the method of minimum modeling is shown. Finally, the hysteresis curve obtained by the minimum modeling is demonstrated. The effect of parameters of micromagnetics on the shape of hysteresis curve is investigated.