• 대한기계학회논문집
• /
• 제6권4호
• /
• pp.323-330
• /
• 1982

The vibration characteristics of continuous span periodically supported beams with moving loads are determined theoretically and experimentally. Moving loads are assumed to travel at constant acceleration with constant magnitude. Analyses by using the Fourier Transform technique are developed to determine the dynamic performance of moving load interacting with multiple and continuous beam. Equation of motion for the moving load is non-dimensionalized. Non-dimensional deflection proflies of continuous beam are presented in detail for the single concentrated moving load with constant acceleration. Experimental moving load and continuous beam models are developed. The maximum deflections at each midpoints 5,7 and 9 span beam are measured and their non-dimensional maximum deflections are presented. The non-dimensional maximum deflection of continuous beam is compared with measured maximum deflection of 9 span beam and found to agree reasonably well. The deflection of continuous beam due to moving load with acceleration is strongly influenced in the resonance region.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.54-59
• /
• 2006

An analytical solution for deflection-load characteristics of a conical disk spring used especially in the automotive manual transmission clutch applications is proposed in order to take into account the effects of friction and large deformation. The conical disk spring, or the diaphragm spring, has a hinge support, an application point of release load at the tip of the fingers and an application point of clamp load near but inside the outer perimeter of the conical disk spring. The friction coefficient is assumed to be a constant regardless of the speed of deflection and the magnitude of loads. Comparison with experimental shows a good agreement with the analytical prediction. Also, the sensitivity of the clamp load due to variations in the geometrical parameters of the conical disk spring is calculated and discussed.

• Journal of Biosystems Engineering
• /
• 제28권6호
• /
• pp.485-490
• /
• 2003

Flexural rigidity(EI) and deflection characteristics of rice stalks were studied to investigate the mechanical interaction between a rice stalk and a combine reel in harvesting. Deflection of a rice stalk caused by reel operation is so large that conventional equation of small deflection fer elastic beam cannot be applied to the study of deflection characteristics. Therefore, an equation of large deflection for elastic beam was introduced in this study. Feasibility of this equation was examined by comparing theoretical calculation with the measured results for piano wire, and by the relationship between deflection and load acting on a rice stalk which was presumed by this equation. Results showed that the large deflection equation could predict the measurement data quite well. From this research, the following results were obtained. 1. Flexural rigidity(EI) calculated from the equation of large deflection was 4.0${\times}$l0$^4$N$.$$\textrm{mm}^2$(diameter 1.4mm, deflection 300mm) while the actual EI value of a piano wire(diameter 1.4mm) was 3.9${\times}$10$^4$N$.$$\textrm{mm}^2$. 2. The relationship between deflection and load acting on a rice stalk could be presumed by the large deflection equation. Flexural rigidity values of tested rice stalks calculated from the equation of large deflection were 1.6∼2.4${\times}$ l0$^4$N$.$$\textrm{mm}^2$(Hwa sung), 2.7∼3.5${\times}$ l0$^4$N$.$$\textrm{mm}^2$(Il pum) and 1.7∼2.4${\times}$ l0$^4$N$.$$\textrm{mm}^2$(Damakum)

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.775-776
• /
• 2011

• 콘크리트학회지
• /
• 제9권1호
• /
• pp.183-194
• /
• 1997

통상적인 방법에 의해 측정된 콘크리트 보의 변위는 지지점의 국부변위나 변위의 측정 위치에 따른 외부적인 요인이 포함된다. 이러한 오류에 의한 변위의 크기는 실제 변위크기와 거의 같은 정도이기 때문에 이를 사용하여 정확한 파괴 파라메타를 구하기 어렵다. 본 연구에서는 외부적인 요인의 영향을 받지 않는 균열개구 변위와 하중작용 방향 변위의 상관관계를 규명하고, 하중 개구부 변위를 파괴특성을 구하는 인자로 사용하였다. 균열개구 변위와 하중방향 변위는 서로비례함을 알 수 있었으며, 이 비례관계를 이용하여 RILEM에서 제시한 파괴에너지 결정방법에 대한 문제점을 발견하였고 이에 대한 수정방법을 제시하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.97-103
• /
• 2002

Vibration isolation technology using an air spring and laminated rubber bearing is widely used because it has excellent vibration isolation characteristics. In the part of that, we usually make use of the self-damped air suing. It is occupied two chambers, restrictor, diaphragm and load plate. Two chambers contain compressed air and the volume of chambers and the area of load plate give a definition of stiffness and load. The restrictor and the volume ratio of two chambers give a definition of damping ratio. The conventional model of restrictor is made of one orifice and it causes turbulent flow in the orifice at the region of large deflection. The stillness of air suing is larger and the damping is lower in the region of large deflection. In the multi-orifice case, the stiffness is similar to air spring with one orifice but damping ratio is larger than conventional air spring. And damping ratio is smaller than conventional air suing in small deflection region. Deflection is small in the region of high frequency so small damping is better than large damping. As a result, we can reduce the storage stiffness of air suing in the wide region of deflection and increase the damping ratio in the region of large deflection. After this, we will try to and the relation of Reynolds Number and Flow Resistance then we are going to make another restrictor for air spring to improve damping ratio and stiffness.

• 오토저널
• /
• 제4권3호
• /
• pp.56-68
• /
• 1982

This paper presents analytic solutions of defection and their resonance diagrams for a uniform beam of infinite length subjected to an constant axial force and moving transverse load simultaneously. Steady solutions are obtained by a time-independent coordinate moving with the load. The supporting foundation includes damping effects. The influences of the axial force, the damping coefficient and the load velocity on the beam response are studied. The limiting cases of no damping and critical damping are also investigate. The profiles of the deflection of the beam are shown graphically for several values of the load speed, the axial force and damping parameters. Form the results, following conclusions have been reached. 1. The critical velocity .THETA.cr decreases as the axial compressive force increases, but increases as the axial tensile force increase. 2. At the critical velocity .THETA.cr the deflection have a tendency to decrease as the axial tensile force increases and to increase gradually as the axial compressive force increases. 3. In case if relatively small dampings, the deflection increases suddenly as the velocity of the moving load approaches the critical velocity, and it reachs its maximum at the critical velocity, and it decreases and become greatly affected by the axial force as the velocity increases further. 4. in case of relatively large dampings, as the velocity increases the deflection decreases gradually and it is affected little by the axial load.

• 한국자동차공학회논문집
• /
• 제3권5호
• /
• pp.1-9
• /
• 1995

The purpose of this study is to develop a computer simulation program for analyzing load transmission characteristics of a helical gear system in design stage. In this analysis, the rotational delay, load distribution, root stress, and contact area are investigated. That is, the influence function of deflection is obtained by finite element analysis and the influence function of approach and gear tooth error are considered. Load distribution, rotational delay, and contact area are calculated by solving load-deflection equation which includes these influence functions and tooth error, and the influence function of the bending moment is obtained by finite element analysis. The root stress is calculated by the load distribution and the influence function of the bending moment. The results of the simulation are cross-checked through a specially designed experimental set-up.

• 한국음향학회지
• /
• 제16권4호
• /
• pp.21-28
• /
• 1997

본 연구에서는 빈경하중과 축회전 속도를 변화시켜 가며 하중으로 인한 베어링의 부하-변위량 특성을 Harris 이론과 비교분석하였다. 실험결과 결함이 없는 경우 하중이 적을 때는 Harris이론과 비교적 잘 일치하나, 하중이 증가할 수록 구동축의 변곡, 볼베어링 하중의 불균형 등의 영향을 받아 이론값과 차이를 보였다. 반경방향 하중이 있는 단일결함과 다중결함의 경우 하중이 증가함에 따라 변위량의 변화는 축심변위량 보다 반경변위량이 더욱 커지게 된다는 것을 알았다. 베어링의 결함상태에 따라 하중과 변위량의 기울기인 부하-변위량 특성을 구함으로써 볼베어링의 결함유무를 검출하였다.

• 한국산학기술학회논문지
• /
• 제10권8호
• /
• pp.2032-2037
• /
• 2009

본 논문은 공용중인 교량구조물의 내하력 평가시 획일적이고 실제 거동특성을 적극적으로 활용하지 않아 발생할 수 있는 내하력 평가의 오류에 대하여 연구하였다. 내하력의 평가시 지점의 경계조건과 같은 현재의 거동특성을 반영하기 위하여 초기 결함을 갖는 부재에 대한 좌굴방정식에 처짐을 적용시켜 산정된 축방향력과 처짐에 의해 구해진 모멘트를 고려하여 교량의 내하력을 평가하였다. 기존의 내하력 평가시에 다소 획일적으로 적용되어지는 응력보정 계수를 좌굴방정식을 통하여 각 주형에 대하여 선 반영함으로서 내하력 평가의 오류를 다소 제거하고자 하였다.