• Earthquakes and Structures
• /
• v.4 no.2
• /
• pp.133-155
• /
• 2013

The earthquake responses are studied for the tall flexible structures such as TV towers when the vertical eccentricities between the discrete nodes and the corresponding centroids of investigated lumps are considered. In practical analyses, the tall flexible structures can be made into a spatial-discrete system of some certain length of beam elements with different lengths and cross-sectional areas. These elements are used to construct the investigated lumps in this paper. The different cross-sectional areas and the different lengths of two adjacent elements lead to the appearance of vertical eccentricity between the discrete node and the centroid of investigated lump within the same investigated lump. Firstly, the governing equations are established for a typical investigated lump. Secondly, the calculating formulae of the forces and moments acting on the investigated lump are derived and provided. Finally the new dynamic equilibrium equations with modified mass matrix and assemblage of stiffness matrix have been derived for the stick MDOF model based on beam theory when the existing vertical eccentricities are considered. Numerical results demonstrate that these vertical eccentricities should be considered in order to obtain the accurate earthquake responses for the tall flexible structures.

• Journal of Conservation Science
• /
• v.36 no.6
• /
• pp.456-474
• /
• 2020

This study investigated the initial behavior (flowability and setting properties) and shrinkage characteristics of lime mortar, based on the mixing ratio of hydrated lime (lump, powder) and commercial lime, which is primarily used for repairing and restoring cultural assets. The flowability showed that the optimum mixing water contents of the masonry lime mortar were 8-10% for the lump hydrated lime, 10-18% for the powdered hydrated lime, and 17-40% for the commercial hydrated lime. The results of the setting and shrinkage analysis showed that the average final setting time ratio compared to the standard of cultural asset repair was in the increasing order of commercial hydrated lime(0.4) < powder hydrated lime(5.6) < lump hydrated lime(5.7). Moreover, the average shrinkage ratio was ordered as lump hydrated lime(1.1) < powder hydrated lime(1.2) < commercial hydrated lime(3.0). The analysis of the physical and chemical characteristics of hydrated lime showed that the optimum mixing water content was reduced as the particle size of the lime increased, thus delaying the setting time and decreasing the length change rate (shrinkage). These results are expected to contribute to the prediction of the initial behavior and shrinkage characteristics of mortars using handmade and commercial lime during repair and restoration work on cultural, heritage buildings.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2004.05a
• /
• pp.113-117
• /
• 2004

We need the contingency cost in order to deal with the uncertainty to be accompanied inevitably at the construction and an every kind risk not to forecast in advance. And also the contingency colt needed for the change order and we need it for reduction of the delay and reduce the trouble between owner and constructor. This study, through checking and analyzing the risk factor, in the step of domestic construction, suggests optimal management reserve to specific business about the contract type and the scale. The main results of this research are summarized as follow. First, I investigated the recognition about the contingency cost, grasped the risk to be happened at the construction step and found out the frequency occurrence, through making up question to engineer are carrying out their job in the domestic construction. Second, I computed optimal contingency cost rate by the statistics investigation, and proposed an improvement plan and problem when compute a contingency cost.

• Journal of the Korean Society of Food Culture
• /
• v.4 no.2
• /
• pp.155-159
• /
• 1989

The introduction of six kinds of teas in Koryo dynasty and tea-making in domestic were investigated. The results were certified as follows. 1. Lump-tea was introduced and then also produced in domestic. 2. It is assumed that scented-tea was made from white-tea. 3. It is assumed that strong-tea and large tea were blue tea. 4. Leap-tea, green-tea were druncken at the end of Koryo dynasty.

• Journal of the Korean Ceramic Society
• /
• v.33 no.1
• /
• pp.92-100
• /
• 1996

Amorphous alumina(AA) the precursor of ${\gamma}$-alumina for catalyst support was made in the newly designed ball filled heating column. Some properties of AA as precursor were investigated. In observation of microstruc-ture and pore structure of AA and its derivatives scanning electronic microscope(SEM) and transmission electronic microscope(TEM) were used. It was found that the width of one particle in AA was 45~60$\AA$ and the average distance among the particles ranged 9~12 $\AA$ which suggested a micropore structure. When AA was reacted with water the shape of the surface was found to be altered and acicular bioehmite was formed inside AA which contributed inproved formability. Pore distribution was evaluated for the three samples of AA ground and granulated lump and La2O3 coated alumina. Acid sites were quantitatively determined by ammonia TPD method and the effect of impurity of Na on acid sites was discussed. Water adsorption capacity was evaluated in terms of a desiccant.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.414-419
• /
• 2006

The ballast or other objects may be located on the rail road by a lump of ice, repairing operation on the track, or the strong gust due to the high speed running of the train. When a train operated in this condition, it causes serious damages to the wheel, train, and structures near the track, or the secondary ballast flying. To remove these objects safely, a ballast blower is suggested which was attached under the train. Firstly, the numerical analyses are investigated to find out the basic flow characteristics of the ballast blower. Next, the performance of the ballast blower is verified by wind tunnel experiments. Through these studies, it is expected that the ballast blower can be applied practically.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.1
• /
• pp.45-53
• /
• 2016

The interaction between the hull of ship and free surface of water generates important loads during slamming motion. In the present study, the slamming load applied on the sectional surface of two-dimensional arbitrary bodies has been investigated under several falling velocities. This simulation has been done with the commercial CFD software ANSYS FLUENT^®. Through the conventional MARINTEK experiments for the benchmark of the simulation, we verified the impact pressure values between the experiments and simulation results. Two arbitrary ship bow section models, Panamax-like(with small convex bulb and flare) and Post panamax-like(with large convex bulb and flare) are also investigated. Simulation results show that a maximum impact pressure on the Post panama-like shape is higher than the Panamax-like shape. According to both a lump of water generated by arbitrary shape and various dead-rise angles of the shape, the pressure picks were enhanced in the simulation.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.2
• /
• pp.56-61
• /
• 2015

In this study, the wear performance of manganese phosphate coating on SM45C with addition agent of Tartaric acid and Citric acid were investigated. The Surface morphology of manganese phosphate coating was examined by Scanning Electron Microscope (SEM) and Energy Dispersive X-ray spectroscopy (EDS). It is found that Mn, P, Fe, O and C. The crystal structure and thee composition was analysis and determined by using XRD. The XRD results indicated that manganese phosphate coatings are mainly composed of $(Mn,Fe)_5H_2(PO_4)_44H_2O$ and consists of a lot of close packed lump crystalline. Based on the time dependence of morphology and the weight of manganese phosphate coating, it shows that the phosphating process mainly includes three stages: corrosion of the substrate, creation and growth of phosphate crystal nucleus and thickening of manganese phosphate coating. The wear tests were performed in a ball on disc apparatus as per ASTM G-99 Standard. It was showed that the initial wear was quite high followed by low sludge.

• Journal of Acupuncture Research
• /
• v.22 no.5
• /
• pp.49-55
• /
• 2005

Objectives : In order to ensure safe Herbal Acupuncture treatment, the quality of needle tip is much important. Therefore we investigated micromorphological characteristics of Herbal Acupuncture needle tip according to the number of injection. Methods : We have selected the 26 Gage syringes & 29 Gage syringes that using currently in Herbal Acupuncture treatment. And we evaluated the change of shape of Herbal Acupuncture needle tip after several times of injection by Inverted System Microscope(x 200). Results & Conclusion : We found at Herbal Acupuncture needle tips had several defects such as hooked, scuffed, lump and irregular, stubbed or malformed shape in spite of new syringes. And we found at Herbal Acupuncture needle tips had several defects that is harmful to body such as mild pain, possibility of damage of tissue after several times of injection. Therefore it is necessary to pay attention to use Herbal Acupuncture needle tips.

• KSBB Journal
• /
• v.18 no.2
• /
• pp.127-132
• /
• 2003

The effect of 4 kinds of alcohols was investigated on the production of bacterial cellulose (BC) by Gluconacetobacter hansenii PJK. The addition of alcohols and acetic acid to medium caused the pellets of bacterial cellulose to aggregate into a lump, which could be easily separated from the culture medium. The growth rate of cells and the production yield of BC increased in the medium containing ethanol. Other alcohols in the medium decreased cell growth and the cellulose production rate, because of their toxic effects. The addition of ethanol depressed the conversion of a $\textrm{Cel}^{+}$ cell to a $\textrm{Cel}^{-}$ mutant in shaking culture. Cells subcultured three in a medium containing ethanol produced BC without any loss of BC production yield.