• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.7
• /
• pp.625-631
• /
• 2010

This paper proposes lane recognition algorithm using lane prominence technique to extract lane candidate. The lane prominence technique is combined with embossing effect, lane thickness check, and lane extraction using mask. The proposed lane recognition algorithm consists of preprocessing, lane candidate extraction and lane recognition. First, preprocessing is executed, which includes gray image acquisition, inverse perspective transform and gaussian blur. Second, lane candidate is extracted by using lane prominence technique. Finally, lane is recognized by using hough transform and least square method. To evaluate the proposed lane recognition algorithm, this algorithm was applied to the detection of lanes in the rainy and night day. The experiment results showed that the proposed algorithm can recognize lane in various environment. It means that the algorithm can be applied to lane recognition to drive unmanned vehicles.

• International Journal of Highway Engineering
• /
• v.20 no.1
• /
• pp.117-126
• /
• 2018

PURPOSES : The purpose of this paper is to analyze the change in lane reflection performance through lane washing and sweeping on highway lanes. METHODS : This paper compared and analyzed the changes in lane reflection performance before and after lane washing and sweeping. The research method was as follows. First, we selected four research sites on the Gyeong-bu Highway. Second, the parameters affecting lane reflection performance are classified into luminance, brightness, and number of glass beads. Third, the change in reflection performance was measured after washing /sweeping at the same place after studying 60m of the unwashed/unswept area. Fourth, the measurement results were compared and analyzed before and after lane washing/sweeping. RESULTS : The results of this study are as follows. First, lane washing improved the luminance and brightness by 4.2~21.4% and 1.4~5.1%, respectively, and reduced the number of glass beads per wash by 0.2~1.2%. Second, lane sweeping improved the luminance and brightness by 2.3~8.5% and 0.8~2.3%, respectively, and reduced the number of glass beads per sweep by 0.8~4.9%. CONCLUSIONS : By comparing the results of lane washing and sweeping, it was found that compared to lane sweeping, lane washing improved the luminance and fewer glass beads were dropped.

• International Journal of Highway Engineering
• /
• v.16 no.1
• /
• pp.41-48
• /
• 2014

PURPOSES : The lane width of the domestic highway is 3.5 ~ 3.6m and it has been designed nationwide. However, the distribution of the average vehicle widths, rearview mirror widths and lateral wheel paths by region appear different. Then, lane spare widths may differ by region followingly. Thus, the flexible design of freeway lane widths is required. METHODS : The methodologies of this paper are as follows. First, vehicle widths rearview mirror widths lateral wheel paths of vehicles driven four national expressways were measured. Second, lane spare widths by vehicle widths were calculated. Third, lane spare widths reflecting rearview mirror widths were calculated by using interval estimation. Additionally, lane spare widths reflecting vehicles lateral wheel paths were calculated. RESULTS : The results of this paper are as follows. First, lane spare widths by vehicle widths ranges 0.83 to 0.95m. Second, lane spare widths reflecting rearview mirror widths ranges 0.518 to 0.747m at the confidence interval 95%. Third, lane spare widths reflecting vehicles' lateral wheel paths ranges -0.022 to 0.322m at the curved sections and the confidence interval 95%. CONCLUSIONS : It may be concluded that the present lane spare widths are relatively narrow at the curved section. Thus, there is a need to consider expanded lane widths at the curved sections. Additionally, there is a need to consider flexible design of lane widths by various conditions.

• International Journal of Highway Engineering
• /
• v.18 no.3
• /
• pp.87-94
• /
• 2016

PURPOSES : This study analyzed the lane-by-lane traffic flow characteristics in Korea by using real-world data, including congestion levels, for 2-, 3-, and 4-lane freeways. METHODS : On the basis of a literature review, lane flow and speed characteristics were analyzed using flow measurements and speed ratios. In addition, the effect of congestion levels on traffic flow were visualized using rescaled cumulative plots. RESULTS : Driver behavior varied depending on the congestion level. During free-flow conditions, the lane-use ratio of individual lanes varied largely, whereas during congestion, the ratio was nearly the same for all lanes (i.e., equilibrium). During maximum-flow and congestion conditions, the median lane was used more than the shoulder lane, whereas during all other conditions, the shoulder lane had a higher lane-use ratio. In 3- or 4-lane freeways, the lane-use ratio of the median lane always exceeded 1 and was the highest during free-flow conditions. CONCLUSIONS : The results of the present analysis can be used as an index to predict congestion before a lane is overcapacitated. Moreover, the results can be applied in variable lane guidance systems, such as car navigation systems and variable message displays, to control traffic flow.

• ETRI Journal
• /
• v.36 no.6
• /
• pp.1066-1069
• /
• 2014

We propose a lane adaptive recovery scheme for multiple lane faults in a multi-lane-based Ethernet link. In our scheme, when lane faults occur in a link, they are processed not as full link faults but as partial link faults. Our scheme provides a higher link utilization and lower packet loss rate by reusing the available lanes of the link and providing a low recovery time of under a microsecond.

• 한국HCI학회:학술대회논문집
• /
• 2008.02a
• /
• pp.205-209
• /
• 2008

Recently, for development of hardware systems, it has been comercially developed for lane detection system of assistive funtion to drivers. There are so many driving systems that is capable of detecting lane for ideal environment like quite visible lane and sweep curve just like highway, but these kinds of system are hard to apply for self driving system because it is difficult to detect lane in dynamic environment, which have rapid curve or only one sided lane For this paper, we proposed intelligent driving system that is able to detect the lane in case of rapid curve by labeling, or one sided lane by lane prediction. based on experimental results, we prove our lane detection system is able to detect lane not only in ideal environment, but also environment which have rapid curve or one sided lane.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.142-149
• /
• 2015

Most of the mono-camera based lane detection systems are fragile on poor illumination conditions. In order to compensate limitations of single sensor utilization, lane information fusion system using multiple lane sensors is an alternative to stabilize performance and guarantee high precision. However, conventional fusion schemes, which only concerns object detection, are inappropriate to apply to the lane information fusion. Even few studies considering lane information fusion have dealt with limited aids on back-up sensor or omitted cases of asynchronous multi-rate and coverage. In this paper, we propose a lane information fusion scheme utilizing multiple lane sensors with different coverage and cycle. The precise lane information fusion is achieved by the proposed fusion framework which considers individual ranging capability and processing time of diverse types of lane sensors. In addition, a novel lane estimation model is proposed to synchronize multi-rate sensors precisely by up-sampling spare lane information signals. Through quantitative vehicle-level experiments with around view monitoring system and frontal camera system, we demonstrate the robustness of the proposed lane fusion scheme.

• KIPS Transactions on Software and Data Engineering
• /
• v.3 no.7
• /
• pp.277-284
• /
• 2014

The detection method of curves for the lanes which is powerful for the variation by utilizing the lane variation vector and cardinal spline on the inverse perspective transformation screen images which do not required the camera parameters are suggested in this paper. This method detects the lane area by setting the expected lane area in the s frame and next s+1 frame where the inverse perspective transformation and entire process of the lane filter are adapted, and expects the points of lane location in the next frames with the lane variation vector calculation from the detected lane areas. The scan area is set from the nextly expected lane position and new lane positions are detected within these areas, and the lane variation vectors are renewed with the detected lane position and the lanes are detected with application of cardinal spline for the control points inside the lane areas. The suggested method is a powerful method for curved lane detection, but it was adopted to the linear lanes too. It showed an excellent lane detection speed of about 20ms in processing a frame.

• Journal of Korean Society of Transportation
• /
• v.31 no.4
• /
• pp.32-46
• /
• 2013

Because of short length between interchanges, traffic congestion has been caused by a lot of short trip traffic in the urban section of interregional expressway. Also, in case of expressway with Bus Only Lane, bus causes dangerous situation by conflicting between vehicles and buses in order to access from Bus Only Lane to IC. Therefore, this study aims to propose Express Lane applied by Bus Only Lane as a new lane operation in order to efficiently operate and to analyze the effectiveness on constructing Express Lane to the Pangyo-Hannam section in Gyeongbu Expressway. The study analyzes effectiveness by scenario using the micro traffic simulation tool, VISSIM 5.4. For this, the indicators which evaluate construction effect of Express Lane, are used by average delay time, average speed and total travel time. The results of the study showed the best effectiveness when Express Lane installed one, and it represented an ideal traffic condition when long distance trip traffic of the whole traffic is 25% in the study section. Therefore, the construction of Express Lane using Bus Only Lane achieves positive effectiveness on safety and expense aspect as well as uncongested flow.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.222-228
• /
• 2003

Lane departure avoidance system is one of the key technologies for the future active-safety passenger cars. The lane departure avoidance system is composed of two subsystems; lane sensing algorithm and active-steering controller. In this paper, the road image is obtained by vision sensor and the lane parameters are estimated using image processing and Kalman Filter technique. The active-steering controller is designed to prevent the lane departure. The developed active-steering controller can be realized by steer-by-wire actuator. The lane-sensing algorithm and active-steering controller are implemented into the steering HILS(Hardware-In-the-Loop Simulation) and their performance is evaluated with a human driver in the loop.