• Journal of Biosystems Engineering
• /
• 제28권4호
• /
• pp.285-294
• /
• 2003

This study was carried out to propose a new-concept internal combustion engine which has great potential advantages to the conventional engines. Proposed new-concept engine is a kind of rotary engine. A rotor is rotating concentrically in a cylinder which is divided into two partitioning valves, and it makes four compartments in the cylinder. The volumes of each of four compartments are changing continuously with the rotor movement and performs the functions of intake, compression. expansion and exhaust simultaneously. Expected thermal efficiency for the real cycle is 26 percent at conditions of 1,000 rpm and compression ratio of 8.0, which is 3 to 4 percent higher than that of the conventional engines such as the piston engine, gas turbine and Wankel rotary engine. A simulation procedure proved that the new concept engine is functional, and has many potential advantages compared to the existing conventional engines.

• International Journal of Automotive Technology
• /
• 제7권3호
• /
• pp.289-294
• /
• 2006

Better fundamental understanding of the interactions between the in-cylinder flows and combustion process is an important requirement for further improvement in the fuel economy and emissions of internal combustion(IC) engines. Flow near a spark plug at the time of ignition plays an important role for early flame kernel development(EFKD). Velocity data measurements in this study were made with a two-component laser Doppler velocimetry(LDV) near a spark plug in a single cylinder optical spark ignition(SI) engine with a heart-shaped combustion chamber. LDV velocity data were collected on an individual cycle basis under wide-open motored conditions with an engine speed of 1,000rpm. This study examines and compares the flow fields as interpreted through ensemble, cyclic and discrete wavelet transformation(DWT) analysis. The energy distributions in the non-stationary engine flows are also investigated over crank angle phase and frequency through continuous wavelet transformation(CWT) for a position near a spark plug. Wavelet analysis is appropriate for analyzing the flow fields in engines because it gives information about the transient events in a time and frequency plane. The results of CWT analysis are provided and compared with the mean flows of DWT first decomposition level for all cycles at a position. Low frequency high energy found with CWT corresponds well with the peak locations of the mean velocity. The high frequency flows caused by the intake jet gradually decay as the piston approaches the bottom dead center(BDC).

• 한국자동차공학회논문집
• /
• 제20권2호
• /
• pp.110-115
• /
• 2012

This study describes the characteristics of combustion and exhaust emission in the special engine applying a fuel reactivity controlled compression ignition (RCCI) concept with two different energizing type (solenoid and piezoelectric) injectors for diesel injection. A diesel-gasoline mixed dual-fuel reactivity controlled compression ignition concept is demonstrated as a promising method to achieve high thermal efficiency and low emission in internal combustion engines for transportation vehicles. For investigating the combustion characteristics of RCCI, engine experiments were performed in a light-duty diesel engine over a range of injection timing and mixing rate of gasoline in mass. It was investigated that by increasing the nozzle hole diameter, increasing the combustion pressure and the net indicated mean effective pressure. $NO_x$ and soot can be reduced by advancing start of injection in 84 mixing rate of gasoline in mass. The resulting operation showed that light duty engine could achieve 48 percent net indicated efficiency and 191[g/kW-hr] net indicated specific fuel consumption with lower levels of nitrogen oxides and soot.

• 한국자동차공학회논문집
• /
• 제14권3호
• /
• pp.178-185
• /
• 2006

This paper investigates the steady-state combustion characteristics of the Homogeneous charge compression ignition(HCCI) engine with variable valve timing(VVT) and dimethyl ether(DME) direct injection, to find out its benefits in exhaust gas emissions. HCCI combustion is an attractive way to lower carbon dioxide($CO_2$), nitrogen oxides(NOx) emission and to allow higher fuel conversion efficiency. However, HCCI engine has inherent problem of narrow operating range at high load due to high in-cylinder peak pressure and consequent noise. To overcome this problem, the control of combustion start and heat release rate is required. It is difficult to control the start of combustion because HCCI combustion phase is closely linked to chemical reaction during a compression stroke. The combination of VVT and DME direct injection was chosen as the most promising strategy to control the HCCI combustion phase in this study. Regular gasoline was injected at intake port as main fuel, while small amount of DME was also injected directly into the cylinder as an ignition promoter for the control of ignition timing. Different intake valve timings were tested for combustion phase control. Regular gasoline was tested for HCCI operation and emission characteristics with various engine conditions. With HCCI operation, ignition delay and rapid burning angle were successfully controlled by the amount of internal EGR that was determined with VVT. For best IMEP and low HC emission, DME should be injected during early compression stroke. IMEP was mainly affected by the DME injection timing, and quantities of fuel DME and gasoline. HC emission was mainly affected by both the amount of gasoline and the DME injection timing. NOx emission was lower than conventional SI engine at gasoline lean region. However, NOx emission was similar to that in the conventional SI engine at gasoline rich region. CO emission was affected by the amount of gasoline and DME.

• 에너지공학
• /
• 제25권4호
• /
• pp.170-175
• /
• 2016

현재 자동차의 주요 동력원은 내연기관이 가장 많은 비중을 차지하고 있다. 내연기관 자동차로 인한 환경문제를 해결하기 위한 친환경 자동차로는 하이브리드 자동차, 전기 자동차 및 공기 엔진 자동차 등을 들 수 있다. 배터리를 이용하는 하이브리드 차나 순수 전기차 등도 아직은 크지 않으나 점차 많은 비중을 차지하여 나가고 있다. 전기모터를 사용하는 전기차에 비해 압축공기를 이용하는 공기 엔진 자동차는 아직은 연구개발이 거의 이루어지지 않은 상태이다. 본 논문에서는 스크롤 팽창기를 적용하는 새로운 압축공기 엔진을 소개하고, 이 엔진을 장착한 자동차의 주행거리 가능 거리를 이론적으로 산출하였다.

• 한국자동차공학회논문집
• /
• 제8권1호
• /
• pp.23-31
• /
• 2000

Knock and misfire, kinds of abnormal combustion, are highly undesirable effect on the internal combustion engine. So, it is important to detect these avnormal combuition and control the ignition timing etc. to avoid these mal-effect factors in real engine system. In this study, the system which detects the knock and the misfire using by spark plug is presented. This system is based on the effect of modulation breakdown voltage(BDV) between the spark gaps. The voltage drop between spark plug electrodes, when an electrical breakdown is initiated, depends on the temperature and pressure in combustion chamber. So, we can detect knock and misfire that produce changes in gas temperature and pressure (consequently, its density) using by BDV signal change which carries information about the character of combustion.

• 한국분무공학회지
• /
• 제10권2호
• /
• pp.41-47
• /
• 2005

Exhaust gas emissions from internal combustion engines are one of the major sources of air pollution. And. it is extremely difficult to increase gasoline engine efficiency and to reduce NOx and PM(particulate matter) simultaneously in diesel combustion. This paper offers some basic concepts to overcome the above problems. To solve the problems, a recommended technique is CAI(controlled auto-ignition) combustion. In this paper. internal EGR(exhaust gas recirculation) effect is suggested to realize CAI combustion. An experimental study was carried out to achieve CAI combustion using homogeneous premixed gas mixture in the constant volume combustion chamber(CVCC). A flame trap was used to simulate internal EGR effect and to increase flame propagation speed in the CVCC. Flame propagation photos and pressure signals were acquired to verify internal EGR effect. Flame trap creates high speed burned gas jet. It achieves higher flame propagation speed due to the effect of geometry and burned gas jet.

• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.100-109
• /
• 1997

Parameters in the internal combustion engines are variable depending on the operating points. Therefore, it is necessary to compensate for the uncertainties. Form this point of view, this paper gives a controller design method and a robust stability condition by LMI approach for engine torque control which satisfies the gives H$\infty$ control performance in the presence of physical parameter perturbations. To the end, the robustness of the system in the presence of perturbation is guaranteed in the all engine operating regions. Its effectiveness is demonstrated by simulation.

• 한국자동차공학회논문집
• /
• 제17권4호
• /
• pp.63-71
• /
• 2009

The elastic effects of the valve train components are analyzed by using the finite element models of the rocker arm and valve. The whole equations of motion of the valvetrain of an internal combustion engine formulated by finite element techniques are solved by imposing the contact conditions with the augmented Lagrange multiplier method. The velocity and acceleration constraints as well as the displacement constraints are imposed on the contact points. The numerical simulations show that, even if the magnitude of the elastic deformation of the components is very small, it may have large effects on the valvetrain dynamics of a high-speed engine.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.1037-1042
• /
• 1990

The air-fuel ratio of an internal combustion engine must be controlled with accuracy for the improvements of exhaust emission and fuel consumption. Therefore, it is necessary to measure the exact instantaneous amounts of fuel and suction air, so we carried out the experiments for measuring the air flow velocity in a suction pipe of an internal combustion engine using three types of instantaneous air flowmeter. The results obtained can be summarized as follows: (1) The laminar-flow type flowmeter is able to measure both the average and the instantaneous flow rate, but it is necessary to rectify the pulsating air flow in the suction pipe. (2) The a spark-discharge type flow velocity meter is able to measure the instantaneous air velocity, but it is necessary to choose the suitable electrode form and the spark character. (3) The tandem-type hot-wire flow velocity meter indicates the instantaneous flow velocity and its flow direction.