• Journal of Electrical Engineering and Technology
• /
• v.11 no.3
• /
• pp.733-740
• /
• 2016

To achieve bipedal walking in real human environments, a bipedal robot should be capable of modifiable walking both on uneven terrain with different heights and on flat terrain. In this paper, a novel walking pattern generator based on a 3-D linear inverted pendulum model (LIPM) is proposed to achieve this objective. By adopting a zero moment point (ZMP) variation scheme in real time, it is possible to change the center-of-mass (COM) position and the velocity of the 3-D LIPM throughout the single support phase. Consequently, the proposed method offers the ability to generate a modifiable pattern for walking on uneven terrain without the necessity for any extra footsteps to adjust the COM motion. In addition, a control strategy for bipedal walking on uneven terrain with unknown height is developed. The torques and ground reaction force are measured through force-sensing resisters (FSRs) on each foot and the foot of the robot is modeled as three virtual spring-damper models for the disturbance compensation. The methods for generating the foot and vertical COM of 3-D LIPM trajectories are proposed to achieve modifiable bipedal walking on uneven terrain without any information regarding the height of the terrain. The effectiveness of the proposed method is confirmed through dynamic simulations.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.2
• /
• pp.145-152
• /
• 1999

This paper presents an optimal design method for fuzzy logic controllers using genetic algorithms. In general, the design of fuzzy logic controllers has difficulties in the acquisition of exper's knowledge and relies to a great extent on empirical and heuristic knowledge which, in many cases, cannot be objectively justified. So, the performance of the controller can be degraded in the case of plant parameter variations or unpredictable incident which the designer may have ignored, and parameters of the fuzzy logic controller obtained by expert's control action may not be global. To solve these problems, the proposed method using genetic algorithms in this paper, can tune the parameters of fuzzy logic controller including scaling factors and determine the appropriate number of fuzzy reles systematically and automatically. We provide the second drder dead time plant and inverted pendulum system to evaluate the feasibility and generality of our proposed method. Comparison shows that the proposed controller can producd higher accuracy and a smaller number of fuzzy rules than manually tuned fuzzy logic controller.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.21 no.4
• /
• pp.499-505
• /
• 2011

In this paper, we proposed an adaptive fuzzy sliding mode control for nonlinear systems without parameter projection method. By modifying the controller structure, the parameters of the estimated input gain function are guaranteed not being identically zero and it is shown that the control scheme will not cause any implementation problem even if the estimated value of input gain function is zero at any moment during on-line operations. Except for the input gain function which an approximate estimate for its lower bound is needed, the proposed control scheme does not assume a priori the exact values of the bounding parameters. Based on Lyapunov synthesis methods, the overall control system guarantees that the tracking error asymptotically converges to zero and that all signals involved in controller are uniformly bounded. This can be illustrated by the simulation results for an inverted pendulum system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.7
• /
• pp.572-580
• /
• 2013

IEEE 802.15.4e is a prospective standard for low latency control application in industries. This paper proposes a framework to evaluate the closed loop IEEE 802.15.4e based WNCS performance. The framework consists of two models: closed loop control system model and network model. The network model focuses on the PHY parameters of wireless link and takes the channel parameters into consideration. The PHY model combining with MAC model gives the control system model the probability of packet loss in a super-frame. In addition, redundancy mechanism is considered in IEEE 802.15.4e to reduce to data frame loss probability. The simulation is implemented in Matlab, PHY model takes the channel parameters from empirical results. Hence our evaluation gives insight into behavior of WNCS in different environments and it provides us a tool to design wireless network to achieve a good performance for control system.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.6 no.2
• /
• pp.3-12
• /
• 1996

Sliding mode controller(SMC) is a simple but powerful nonlinear controller, because it guarantees the stability and the robustness. However, it leads to the high frequency chattering of the control input. Although the phenomenon can be avoided by introducing a thin boundary layer to the sliding surface, the method results in a steady state: error proportional to the boundary layer thickness. In this paper, we proposed a new sliding mode controller with self-tuning the thickness of a boundary layer. It uses a fuzzy rule base for tuning the thickness of a boundary layer. That is, the thickness is increased to some degree to reject a discontinuous control input at the initial state and then it is decreased as the states approaches to the steady states for improving the tracking performance. In order to assure the control performance, we perf'ormed the computer simulation using an inverted pendulum system as a controlled plant.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.11
• /
• pp.912-918
• /
• 2016

This paper presents various strategies for humanoid vehicle driving and egress tasks. For driving, a tele-operating system that controls a robot based on a human operator's commands is built. In addition, an autonomous assistant module is developed for the operator. Normal position control can result in severe damage to robots when they egress from vehicles. To prevent this problem, another approach that mixes various joint control techniques is adopted in this study. Additionally, a footplate is newly designed and attached to the vehicle floor for the ground landing phase of the egress task. The attached plate enables the robot to step down onto the ground in a safe manner. For stable locomotion, a balance controller is designed for the humanoid. For the design of the controller, the robot is modeled using an inverted pendulum that consists of a spring and a damper. Then, a state feedback controller (with pole placement and a state observer) is built based on the simplified model. Many approaches that are presented in this paper were successfully applied to a full-sized humanoid, DRC-HUBO+, in the DARPA Robotics Challenge Finals, which were held in the United States in 2015.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.10
• /
• pp.51-57
• /
• 1999

In this paper, we deal with the problem of controlling an unknown nonlinear dynamical system, using wavelet network. Accurate control of the nonlinear systems depends critically on the accuracy and efficiency of the function approximator used to approximate the function. Thus, we use wavelet network which shows high capability of approximating the functions and includes the free-selection of basis functions for the control of the nonlinear system. We find the dilation and translation that are wavelet network parameters by analyzing the time-frequency characteristics of the controller's input to construct an initial adaptive wavelet network controller. Then, weights is adjusted by the adaptive law based on the Lyapunov stability theory. We apply this direct adaptive wavelet network controller to control the inverted pendulum system which is an nonlinear system.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.5
• /
• pp.593-597
• /
• 2004

This paper presents the new design method of fuzzy control system for nonlinear system. Many conventional design methods for fuzzy controller find the control gain for stabilizing fuzzy controller with some mathematical approaches. However, there exist some controllers which are hard to design with mathematical approach. In order to solve these problems, we propose the intelligent design method for fuzzy controller by using genetic algorithm with evolution strategy. The genetic algorithm with evolution strategy finds the control gain by changing the evolution region of chromosome. Finally, an application example of stabilizing a cart-pole typed inverted pendulum system will be given to show the stabilizability of the fuzzy controller.

• Journal of the Korea Computer Graphics Society
• /
• v.1 no.2
• /
• pp.201-212
• /
• 1995

This paper presents a new method of dynamics-based synthesis of bipedal, especially human, walking. The motion of the body at a time point is determined by ground reaction force and torque under the support foot and joint torques of the body at that time point. Motion synthesis involves specifying conditions that constrain ground reaction force and torque, and joint torques so that a given desired motion may be achieved. There are conditions on a desired motion which end-users can think of easily, e.g. the goal position and orientation of the swing foot for a single step and the time period of a single step. In this paper, we specify constraints on the motion of the support foot, which end-users would find difficult to specify. They are constraints which enforce non-sliding, non-falling, and non-spinning the support foot. They are specified in terms of joint torques and ground reaction force and torque. To satisfy them, both joint torques and ground reaction force and torque should be determined appropriately. The constraints on the support foot themselves do not give any good clues as to how to determine ground reaction force and torque. For that purpose, we specify desired trajectories of the application point of vertical ground reaction force (ground pressure) and the application point of horizontal ground reaction (friction) force. The application points of vertical pressure and friction force are good control variables, because they are indicators to kinds of walking motions to synthesize. The synthesis of a bipedal walking motion, then, consists of finding a trajectory of joint torques to achieve a given desired motion, so that the constraints are satisfied under the condition of the prescribed center of pressure and center of friction. Our approach is distinguished from many other approaches, e.g. the inverted-pendulum approach, in that it captures and formulates dynamics of the support foot and reasonable constraints on it.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.7 no.4
• /
• pp.65-73
• /
• 1997

This paper proposes a new method of the structure pruning of dynamic recurrent neural networks (DRNN) using evolutionary computations. In general, evolutionary computations are population-based search methods, therefore it is very useful when several different properties of neural networks need to be optimized. In order to prune the structure of the DRNN in this paper, we used the evolutionary programming that searches the structure and weight of the DRNN and evolution strategies which train the weight of neuron and pruned the net structure. An addition or elimination of the hidden-layer's node of the DRNN is decided by mutation probability. Its strategy is as follows, the node which has mhnimum sum of input weights is eliminated and a node is added by predesignated probability function. In this case, the weight is connected to the other nodes according to the probability in all cases which can in- 11:ract to the other nodes. The proposed pruning scheme is exemplified on the stabilization and position control of the inverted-pendulum system and visual servoing of a robot manipulator and the effc: ctiveness of the proposed method is demonstrated by numerical simulations.