• 대한기계학회논문집B
• /
• 제23권11호
• /
• pp.1379-1389
• /
• 1999

A new technique for control of size and shape of flame-made particles is Introduced. The characteristic sintering time can be controlled Independently of collision time by heating the particles with irradiation of laser because the sintering time strongly depends on temperature. A coflow oxy-hydrogen diffusion flame burner was used for $SiCl_4$ conversion to silica particle. Nanometer sized aggregates irradiated by a high power CW $CO_2$ laser beam were rapidly heated up to high temperatures and then were sintered to approach volume-equivalent spheres. The sphere collides much slower than the aggregate, which results in reduction of sizes of particles maintaining spherical shape. Light scattering of Ar ion laser and TEM observation using a local sampling device were used to confirm the above effects. When the $CO_2$ laser was irradiated at low position from the burner surface, particle generation due to gas absorption of laser beam occurred and thus scattering intensity increased with $CO_2$ laser power. At high irradiation position, scattering intensity decreased with $CO_2$ laser power and TEM image showed a clear mark of evaporation and recondensation of particles for high $CO_2$ laser power. When the laser was irradiated between the above two positions where small aggregates exist, average size of spherical particles obviously decreased to 58% of those without $CO_2$ laser irradiation with the spherical shape. Even for increased carrier gas flow rate by a factor of three, TEM photograph also revealed considerable reduction of particle size.

• 한국전기전자재료학회논문지
• /
• 제29권4호
• /
• pp.237-240
• /
• 2016

The improvement of irradiation intensity and irradiation uniformity is essential for large area and high power UVA light source application. In this study, large number of chips bonded by micro soldering technique were driven by low current, and current limiting diodes were configured to supply constant current to parallel circuits consisting of large number of series strings. The dimension of light source module circuit board was $350{\times}90mm^2$ and 16,650 numbers of 385 nm flip chip LEDs were used with a configuration of 90 parallel and 185 series strings. The space between LEDs in parallel and series strings were maintained at 1.9 mm and 1.0 mm distance, respectively. The size of the flip chip was $750{\times}750{\mu}m^2$ were used with contact pads of $260{\times}669{\mu}m^2$ size, and SAC (96.5 Sn/3.0 Ag/0.5 Cu) solder was used for flip chip bonding. The fabricated light source module with 7.5 m A supply current showed temperature rise of $66^{\circ}C$, whereas irradiation was measured to be $300mW/cm^2$. Inaddition, 0.23% variation of the constant current in each series string was demonstrated.

• 한국재료학회지
• /
• 제23권12호
• /
• pp.708-713
• /
• 2013

Graphene oxide has been synthesized by microwave-assisted exfoliation of graphite oxide prepared by modified Hummers method. Graphite was oxidized in a solution of $H_2O_2$ and $KMnO_4$ at $65{\sim}80^{\circ}C$, followed by 10 % $H_2O_2$ solution treatment at $80{\sim}90^{\circ}C$. The graphite oxide was exfoliated under microwave irradiation of 1 kW and was reduced to graphene effectively by hydrazine hydrate ($H_4N_2{\cdot}H_2O$) treatment. The exfoliation of graphene oxide was significantly affected by the microwave irradiation on (heating)/off (cooling) period. An on/off period of 10 s/20 s resulted in much more effective exfoliation than that of 5 s/10 s with the same total treatment time of 10 min. This can be explained by the higher exfoliation temperature of 10 s/20 s. Repetition of the graphite oxidation and exfoliation processes also enhanced the exfoliation of graphene oxide. The thickness of the final graphene products was estimated to be several layers. The D band peaks of the Raman spectra of the final graphene products were quite low, suggesting a high crystal quality.

• 한국진공학회지
• /
• 제18권5호
• /
• pp.384-389
• /
• 2009

ZnO는 육방정계결정구조의 물질로서 3.37 eV의 넓은 띠 간격과 60 meV의 큰 exciton 결합에너지에 따른 높은 효율의 자외선발광으로 짧은 파장의 빛 (녹, 청, 자외선)을 내는 LED (Light Emitting Diode) 분야에서 관심을 기울이고 있는 물질이다. LED제작을 위해서는 n형의 ZnO와 p형의 ZnO가 필요하지만 기본적으로 ZnO은 n형이므로 신뢰성 있는 p형 ZnO박막을 제작하기 위한 노력이 기울여지고 있다. 본 연구에서는 ALD (Atomic Layer Deposition)로 제작된 ZnO박막에 20 keV의 에너지를 갖는 질소이온을 $10^{13}{\sim}10^{15}ions/cm^2$로 조사한 후 Hall 효과 측정장치를 이용하여 질소이온 조사에 따른 전기적 특성변화를 조사하였다.

• 한국식품위생안전성학회지
• /
• 제15권1호
• /
• pp.1-4
• /
• 2000

ESR spectroscopy를 이용하여 게류의 방사선 조사 유무와 선량관계 및 EAR신호의 안정성에 관하여 알아보았다. 꽃게와 방게를 0, 1, 3, 5, 그리고 7 kGy로 방사선을 조사한 후 살을 제거하고 집게다리, 등 일반다리의 겉 표피만을 취해 건조시킨 다음, Burker Win-EPR spectroscopy를 이용하여 신호의 특성을 알아보았다. 방사선 조사된 꽃게와 방게 시료는 g$_1$=2.002$\pm$0.0003, g$_2$=1.998$\pm$0.0005에서 특유의 비대칭 신호를 나타내어 비조사 시료와 뚜렷하게 구별되었으며, 각 시료의 부위별 비교는 꽃게와 방게에서는 똑같이 집게다리>등>일반다리의 순으로 신호의 차이가 나타났다. 조사선량의 증가에 따른 ESR 신호의 높이는 직선적으로 증가하였다. 또한 이들 신호의 크기는 5$^{\circ}C$에서 9주간의 저장기간에서도 안전하여 방사선 조사 유무의 판별은 장기간의 저장에서도 가능하였다 따라서 ESR spectroscopy를 이용한 방사선 조사 게류의 검지법은 빠르고 확실하며 준정량적인 방법임을 알 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 논문집 센서 박막재료연구회 및 광주 전남지부
• /
• pp.69-72
• /
• 2008

Decay processes of accumulated charge in e-beam irradiated polymers during elevating temperature are observed using pulsed electro-acoustic measurement system. Since the polymeric materials have many superior properties such as light-weight, good mechanical strength, high flexibility and low cost, they are inevitable materials for spacecrafts. In space environment, however, the polymers sometimes have serious damage by irradiation of high energy charged particles. When the polymers of the spacecraft are irradiated by high energy charged particles, some of injected charges accumulate and remain for long time in the bulk of the polymers. Since the bulk charges sometimes cause the degradation or breakdown of the materials, the investigation of the charging and the decay processes in polymeric materials under change of temperature is important to decide an adequate material for the spacecrafts. By measuring the charge behavior in e-beam irradiated polymer, such as polyimide or polystyrene, it is found that the various accumulation and decay patterns are observed in each material. The results seem to be useful and be helpful to progress in the reliability of the polymers for the spacecraft.

• 전기학회논문지
• /
• 제60권11호
• /
• pp.2064-2075
• /
• 2011

In this paper, robust multi-level perturbation and observation (MLPO) maximum power point tracking (MPPT) control are presented of the environmental change including the solar radiation and temperature. Because the maximum power point of the Photovoltaic (PV) is changing according to the solar radiation and temperature, the technology which traces the maximum power point in order to increase the power efficiency is recognized as the very important part. The general requirement for the MPPT is that system is simple, the cost is inexpensive, the PV tracking function and output change are small. Conventional perturbation and observation (PO) method is a simple system but there is the disadvantage that an efficiency of system becomes low. In addation, the incremental conductance (IC) control is required expensive CPU because of a large of calculations. In order to solve this problem, in this paper, the MLPO MPPT control using the method diversifying the step size according to the environment condition is presented. The validity of the MLPO method presenting from this paper is proved through analyzing the solar power generation output error at the steady state.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.329-330
• /
• 2007

Decay processes of accumulated charge in e-beam irradiated polymers during elevating temperature are observed using pulsed electro-acoustic measurement system. Since the polymeric materials have many superior properties such as light-weight, good mechanical strength, high flexibility and low cost, they are inevitable materials for spacecrafts. In space environment, however, the polymers sometimes have serious damage by irradiation of high energy charged particles. When the polymers of the spacecraft are irradiated by high energy charged particles, some of injected charges accumulate and remain for long time in the bulk of the polymers. Since the bulk charges sometimes cause the degradation or breakdown of the materials, the investigation of the charging and the decay processes in polymeric materials under change of temperature is important to decide an adequate material for the spacecrafts. By measuring the charge behavior in e-beam irradiated polymer, such as polyimide or polystyrene, it is found that the various accumulation and decay patterns are observed in each material. The results seem to be useful and be helpful to progress in the reliability of the polymers for the spacecraft.

• 전자공학회논문지
• /
• 제51권6호
• /
• pp.71-77
• /
• 2014

본 연구에서는 radio frequency(rf) 마그네트론 스퍼터링 기술을 이용하여 Corning 유리 기판에 증착된 InGaZnO (IGZO) 박막의 광 투과도 특성에 고 에너지 전자빔 조사(high-energy electron beam irradiation (HEEBI))이 미치는 영향을 연구하였다. 저온에서 증착된 IGZO 박막은 공기 중 과 상온 조건에서 0.8 MeV의 전자빔 에너지와 $1{\times}10^{14}-1{\times}10^{16}electrons/cm^2$ dose를 사용하여 HEEBI 처리 되었다. IGZO 박막의 광 투과도는 utraviolet visible near-infrared spectrophotometer (UVVIS)로 측정되었다. HEEBI 처리 된 IGZO/유리 이중층의 총 광 투과도에서 HEEBI 처리된 IGZO 단일막 만의 광 투과도를 분리하는 방법을 상세히 연구하였다. 실험 결과로부터 $1{\times}10^{14}electrons/cm^2$의 적절한 dose로 처리된 HEEBI가 IGZO 박막의 투명도를 극대화시킴을 알 수 있었다. 또한 이렇게 적절한 dose로 처리된 HEEBI가 광학 밴드갭($E_g$)을 3.38 eV에서 3.31 eV로 감소시킴을 알 수 있었다. 이러한 $E_g$의 감소는 적절한 dose로 공기 중 상온에서 처리된 HEEBI가 진공 중 고온에서 처리된 열적 annealing 효과와 유사함을 제시하고 있다.

• 한국잡초학회지
• /
• 제8권1호
• /
• pp.15-22
• /
• 1988

본(本) 연구(硏究)는 큰달맞이꽃종자(種子)의 발아(發芽)에 미치는 광(光)의 생리적작용(生理的作用)을 파악(把握)하기 위하여 발아요인(發芽要因)들(광질(光質), 저온(低溫), 변온(變溫), 수분(水分), 산십(酸十), 종피(種皮) 등) 상호작용(相互作用)을 광(光)과 관련(關聯)하여 검토(檢討)하였다. 광(光)은 혐기조건(嫌氣條件) 및 낮은 water potential (-18bars) 하(下)에서도 발아초기(發芽初期) 단계(段階)를 유기(誘起)시키며 종피(種皮)보다는 비(飛)의 활력(活力)에 영향을 미쳐 발아율(發芽率)을 증가(增加)시켰다. 이러한 광(光)의 효과(效果)중 청색광(靑色光)처리에 의해서는 억제(抑制)되었다. 이는 가역적(可逆的) 반응(反應)을 보였으며 그 정도(程度)는 광(光)의 세기가 높고, 조사기간(照射期間)이 길수록 높은 경향(傾向)이었다. 저온(低溫), 변온(變溫), 종피연화처리(種皮軟化處理) 및 광(光) 등은 발아유기(發芽誘起)에 정(正)의 상호작용(相互作用)을 보였으나 단색광(單色光) 처리(處理)에서는 저온(低溫)의 발아유기효과(發芽誘起效果)를 오히려 저해(沮害)하는 경향(傾向)이었다. 기타 pH 용액(溶液) 및 $GA_3$ 용액(溶液)은 광(光) 및 암발아(暗發芽)와는 무관(無關)하였다.