• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.9
• /
• pp.780-789
• /
• 2007

Lock-on phenomenon in the wake of a circular cylinder is investigated at the Reynolds number of 360 using direct numerical simulation (DNS). To induce lock-on, a streamwise velocity perturbation with a frequency of twice the natural shedding frequency is superimposed on the free stream velocity. The Reynolds stress distributions are investigated to analyze the streamwise force balance acting on the recirculation region and the results are compared with the previous experimental result. When the lock-on occurs, the pressure force on the recirculation region is shown to increase mainly due to the reversal of the Reynolds shear stress distribution, which is consistent with our previous results using PIV measurement. It is also shown that, with the lock-on, the strength of the primary vortices increases whereas that of the secondary vortices decreases significantly. Further, under the lock-on condition the wavelength of the secondary vortices increases by as much as 2.5 times.

• 한국가시화정보학회:학술대회논문집
• /
• 2004.11a
• /
• pp.18-21
• /
• 2004

Lock-on characteristics of the flow around a circular cylinder performing a rotationally oscillation with a relatively high forcing frequency have been investigated experimentally using flow visualization and hot-wire measurements. Dominant parameters are Reynolds number (Re), amplitude of oscillation $(\theta_A)$, and frequency ratio $F_R=f_f\;/\;f_n$, where $f_f$ is the forcing frequency and if is the natural frequency of vortex shedding. Experiments were carried out under the conditions of $Re=4.14\times10^3,\;\pi/15\leq\theta_A\leq\pi/3$, and $F_R=1.0$. The effects of this active control technique on the lock-on flow regime of the cylinder wake were evaluated through wake velocity measurements and spectral analysis of hot-wire signals. The rotary oscillation modified the flow structure of near wake significantly. The lock-on phenomenon was found to occur in the range of frequency encompassing the natural vortex shedding frequency. In addition, when the amplitude of oscillation is less than a certain value, the lock-on phenomenon was occurred only at $F_R=1.0$. The lock-on range expanded and vortex formation length decreased as the amplitude of oscillation increases. The rotary oscillation generated small-scale vortex structure just near the cylinder surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.601-604
• /
• 2003

The magnetic field generated in the iron core, which is required for the magnetic field to link each coil of the flux-lock type reactor, affects the fault current limiting characteristics of the flux-lock type high-Tc superconducting fault current limiter(SFCL). By applying numerical analysis for equivalent circuit of flux-lock type SFCL, the magnetic field induced in the iron core including currents of each coil was investigated. Through the analysis of magnetic field, we have analyzed that the magnetic field linked the 3rd coil, which is wound in the iron core, prevents the saturation of the iron core, but decreases the impedance of the flux-lock type SFCL.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.3
• /
• pp.197-204
• /
• 2000

Tensile strength (stress) of bar splice is important in the research of mechanical behavior of reinforced concrete structures-beam, column etc.- with bar splice. The purpose of this research is to evaluate the flexural behavior - deflection of beam specimens, strain of main bars - of reinforced concrete beam with Lock Joint Coupler. To make a comparative research, reinforced concrete beam specimens with normal deformed bar and lap splice are tested and analyzed. Test results, Comparing a deflection of three types flexural specimens, a flexural specimen with Lock Joint Coupler is 40% greater than the other flexural specimens. At the center of flexural specimen, the strain of main bar(D29) with lock joint coupler is 50% less, and vice versa, at the point of 14cm far from the center of flexural specimen, the strain of main bar(D29) with lock joint coupler is 9% larger than the strain of main bar(D29) which calculated using the classical flexure theory. A discords, between a deflection behavior of the flexural specimens and a strain of the main bar, are caused by the difference of strain between the lock joint coupler and main bar, near the lock joint coupler. So, additional research is need to verify as stated above discords.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.289-289
• /
• 2008

We investigated the operational characteristics of the separated three-phase flux-lock type superconducting fault current limiter (SFCL). The single-phase lock type SFCL consist of two coils, which are wound in parallel through an iron core. The high-$T_c$ superconducting(HSTC) thin film connected in series with secondary coil. The separated three-phase flux-lock type SFCL consist of three single-phase flux-lock type SFCL. In a normal condition, the SFCL is not operate. When a fault occurs, the current of a HSTC thin film exceeds its critical current by fault current, the resistance of the HSTC thin film generated. Therefore fault current was limited by SFCL. The separated three-phase flux-lock type SFCL are operated in fault condition such as the the single line-to-ground fault, the double line-to-ground fault and the triple line-to-ground fault. The experimental results, the SFCL operational characteristics was dependent on fault condition.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.2
• /
• pp.73-79
• /
• 2011

This paper describes a reset-free delay-locked loop (DLL) for a memory controller application, with the aid of a hysteresis coarse lock detector. The coarse lock loop in the proposed DLL adjusts the delay between input and output clock within the pull-in range of the main loop phase detector. In addition, it monitors the main loop's lock status by dividing the input clock and counting its multiphase edges. Moreover, by using hysteresis, it controls the coarse lock range, thus reduces jitter. The proposed DLL neither suffers from harmonic lock and stuck problems nor needs an external reset or start-up signal. In a 0.13-${\mu}m$ CMOS process, post-layout simulation demonstrates that, even with a switching supply noise, the peak-to-peak jitter is less than 30 ps over the operating range of 500-1200 MHz. It occupies 0.04 $mm^2$ and dissipates 16.6 mW at 1.2 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.9
• /
• pp.1-7
• /
• 2004

This thesis shows embodiment of lock system design for combination of usefulness, convenient of Barcode and cellular phone. This thesis consists of Lock system design using cellular phone and product introduction, including details from formation of barcode scanner to scanner design. When this research is applied to security system a general idea of physical key disappears and it is Possible that cellular phone becomes the center of security and we can expect that cellular phone use for payment will increase due to mutual direction service. After, we should study its application to various practical field and develop high sensitive equipment.

• The Journal of Korean Society for Radiation Therapy
• /
• v.16 no.1
• /
• pp.67-72
• /
• 2004

Purpose : Patient immobilization is crucial factor for radiation therapy. Generally, we have been used vacuum bag immobilization device(Vac-Lock) for whole body immobilization. In order to easily set up of vacuum bag(Vac-Lock), we made a 3DCA(3-Dimensional Conformal Accessary). The purpose of this study is evaluation of effectiveness of 3DCA using Vack-Lock for patient immobilization. Materials and Methods : We made 3DCA(3-Dimensional Conformal Accessary) tool of wooden boards. The reasons to choice of wooden boards are its easily handling nature and cheap expenses. Results : (1) We reduced man power from $5{\sim}6$persons to 1person to make immobilizations, (2) Shortened work time from 1hour to within 10minutes. (3) Avoid a collision to treatment gantry head. (4) Its shapes are smart and clean. Conclusion : We have made and used 3DCA(3-Dimensional Conformal Accessary) tool was very effective and convenience for the patients and users.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.515-518
• /
• 2001

In this study, the electric door lock using the password input system for security improvement was fabricated. The security has been improved by using the multiple micro process. The controller with solenoid valve has been designed indirect driving system for releasing the door lock system. Also, the self checkup system for improving the trustworthy was developed with two kinds of micro process. The results will be applied IC card system and fingerprint identification system for security improvement.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.79-82
• /
• 2000

This paper describes a delay locked loop with selective starting point for use in a high-frequency systems. SSRDLL (selective starting point RDLL) has been simulated in a 0.25$\mu\textrm{m}$ standard n-well CMOS process parameter to realize a fast lock-on time. This DLL is shown to be insensitive to variations in PVTL. The simulated lock time of the proposed SSRDLL is within 4 clock cycles at 333㎒ clock input.