• Journal of the Korean Wood Science and Technology
• /
• v.42 no.3
• /
• pp.282-289
• /
• 2014

After being laminated with a combination of glass fiber reinforced plastic and plywood, the GFRP laminated plate was densificated for 1 hour at $150^{\circ}C$ with pressure of $1.96N/mm^2$. A partial reinforced beam was produced by attaching the 5 GFRP laminated plates to the joint of glulam and the column. In addition, the column to beam joint was produced by using reinforced laminated wooden pin which was made of GFRP sheet and plywood, fiber glass reinforced cylindrical-LVL column. The joint was made of round log, glulam and drift pin as the reference specimen, and its moment resistance was evaluated. As a result, the strength performance of specimens with partial reinforced beams were 1.8 times stronger than the reference specimen on average. Furthermore, rupture was neither occurred on partial reinforced beam nor column. Toughness and stiffness of joints were also fine. The GFRP sheet reinforced laminated plate showed better reinforcement effect than GFRP textile reinforced one. GFRP sheet was inserted into each layer of laminate, and it showed good condition in rotation-angle and strength, therefore it is the most appropriate to reinforce the part of the beam.

• Journal of the Korea Furniture Society
• /
• v.17 no.1
• /
• pp.83-89
• /
• 2006

Because the surface of pine wood is very soft, there have been many attempts, like as surface coating, resin impregnation, and densificationt, to harden the surface of wood for its interior use. This study was carried out for surface hardening of pine wood by laminating of melamine resin sheet. The effect of laminating method on the characteristics of melamine resin sheet-laminated wood(MLW) was investigated. Flat-sawn softwoods were suitable for MLW making. And the pre-drying of wood at $105^{\circ}C$ for 30min, before laminating, was effective for preparing of defect-free MLW. The abrasion resistance of pine wood was greatly improved by laminating of melamine resin sheet on its surface. Consequently, the laminating of melamine resin sheet was proved to be a favorable method for improvement of surface abrasiveness of pine wood.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.1
• /
• pp.53-61
• /
• 2017

In this study, specimens were produced with a column member and a wooden gusset only by inserting an wooden gusset which is a substitute for steel plate into the center of a slit-processed column member. The moment resistance performance of the specimens was compared with that of control specimens that used a steel plate. The measured maximum moments of the specimens produced with GFRP-reinforced wooden laminated gussets and pins were lower by 24% on average compared to the steel plate-inserted specimens, but they showed good toughness. The fracture shape suggests that it was fractured along the annual rings between the pin and the end of the column member. The rigid specimen that integrated a laminated wood and a wooden laminated gusset with adhesive showed 2.8 times greater initial rigidity and 40% greater maximum moment on average compared to the control specimen. The rigid specimens mainly fractured on a glulam around glue line.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.6
• /
• pp.907-916
• /
• 2020

This research was conducted to investigate the linear expansion and resistance properties of a composite board (com-ply). This board was made of medium-density fiberboard (MDF) laminated using avocado (Persea americana), mahogany (Swietenia mahogani), and pine (Pinus merkusii) veneers. These three types of veneers were laminated on both surfaces of the MDF using adhesives, namely, epoxy and isocyanate. Glue (250 g·m^-2) was spread on the surface, followed by cold press for 3 h with an applied pressure of 15 kg·cm^-2. The research result revealed that com-ply exhibited an increased dimensional stability compared with MDF, indicated by reduction in water absorption, thickness swelling, and linear expansion. The com-ply made of the pine veneer and isocyanate adhesive exhibited high density, water absorption, thickness swelling, and screw withdrawal load. The com-ply that exhibited the strongest resistance to drywood termite attacks was the one made of the mahogany veneer and isocyanate adhesive. Moreover, the com-ply that exhibited the biggest weight loss (3.6 %) was made of the pine veneer and epoxy adhesive. The results of this research may facilitate in manufacturing com-ply using the selected veneer and adhesive without the application of hot press.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06a
• /
• pp.91-98
• /
• 2006

The purpose of this study is to investigate the opacity and printing strength of MG paper overlaid plywood. The printing strength of ink on MG paper can be evaluated effectively by a formula $E^{*2}=[(L^{*})^{2}+(a^{*})^{2}+(b^{*})^{2}]^{1/2}$ that we proposed. Higher E value indicates good printing strength of ink-on-paper. We also assess the real color of translucent printed MG paper with a formula CIE ${\bigtriangleup}E^{*}$ (color difference between a pile of same paper to be opaque and fancy paper laminated board). In addition, the color difference on paper surface caused by the color of wood-based board (bottom) can be evaluated by a formula of Pc. No. Generally, an acceptable appearance quality of fancy boards is ${\bigtriangleup}E^{*}$ <2.0 and small Pc.No. value. The experimental results showed that Japan-made MG papers -J1, J2 and J3 have better printing strength and gloss than that of Taiwan-made paper (T1). The reason for this was that Taiwan-made paper has poor printing strength and low gloss, which might be correlated to the fiber compositions in paper. Higher printing strength can be seen for short fiber containing handsheets when comparing to that of handsheets. Nonetheless, low-freeness sheets gives better printing strength than that of high-freeness sheets. High-opacity MG paper gives good opacifying effect to the fancy paper laminated wood-based boards. Comparing the surface color of 2 kinds of fancy paper laminated boards, paperboard T1 laminated with high-opacity fancy paper showed slight color difference. The same results can be seen for $??g/m^{2}$ handsheets. Higher-opacity Acacia and Eucalyptus bleached sulfate pulps (short fiber) gives higher opacifying effect on the plywood when comparing to Northan pine and Radiata pine sulfate pulps(long fiber). The former ones also showed small color differences when comparing the color differences between the color of fancy paper and laminated paper board. Additionally, the color of bottom plywood can't be shown through for the high-opacify surface paper adhered to. Besides, the PC No of the base paper laminated board is small as well. Apparently, we can add colorants to the binders for the manufscture of various handsheets ($30g/m^{2}$) with various pulp mix ratios to increase the opacity of paperboards to certain extents. When we using yellow and brown binders in paper laminated board, the color difference between Acacia and Eucalyptus handsheets overlaid boards decreasing to 2.0 (acceptable ${\bigtriangleup}E^{*}$ <2.0, hard to discern), but not much improvement for Northern and Radiata pines. Definitely, show-through defects can be discernible for lower opacity papers. In general, admirable printing strength of fancy paper by which glued to plywood can be made with high-opacity paper and colored binders techniques.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.3
• /
• pp.258-265
• /
• 2014

By replacing the previous metal connector on the joints of timber structure, the GFRP reinforced laminated wooden pin was produced using a wooden material and Glass fiber reinforced plastic(GFRP) composite laminate. In addition, using the reinforced wooden pin, the tensile type shear strength test was conducted. Based on the result of the bending strength test of the reinforced laminated wooden pin according to the GFRP arrangement, a specimen(Type-A) with a single insertion of GFRP for each layer have shown the most favorable performance. Also, it was verified that densified specimen hot pressed for an hour at the temperature of $150^{\circ}C$ and with the oppression pressure $1.96N/mm^2$ have shown the improved performance of 1.57 times than the specimen without the densification. And in the bending strength test considering the load direction, edgewise have shown a higher performance of 3.51 times than the flatwise. A shear strength test was conducted using the Type-A reinforced laminated wooden pin which have shown a moderate performance on the test. Based on the test conducted by differentiating the type of the joint plate and the connector, compared to the specimen(Type-DS) applied with the drift pin and steel plate, the specimen( Type-WL) applied with the GFRP reinforced laminated wooden pin and GFRP reinforced wooden laminated plate have shown 1.12 times higher shear strength and also have shown an excellent toughness even after the maximum load.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.1
• /
• pp.40-47
• /
• 2016

Instead of metal connector generally used on the structural glued laminated timber rahmen joints, the GFRP reinforced laminated plates combining veneer and GFRP (Glass Fiber Reinforced Plastic) and bonded type GFRP rod were used as the connectors. As a result of moment resistance performance evaluation on the joint part applied with these connectors, the yield moment of specimen using the GFRP reinforced laminated plates and GFRP rod pin was measured 4 % lower in comparison to the specimen (Type-1) using the metal connectors, but the initial rotational stiffness was measured 29% higher. Also, the yield moment and rotational stiffness of the specimen using the GFRP-reinforced laminated plates and wood (Eucalyptus marginata) pin showed were measured 11% and 56% higher in comparison to the Type-1 specimen, showing the best performance. It was also confirmed through the failure shape and perfect elasto-plasticity analysis that it showed ductility behavior, not brittle fracture, from the shear resisting force by the pin and the bonding strength increased and the unification of member was carried out. On the other hand, in case of the specimen bonded with GFRP rod, it was impossible to measure the bonding performance or it was measured very low due to poor bonding.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.1
• /
• pp.30-39
• /
• 2016

The evaluation of the lateral load performance for larch glulam portal frames was carried out using glass fiber reinforced plastic (GFRP) as connector in two different systems: the GFRP-reinforced laminated plates combined with veneer, and GFRP rod joints glued with epoxy resins to replace usual metal connectors for the structural glulam rahmen joints. As a result the yield strength, ultimate strength, initial stiffness of glulams of GFRP rod joints glued with epoxy resin decreased to 49%, 52% and 61% compared to those of the conventional metal connector. This connector will be a stress device where the bonding strength between the GFRP rod and glued laminated timber is important. Thus, there will be a high possibility that a problem may occur when it is applied to the field. On the other hand, the GFRP-reinforced laminated plates and wood (Eucalyptus marginata) pin were measured all within 3% for all measurements of the yield strength, ultimate strength, initial strength and ductility factor, regardless of high cross sectional loss on the glued laminated timber slit joint. In addition, the variation of stiffness on the cycle was 35%, which was the lowest, confirming that it was almost the same performance as the specimen prepared with the metal connector.

• Journal of agriculture & life science
• /
• v.46 no.1
• /
• pp.29-34
• /
• 2012

To examine possibilities to make use of woodceramics for the lower material of hot-floored ondol boards, woodceramics made from sawdust board with Pinus densiflora, put them in a wood frame and concrete block and heated them sending an electric current, and measured changes in surface temperature of a laminated floor board and a plywood floor board. As the sending an electric current to time passed, their surface temperature increased rapidly up to 20 minutes, and then gradually ascended. In terms of the surface temperature in the wood frame, the beginning temperature of a plywood floor board was higher than that of laminated floor one; however, as time passed, a laminated floor board's temperature rose, and after 60 minutes, it showed similar to the temperature of a floor board of lamination. On the other hand, the surface temperature in a concrete block showed that the laminated floor board was higher than the plywood floor board in both early and 60-minute later temperatures. With the lapse of time after switching off, the surface temperature of floor boards slowly dwindled up to 9 minutes, and from that time on, began to drop sharply. In terms of the descent speed of surface temperature, when woodceramics' surface temperature was adjusted at $70^{\circ}C$, the laminated floor board was the highest; when it was at $80^{\circ}C$, the plywood floor board was the highest, resulting in rapid descent speed of heat.

• Journal of the Korea Furniture Society
• /
• v.24 no.1
• /
• pp.79-87
• /
• 2013

The objective of this study was to increase the utilizability of domestic thinning and small diameter wood as applying in pattern design which can be applied in interior decoration, wood craft and wood furniture, and in developing the designs of furniture and household items. Then we investigated the physical and mechanical characteristics of Acer mono wood by pressurization and heat treatment. Color change is clear, and the wood density is increased with increasing pressing rate. The compressive and bending strengths are decreased as heating time is increased after pressing. However, shrinkage is improved after pressing and heating.