• Journal of the Korean Solar Energy Society
• /
• v.36 no.4
• /
• pp.41-47
• /
• 2016

A bypass diode is connected in parallel to solar cells with opposite polarity. The advantage of using the bypass diode is circumvented a destructive efforts of hot-spot heating in the photovoltaic(PV) module. In addition, it is possible to reduce a energy loss under the partial shading on the PV module. This paper presents a characteristic of photovoltaic module under partial shading condition and with defective bypass diode by using the experimental data. The results of field testing for each photovoltaic modules, when photovoltaic system which is connected power grid is operating, the inner junction-box temperature of shading photovoltaic module is high $5^{\circ}C$ because of difference of flowing current through into bypass diode. And incase of not operating photovoltaic system, the inner junction-box temperature of module with defective bypass diode is greatly higher than partial shading PV module.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.5
• /
• pp.42-49
• /
• 2007

This paper introduces a study on reliability-driven device placement using simulated annealing algorithm which can be applicable to MCM or electronic systems embedded in a spacecraft running at thermal conduction environment. Reliability of the unit's has been predicted with the devices' junction temperatures calculated from FDM solver and optimized by simulated annealing algorithm. Simulated annealing in this paper adopts swapping devices method as a perturbation. This paper describes and compares the optimization simulation results with respect to two objective functions: minimization of failure rate and minimization of average junction temperature. Annealing temperature variation simulation case and equilibrium coefficient variation simulation case are also presented at the two respective objective functions. This paper proposes a new approach for reliability optimization of MCM and electronic systems considering those simulation results.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.2
• /
• pp.208-213
• /
• 2008

In order to assess the reliability of the electronics control unit for vehicles, accelerated life test model and procedure are developed. By using this method, failure mechanism and life distribution are analyzed. The main results are as follows : i) the main failure mechanism is degradation failure that is, junction destruction of a semiconductor resin by high temperature. ii) the life distribution of the electronics control unit for vehicles is fitted well to Weibull life distribution and the accelerated life model of that is fitted well to Arrhenius model. iii) at the result of the life distribution, accelerated life test method is developed, and test time for life assessment will be shortened by 5,000 hours by this test method.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.11
• /
• pp.37-47
• /
• 1997

Utilizing 2-dimensional device simulations incorporating lattic eheating models, we analyzed in detail the DC breakdown characterisics of NMOS trasistors with different structures, which are commonly used as ESD protection transistors. The mechanism leading to device failure resulting from electrostatic discharge was explained by analyzing the 1st and 2nd breakdown characteristics of LDD devices. Also a criteria for more robust designs of NMOS transistor structures against ESD was suggested by examining the characteristics changes with changes in structural parameters such as the LDD doping concentration, the drain junction depth, the distance between source/drain contacts, and the source junction area.

• Journal of Chest Surgery
• /
• v.28 no.12
• /
• pp.1144-1149
• /
• 1995

Adenocarcinoma involving esophago-gastric junction[EGJ is usually originated from the gastric cardia and it presents unique clinical manifestations, requires special surgical care, and bears a much poor prognosis. We analyse the clinical data of 109 adenocarcinoma involving EGJ operated between August, 1987 and March, 1994. Curative resection of primary tumor including esophagus and lymph node dissection was possible on 102 cases[93.5% . Among these cases, 89 cases were advanced state over the stage III. The operative mortality was 1.8% and postoperative morbidity was 16.5%. The overall 3 year and 5 year survival rate was 48.5%, 34.1% each, and median survival was 27.5 month in the curative resected cases. The treatment failure was mainly distant metastsis including lymph node, except one local recurrence.Among many factors influencing long term results of resected adenocarcinoma involving EGJ, the only effort a surgeon can make is to attain completeness of tumor removal by dissecting all involved lymph node and ensuring adequate tumor free margins of both esophageal and cardiac side.

• Journal of Korean Neurosurgical Society
• /
• v.40 no.4
• /
• pp.249-255
• /
• 2006

Objective : This study is to evaluate the efficacy of dorsal short-segment fixation in unstable thoracolumbar junction fractures. Methods : The cases of 20 patients who underwent dorsal short-segment fixation were reviewed retrospectively. Clinical outcomes were analysed using Sonntag's pain level, work status, and neurological scale according to the modified Frankel classification. Radiological outcomes were analysed using Mumford's anterior body compression[%], canal compromise ratio, and Cobb's kyphotic angle. Results : At the latest clinical follow-up [average=14.6 months]. there were 19 [95.0%] in group I and 1 patient [5.0%] in II in pain level. The postoperative work status were 17 [85.0%] in group I, 2 patients [10.0%] in II, and 1 patient [5.0%] in V. Surgery brought to improve the neurologic status. In success group [19 cases, 95%], the average canal compromise ratio was reduced from 0.57 [${\pm}0.07$] to 0.05 [${\pm}0.08$] [P<005], the average anterior body compression [%] was reduced from 41% [${\pm}17$] to 18% [${\pm}14$] [P<0.05], and the average preoperative kyphotic angle was $20.0^{\circ}$ [${\pm}9.0$], and corrected to $5.7^{\circ}$ [${\pm}7.1$] postoperatively, and progressed to $7.8^{\circ}$ [${\pm}6.2$] at the latest follow-up. There was a case of implantation failure in an elderly osteoporotic patient. Conclusion : Although there are limitations in the patient number and follow-up period, the present study favors dorsal short-segment fixation for selective cases in unstable thoracolumbar junction fractures.

• Steel and Composite Structures
• /
• v.6 no.1
• /
• pp.71-85
• /
• 2006

This paper presents the results of a series of tests carried out on cold-formed steel rectangular hollow and concrete infilled beam to column connections and frames. A stub column was chosen such that overall buckling does not influence the connection behaviour. The beam chosen was a short-span cantilever with a concentrated load applied at the free end. The beam was connected to the columns along the strong and weak axes of columns and these connections were tested to failure. Twelve experiments were conducted on cold-formed steel direct welded tubular beam to column connections and twelve experiments on connections with concrete infilled column subjected to monotonic loading. In all the experiments conducted, the stiffness of the connection, the ductility characteristics and the moment rotation behaviour were studied. The dominant mode of failure in hollow section connections was chord face yielding and not weld failure. Provision of concrete infill increases the stiffness and the ultimate moment carrying capacity substantially, irrespective of the axis of loading of the column. Weld failure and bearing failure due to transverse compression occurred in connections with concrete infilled columns. Six single-bay two storied frames both with and without concrete infill, and columns loaded along the major and minor axes were tested to failure. Concentrated load was applied at the midspan of first floor beam. The change in behaviour of the frame due to provision of infill in the column and in the entire frame was compared with hollow frames. Failure of the weld at the junction of the beam occurred for frames with infilled columns. Design expressions are suggested for the yielding of the column face in hollow sections and bearing failure in infilled columns which closely predicted the experimental failure loads.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.6 no.2
• /
• pp.192-196
• /
• 2003

Angiodysplasia is the most common vascular abnormality of the gastrointestinal tract and probably the most frequent cause of recurrent lower intestinal bleeding in otherwise healthy elderly patients. Also, it is an important cause of hemorrhage in chronic renal failure observed in up to 19~32% of patients. Bleeding due to gastric angiodysplasia is treated by various endoscopic approaches, including argon and Nd : YAG laser photocoagulation, monopolar or bipolar electrocoagulation, heater probe, injection sclerotherapy, band ligation or hemoclipping. A 15-year-old boy, who had undergone hemodialysis for chronic renal failure for about 10 years, was admitted due to melena and progressive anemia. A gastroduodenoscopy revealed a cherry red and fern-like lesion with oozing on the posterior wall at junction of gastric body and fundus. Endoscopic hemoclipping therapy was performed. However, melena recurred four days later. Argon plasma coagulation and hemoclipping therapy were performed again. Since then, no recurrence of bleeding has been observed.

• Radiation Oncology Journal
• /
• v.32 no.2
• /
• pp.63-69
• /
• 2014

Purpose: To find the applicability of adjuvant radiotherapy for extrahepatic bile duct cancer (EBDC), we analyzed the pattern of failure and evaluate prognostic factors of locoregional failure after curative resection without adjuvant treatment. Materials and Methods: In 97 patients with resected EBDC, the location of tumor was classified as proximal (n = 26) and distal (n = 71), using the junction of the cystic duct and common hepatic duct as the dividing point. Locoregional failure sites were categorized as follows: the hepatoduodenal ligament and tumor bed, the celiac artery and superior mesenteric artery, and other sites. Results: The median follow-up time was 29 months for surviving patients. Three-year locoregional progression-free survival, progression-free survival, and overall survival rates were 50%, 42%, and 52%, respectively. Regarding initial failures, 79% and 81% were locoregional failures in proximal and distal EBDC patients, respectively. The most common site was the hepatoduodenal ligament and tumor bed. In the multivariate analysis, perineural invasion was associated with poor locoregional progression-free survival (p = 0.023) and progression-free survival (p = 0.012); and elevated postoperative CA19-9 (${\geq}37U/mL$) did with poor locoregional progression-free survival (p = 0.002), progression-free survival (p < 0.001) and overall survival (p < 0.001). Conclusion: Both proximal and distal EBDC showed remarkable proportion of locoregional failure. Perineural invasion and elevated postoperative CA19-9 were risk factors of locoregional failure. In these patients with high risk of locoregional failure, adjuvant radiotherapy could be considered to improve locoregional control.

• Transactions of Materials Processing
• /
• v.12 no.2
• /
• pp.134-140
• /
• 2003

Polymers such as polypropylene or polyethylene offer a unique feature of producing an integral hinge, which can flex over a million times without causing a failure. With such advantage manufacturing, time and cost required at the assembly stage can be eliminated by injecting the whole part as one piece. However, due to increased fluidity resistance at hinges during molding, several defects such as short shot or premature hinge failure can occur with the improper selection of gate locations. Therefore, it is necessary to optimize flow balancer in injection molding of part with hinges before actually producing molds. In this paper, resin flow patterns depending on several gate positions were investigated by numerical analyses of a simple strip part with a hinge. As a result, we found that the properly determined gate location leads to better resin flow and shorter hesitation time. Finally, injection molding tryouts using a mold that was designed one of the proposed gate systems were conducted using polypropylene that contained 20% talc. The experiment showed that hinges without defects could be produced by using the designed gate location.