• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.1
• /
• pp.33-38
• /
• 2008

The probability of an oscillation occurrence in M/W frequency conversion repeaters is low on account of the different operating frequency of the input and output signals. The probability of interference caused by the M/W frequency conversion repeaters to other systems is also low because the systems are used in the line-of-sight. Therefore M/W frequency conversion repeaters are generally used for retransmitting the signal received from base station to the islands. This paper describes the design and implementation of analog predistorter for M/W frequency conversion repeaters in mobile communications. The M/W repeaters convert IF frequency of 1010+/-10MHz to RF frequency of 11GHz. A predistorter can be designed for the M/W repeater operating in either IF or M/W frequency. In this paper IF predistorter operated in 1010MHz is designed and implemented because a M/W predistorter operated in 11GHz is difficult to implement. The IF predistorter can linearize RF modules in the repeater followed by IF stages. The performance test results show that the implemented analog predistorter improves ACPR of 10dB at the output power of 25dBm with the signal frequency of 10.805GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.11 s.353
• /
• pp.175-184
• /
• 2006

In this paper, we describe a 900MHz CMOS RF transceiver using an ISM band for ZigBee applications. The architecture of the designed rx front-end, which consists of a low noise amplifier, a down-mixer, a programmable gain amplifier and a band pass filter. And the tx front-end, which consists of a band pass filter, a programmable gain amplifier, an up-mixer and a drive amplifier. A low-if topology is adapted for transceiver architecture, and the total current consumption is reduced by using a low power topology. Entire transceiver is verified by means of post-layout simulation and is implemented in 0.18um RF CMOS technology. The fabricated chip demonstrate the measured results of -92dBm minimum rx input level and 0dBm maximum tx output level. Entire power consumption is 32mW(@1.8VDD). Die area is $2.3mm{\times}2.5mm$ including ESD protection diode pads.

• Journal of IKEEE
• /
• v.11 no.1 s.20
• /
• pp.15-23
• /
• 2007

This paper describes a dual frequency synthesizer designed in a 0.2$\mu$m CMOS technology for wireless LAN applications. The design is focused mainly on low-power characteristics. Power dissipation is minimized especially in VCO and prescaler design. The designed synthesizer includes all building blocks for elimination of external components, other than the crystal. Its operating frequency can be programmed by external data. It operates in the frequency range of 2.3GHz to 2.7GHz (RF) and 250MHz to 800MHz (IF) and consumes 5.14mA at 2.5GHz and 1.08mA at 0.5GHz from a 2.5V supply. The measured phase noise is -85dBc/Hz in-band and -105dBc/Hz at 1MHz offset at IF band. The die area is 1.7mm$\times$1.7mm.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.37-44
• /
• 2007

A low-voltage high-linear bipolar OTA and its application to IF bandpass filter for GSM cellular telephone are presented. The OTA consists of a low-voltage linear transconductor, a translinear current gain cell, and three current mirrors. The bandpass filter is composed of two cascaded identical second-order bandpass filters, which consist of a resistor, a capacitor, and a grounded simulated inductor realized with two OTA's and a grounded capacitor. SPICE simulations using an 8 GHz bipolar transistor-array parameter show that the OTA with a transconductance of 1 mS exhibits a linearity error of less than ${\pm}2%$ over an input voltage range of ${\pm}0.65\;V$ at supply voltages of ${\pm}2.0\;V$. Temperature coefficient of the transconductance is less than $-90ppm/^{\circ}C$. The bandpass filter has a center frequency of 85 MHz and Q-factor of 80. Temperature coefficient of the center frequency is less than $-182ppm/^{\circ}C$. The power dissipation of the filter is 128 mW.

• Journal of electromagnetic engineering and science
• /
• v.8 no.2
• /
• pp.76-83
• /
• 2008

A low power(9 mW) highly-digitized 2.4 GHz receiver for sensor network applications(IEEE 802.15.4 LR-WPAN) is realized by a $0.18{\mu}m$ CMOS process. We adopted a novel receiver architecture adding an intermediate frequency (IF) level detection scheme to a low-power complex fifth-order continuous-time(CT) bandpass L:tl modulator in order to digitalize the receiver. By the continuous-time bandpass architecture, the proposed $\Sigma\Delta$ modulator requires no additional anti-aliasing filter in front of the modulator. Using the IF detector, the achieved dynamic range(DR) of the over-all system is 95 dB at a sampling rate of 64 MHz. This modulator has a bandwidth of 2 MHz centered at 2 MHz. The power consumption of this receiver is 9.0 mW with a 1.8 V power supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.110-115
• /
• 2000

A K-band GaAs MMIC receiver module has been developed using 0.15 ${\mu}{\textrm}{m}$ HEMT technology process. It incorporates two front end low noise amplifiers, a double balanced diode mixer, and filters. The RF input frequency ranges 20.1 to 21 GHz and the IF output 1.1 to 2 GHz. Test results show an overall conversion gain of more than 27 dB, and less than a 2.2 dB noise figure. The image-rejection ratio greater than 21 dB has been obtained. The isolation between RF and IF ports is better than 27 dB, and between LO and IF is more than 50 dB.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.1
• /
• pp.153-156
• /
• 2009

Low temperature methane steam reforming to produce $H_2$ for fuel cells has been calculated thermodynamically considering both heat loss of the reformer and unreacted $H_2$ in fuel cell stack. According to the thermodynamic equilibrium analysis, it is possible to operate methane steam reforming at low temperatures. A scheme for the low temperature methane steam reforming to produce $H_2$ for fuel cells by burning both unconverted $CH_4$ and $H_2$ to supply the heat for steam methane reforming has been proposed. The calculated value of the heat balance temperature is strongly dependent upon the amount of unreacted $H_2$ and heat loss of the reformer. If unreacted $H_2$ increases, less methane is required because unreacted $H_2$ can be burned to supply the heat. As a consequence, it is suitable to increase the reaction temperature for getting higher $CH_4$ conversion and more $H_2$ for fuel cell stack. If heat loss increases from the reformer, it is necessary to supply more heat for the endothermic methane steam reforming reaction from burning unconverted $CH_4$, resulting in decreasing the reforming temperature. Experimentally, it has been confirmed that low temperature methane steam reforming is possible with stable activity.

• Journal of Distribution Science
• /
• v.12 no.10
• /
• pp.123-128
• /
• 2014

Purpose - The purpose of the study is to reexamine the price fairness as practiced by low cost airlines, as a consumer has to experience such inconveniences as inferior airport transportation, extra fees on in-flight meals, and non-negotiable seats, and consumers evaluate such experiences keeping in mind their total costs. This evaluation includes price fairness and allows a reasonable and overall consideration of factors of low cost airlines. It tries to set up a measurement of the indicators consumers' perceptions of price fairness academically as it adapts price fairness to airline services which are renowned for price volatility. Research design, data, and methodology - The research proposes an alternative pricing strategy for the long term profit of low cost airlines after going over conflicts between the traditional theory of consumers' price perception mechanism and flexible fair policy of low cost airlines. It was meaningful when it relates to the early stage of the business, while it enhances the risks relating to the long term survival of low cost airlines. In addition, it is significant as it highlights the negative influences on consumers' perceptions of price fairness, as low cost airlines run on extremely low cost perspectives. Results - The results of the research provide insight into four perspectives, as consumers' perceptions of price fairness are influenced by the frequency and range of price changes and services. The first perspective is that it would lead to positive price evaluation when a low cost airline cuts prices frequently with little changes than one big change. It also would lead to the same result when it comes to necessary services. The second perspective is that one big increase of price would rather undermine the negative aspects of price changes than those of several smaller ones. The third perspective is that additional services would be good to consumers' perceptions of price fairness as compared to discount benefits with respect to the cost. Finally, a low cost airline should consider that consumers will change airlines or defer their flight schedule if the flight fares increase beyond their limits. Conclusions - Low cost airlines should reconsider their pricing policies for services that were provided free earlier. A consumer would not like discount benefits when made to pay for services that were, for long, free of charge. If a low cost airline can provide services with no charge, it should improve volumes if the costs are standardized and, moreover, should consider the charging fees. Alternatively, a consumer can choose between services and fair discount. Low cost airlines are implementing sales promotion strategies, as the competition is more intense than it used to be. In these days, they should regard services over sales promotion, as consumers may prefer to spend money on good premium services. Some differentiation in services could create a good market position for the airlines and, hence, good financial performance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.840-845
• /
• 2013

In this paper, the broadband frequency double down-converter based on LC filter technologies has been designed and implemented, and its performances are introduced. The Designed frequency double down-converter is consisted with a low-noise amplifier, mixer, IF amplifier, LC filter, DC-block capacitor and RF-bypass capacitor. Especially, instead of active devices of a typical converter, the suggested converter designed using passive devices to provide both low-power consumption and low-cost model. As results of the measurement, the implemented frequency double down-converter realizes the broadband performance with the bandwidth of 100MHz (13~113MHz) at the center frequency of 63MHz, and its gain is approximately 40dB.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.229-234
• /
• 2002

The variation of HAZ toughness with nitrogen content and weld cooling rate was investigated and interpreted in terms of both microstructure and the amount of free nitrogen. The presence of free nitrogen in HAZ was investigated by internal friction measurement and its amount was measured by hydrogen hot extraction analysis. Both nitrogen content and weld cooling rate influenced HAZ microstructure and high toughness was obtained at a mixed microstructure of acicular ferrite, feffite sideplate and polygonal ferrite. If nitrogen content is too low or cooling rate is too fast, bainitic microstructure is obtained and toughness is low. On the other hand, if nitrogen content is too high or cooling rate is too slow, coarse polygonal ferritic microstructure is obtained and toughness is deteriorated again. ill addition to the microstructural change, high nitrogen content also resulted in a large amount of free nitrogen. Therefore, nitrogen content should be kept as low as possible even if the mixed micostructure is obtained. In this experimental condition, the maximum toughness was obtained at 0.006% nitrogen content when weld cooling time ($\Delta$t$_{8}$5/)) is 60s.TEX>5/)) is 60s.