• 산업경영시스템학회지
• /
• 제32권1호
• /
• pp.34-43
• /
• 2009

In this thesis, we explain developing processes of the power transmission system for lift truck. Conventional power transmission system had some problems such as spatial constraints or low speed and high torque problem. Because conventional power transmission system was mainly designed for high speed vehicles. In this paper we developed power shift drive axle specialized for $2.0{\sim}3.5$ ton lift truck. Innovative structure of transmission which is built in inside axle, enables to reduce system weight and size by 40% compared to the conventional power transmission system. Also, it is possible to do additional functions such as auto parking system and anti-roll back system.

• 한국소음진동공학회논문집
• /
• 제27권1호
• /
• pp.28-35
• /
• 2017

최근 기존의 유압 차량 리프트는 높이제어의 어려움으로 인해 기술개발의 한계에 직면하였다. 휠 얼라이먼트나 차량의 하중 분포에 따른 미세한 불규칙적인 변형을 보상하기 위해서는 매우 정밀한 위치 제어성이 요구되고 있다. 이 연구에서는 이러한 기존 리프트 시스템의 한계를 해결하고자 매우 정교한 압력강하를 이끌어낼 수 있는 MR 밸브 시스템을 활용하여 새로운 차량 리프트를 제안하고 이에 대한 분석을 진행한다. 우선적으로 MR 밸브의 요구되는 성능을 파악하기 위해 유압 리프트의 운동방정식을 설립하고, 요구되는 압력강하를 얻기 위해 MR 밸브를 설계한다. 또한 정밀한 위치 제어 성능을 얻기 위해 PID 제어기를 설립하고, 시뮬레이션을 통해 제안된 시스템의 제어성을 검증한다.

• 전자공학회논문지B
• /
• 제30B권2호
• /
• pp.1-7
• /
• 1993

In this paper, we show that Petri nets can be applied to design and reliability analysis of concurrent, parallel and embedded mode system such as a lift system that is familiar to our daily life. Modeling the behavioral characteristics of the lift system we extend the standard Petri nets by nadditionally constant timed transition, fault transition, stochastic imed ttransition and conditional transition concepts. Likewise, we present esults of rdesign and analysis of the system. This method can be applied to esign and danalysis of any other concurrent systems.

• 항공우주시스템공학회지
• /
• 제7권3호
• /
• pp.1-6
• /
• 2013

Numerical optimization of two dimensional high lift configuration was performed with flow solver and optimization method based on RSM(Response Surface Model). Navier-Stokes solver with Spalart-Allmaras turbulence model was selected for the simulation of highly complex and separated flows on the flap. For the simultaneous optimization of both flap shape and setting (gap/overlap), 10 design variables (eight variables for flap shape variation and two variables for flap setting) were chosen. In order to generate the response surface model, 128 experimental points were selected for 10 design variables. The objective function considering maximum lift coefficient, lift to drag ratio and lift coefficient at specific angle of attack was selected to reduce flow separation on the flap surface. The present method was applied to two dimensional fowler flap in landing configuration. After applying the present method, it was shown that the optimized high lift configuration had less flow separation on the flap surface and lift to drag ratio was suppressed over entire angle of attack range.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.1091-1097
• /
• 1991

A logical and systematic procedure to derive a mathematical model for magnetically levitation(maglev) systems with a combined lift and guidance is developed by using and graph. First, bond graph is constructed for the energy-feeding system with magnetic leakage flux. And, the overall maglev system in which lift and guidance dynamics are coupled is modeled by using the concept of multi-port field in bond notations. Finally, the LQG/LTR control systems are designed for single-input single-output and for multi-input multi-output maglev systems. In this paper, it has been shown that the bond graph is an excellent method for modeling multi-energy domain systems such as maglev systems and the multivariable control system is required to improve the performance of the maglev system with a combined lift and guidance.

• Journal of Power Electronics
• /
• 제9권6호
• /
• pp.854-865
• /
• 2009

Super-lift dc-dc converters are a series of advanced step-up dc-dc topologies that provide high voltage transfer gains by super-lift techniques. This paper presents a developed graphical modelling method for super-lift converters and gives a thorough analysis with a consideration of the effects caused by parasitic parameters and diodes' forward voltage drop. The general guidelines for constructing and deriving graphical models are provided for system analysis. By applying it to examples, the proposed method shows the advantages of high convenience and feasibility. Both the circuit simulation and experimental results are given to support the theoretical analysis.

• 한국자동차공학회논문집
• /
• 제16권3호
• /
• pp.80-86
• /
• 2008

Recently, controlled auto ignition(CAI) in gasoline engines are drawing more attentions due to its extremely low level of NOx emissions and potentials in lowering the fuel consumption rate. The one of the key techniques for realizing CAI combustion in engines is the control of valve system. Since the valve linkage system with higher complexity, or even earn-less valve systems, such as electro-hydraulic and electro-magnetic system, are adopted in CAI engines, it is not easy to estimate the valve lift profile from earn profiles. Therefore new measurement techniques for valve lift in CAI engines have been tried and tested. In this paper, hole type valve lift sensor was developed and tested to check the applicability in CAI engines. The valve lifts could be obtained from the sensor signal, which depends on the distance from the sensor to magnet attached to valve. Various engine speeds, ranging from 2,000 to 6,000 rpm, and valve lifts, maximum up to 9.7 mm, were tested. It was found that the sensor output for valve lift had accuracy of 98% in comparison with the basic specifications of valve lift through improvements of sensor driving circuit.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.6-7
• /
• 2018

Although the importance of the construction lift is increasing, no improvements are being made to its operating system. This study proposed an optimal call-response algorithm of the construction lift for high-rise building construction by using image sensing technology, height measuring sensor, and load cell. This algorithm makes turn-around decision of the construction lift by considering the information and the number of user. It occurs when the call comes from a floor where the construction lift already have passed. The purpose of this study is to reduce the total latency of the construction lift user. Furthermore, it is possible to prevent delay in construction duration by carrying out a priority operation of the construction lift for the critical workforce.

• Journal of Biosystems Engineering
• /
• 제31권3호
• /
• pp.182-187
• /
• 2006

Aerial application using an unmanned agricultural helicopter can reduce labor and pollution. The development of an agricultural helicopter became urgent for both precise and timely spraying. In this study, a rotor system for unmanned helicopter capable of 20 $kg_f$ payload, was developed and lift capability was evaluated. A lift force over the dead weight of the helicopter was obtained at the pitch angle of $6^{\circ}$. As the pitch angle increased to $8^{\circ}\;and\;10^{\circ}$, the total lift increased to $74{\sim}81\;kg_f\;and\;86{\sim}93\;kg_f$, respectively. A range of engine speed at the rated flight condition, lifting mean payload of 23 $kg_f$ was determined. The data acquired from this study will be used for designing tail system and RF console in the next stage of the research. The rated lift capability was enough for loading 20 liters of spray material including spraying equipments.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.123-131
• /
• 2006

The majority of pedestrian fatalities and injuries are caused by vehicle-pedestrian accidents. Recently, it has been recognized as a serious problem. Injuries of occupants in a vehicle have been decreased considerably. However, efforts for protection of pedestrians are still insufficient. These days, many advanced industries are striving for a better protection of pedestrians by using an active hood lift system, rather than reforming the existing structure. In this research, the active hood lift system is designed to enhance the performance for protection. The active hood lift system is analyzed by using the nonlinear finite element method. An optimization problem is formulated by incorporation of the analysis results. Orthogonal arrays are utilized to solve the formulated problem. An iterative optimization algothrithm using orthogonal arrays is utilized for design in the discrete space. It is found that the method can remarkably decrease the number of function evaluations.