• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.1
• /
• pp.1-8
• /
• 2021

In this paper, the cabinet shielding effectiveness (SE) including digital modules for nuclear power plants is analyzed depending on the internal structure and electromagnetic (EM) wave incidence angle. To analyze the SE, the cabinet and modules are modeled using the FEKO EM simulation tool. The SE is then obtained by comparing the electric field with and without the cabinet. In addition, the cabinet SE is observed by changing various conditions such as the spacing of each digital module, incidence angle, and the polarization of the EM wave at the 2.4 G[Hz frequency. To verify the results, the dipole antenna for SE measurements is fabricated, and the SE is measured in a semi-anechoic chamber. The result demonstrates that the SE by the cabinet structure can be expected to be higher when the polarization of the incident EM wave is horizontal to the ground and the distance between the digital modules is wide.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.577-580
• /
• 2004

To overcome with large size noise source distribution network design difficulty in interferometric radiometer system, especially for sub-Y-type array, a new on-board calibration technique using noise re-radiation is proposed in this paper. The suggested calibration technique is using noise re-radiation effect of center antenna after noise source injection from matched load. This approach is especially proper to sub-Y-type array interferometric synthetic aperture radiometer in mm-wave frequency band. Compared with noise injection network of a conventional synthetic aperture radiometer, the system mass, volume, and hardware complexity is reduced and cost-effective. Only one internal noise source, matched load, is used for injection using noise re-radiation technique a small set of sub-Y receiver channels is calibrated. Detailed calibration scenario is discussed and simulation results about noise re­radiation effect are presented.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.5
• /
• pp.560-566
• /
• 2004

In this paper, the electrical and emission properties of electrodeless fluorescent lamp were discussed using the inductively coupled plasma (ICP) with the variation of argon gas pressure and RF power. The RF output was applied to the antenna in the range of 5∼50 W at 13.56 MHz. The internal plasma voltage of the chamber and the probe current were measured while varying the supply voltage to the Langmuir probe in the range of －100V∼＋100V. When the pressure of argon gas was increased, electric current was decreased. There was a significant electric current increase from 10 to 30 W. Also, when the RF power was increased, electron density was increased. Also, the emission spectrum, Ar- I lins, luminance were investigated. At this time, the input parameter for ICP RF plasma, Ar gas pressure and RF power were applied in the range of 10∼60 mTorr, 10∼300 W, respectively. This implies that this method can be used to find an optimal RF power for efficient light illumination in an electrodeless fluorescent lamp.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.6
• /
• pp.1031-1040
• /
• 2023

Propagation characteristics in line-of-sight(LOS) paths in 3, 6, 10, and 17 GHz frequency bands were measured and analyzed in two different indoor corridors: second floors of Buildings D2 and E2. The measurement was designed to measure when the receiving antenna moved at 0.5 m intervals from 3 m to 30 m, while the transmission antenna was fixed. The analysis of the two indoor corridors was compared by applying basic transmission loss, root mean square (RMS) delay spread, and K-factor. For basic transmission loss, the loss coefficient of the floating intercept path loss model was higher in the indoor corridor of Building E2 than in that of Building D2. Similarly, the RMS delay spread in the time domain was greater in the indoor corridor of Building E2. However, the indoor corridor of Building D2 exhibited higher K-factor in the 3, 6, and 17 GHz bands with lower wave propagation in the 10 GHz band. Despite the 2 indoor corridors being identical, the propagation characteristics varied due to different internal structures and materials. The results provide measurement data for ITU-R Recommendations regarding various indoor environments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.11B
• /
• pp.997-1004
• /
• 2006

There is a growing demand to access the broadband internet while on the very fast move. In order to meet these users needs, much research has been made for providing the broadband internet and HDTV services via satellite broadband internet systems even at top train speeds above 200km/h. In this paper, economic analyses on the satellite broadband internet services for KTX are to be reviewed. Broadband internet to trains in Europe are investigated, and Boeing cases for planes are also examined. In the first step, system configuration which is composed of a hub, terminals, satellite, and gap fillers for the tunnel areas has been proposed. A terminal includes a ultra-fast high gain antenna installed on the roof of the train, and APs inside the coaches. Secondly, cost estimation on the capital expenditures as well as operating expenditures has been performed in the proposed configuration. From the european and Boeing cases, demand and tariff are postulated, consequently, service revenues are derived on the scenario basis. Thirdly, estimated costs and derived revenues make up net present value and internal rate of return in each scenario. Finally, conclusions and contribution of this study are presented.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.3
• /
• pp.299-309
• /
• 2013

A comprehensive SAR(Synthetic Aperture Radar) simulation is considered to be a complicated task since a full knowledge of the signal propagation characteristics, antenna pattern, system internal errors and interference noises should be taken into account. In high resolution target application modes, the time varying nature of target RCS(Radar Cross Section) strongly affects the generated SAR images. In this paper, in-depth SAR simulations are performed and analyzed incorporating the STK tools and MATLAB software. STK provides realistic orbit parameters while its radar module helps to extract accurate radiometric parameters of ground targets. SAR raw data corresponding to a given target is generated and processed using MATLAB simulator. The performance is measured by PSLR(Peak Sidelobe Ratio) and ISLR(Integrated Sidelobe Ratio) for a point target, which can be used as reference parameters for accurate radiometric calibration. Finally, high resolution target simulations are performed by adopting time varying target RCS characteristics.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.8
• /
• pp.392-398
• /
• 2006

The properties of tunable dielectric materials on RF frequency band are important high tunability and low loss for RF variable devices, variable capacitor, phased array antenna and other components application. Various composite of BST(barium strontium titanate) ratio combined with other non-electrical active oxide ceramics have been formulated for such uses. We present the tunable properties and Curie temperature on BST thick films. The grain growth of the weight ratio of $BaTiO_3$ increased. This can be explained by the substitute $Sr^{2+}$ ion for $Ba^{2+}$ ion in the $BaTiO_3$ system. The Curie temperature was shifted to lower temperature with increasing $SrTiO_3$in the $BaTiO_3-SrTiO_3$ system, because of decreasing the lattice constant. Also, the dielectric constant, tunability and K-factor of $(Ba_xSr_{1-x})TiO_3$ at over the Curie temperature decreased, at over the $60^{\circ}C$ fixation, maximum dielectric constant at Curie temperature and hence sharper phase transformation occurred at Curie temperature. The result were interpreted as a process of internal stress relaxation resulting form the increase of $90^{\circ}$ domains induced the BST. As a result, It is concluded that over the Curie temperature, frequency response and DC field effect for the tunable properties of BST thick film are suppressed by the transition broadening. For the application of tunable devices, that the curie temperature was investigated to be increased.

• Journal of Microbiology and Biotechnology
• /
• v.15 no.5
• /
• pp.1094-1099
• /
• 2005

Photosynthetic dinoflagellates contain a water-soluble, light-harvesting antenna called the peridinin-chlorophyll-protein (PCP) complex, which has an apoprotein with no sequence similarity to other known proteins. There are two forms of PCP apoproteins; the 15-kDa short form and the 32- to 35­kDa long form. The present study describes the PCP protein and its cDNA from Alexandrium tamarense. A cDNA library was constructed from mRNA isolated from A. tamarense. The complete PCP cDNA was generated by reverse-transcription coupled to polymerase chain reaction (RT-PCR), together with rapid-amplification of cDNA ends (RACE). The A. tamarense PCP cDNA encoded a 55-amino acid signal peptide and a 313-amino acid mature protein with a calculated mass of 32 kDa, which corresponded to that of the long form of PCP. Phylogenetic analysis indicated that the sequence of A. tamarense PCP did not cluster with the short-form PCPs, to which it was only about $55\%$ identical, but which were $79-83\%$ identical to other long-form PCPs. The deduced amino acid sequence of A. tamarense PCP contains an internal duplication, which suggests the possibility that long-form PCPs arose by gene duplication or by the fusion of genes encoding the short form. The abundance of PCP mRNA changed substantially in response to different light conditions, indicating the possible existence of a photo-acclimation response in A. tamarense.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.2
• /
• pp.180-185
• /
• 2011

The TPMS(Tire Pressure Monitoring System) is an electronic system designed to display the air pressure inside the pneumatic tires and report real-time tire-pressure information to the driver of the vehicle, either via a gange, a pictogram display, or a simple low-pressure warning light. Although the data measured by TPMS sensor is transmitted to internal signal processer in a vehicle through wireless communication, the receiver may suffers from various interferences such as amateur radio station, RFID(Radio-Frequency IDentification) for controlling container, RKE(Remote Keyless Entry) signal, and so on. In this paper, we consider beamforming technology to suppress various high-power interference signals for the TPMS wireless communications. Also, we propose the proper data structure and antenna arrangement for the beamformer inside the vehicle. The performance for the interference suppression is illustrated by computer simulation example.

• Journal of the Korean Geophysical Society
• /
• v.9 no.1
• /
• pp.1-6
• /
• 2006

To remove ringing and increase vertical resolution of GRP data, signature deconvolution was applied to GPR data obtained using a 100 MHz antenna in the Soyang Lake. The signature was extracted through stacking reflection signals from the lake bottom. Results of this deterministic deconvolution was compared with those from the conventional Wienner method. Due to increased vertical resolution, both deconvolution methods are able to resolve three or more layers in an apparent single layer on the input data. However, identification of reflection boundaries from ringing is not easy due to poor definition in the output data of the Wienner filter. On the contrary, the signature deconvolution greatly enhances both vertical resolution and definition of reflection boundaries, showing detailed internal stratigraphic features of the three sedimentary layers. Since extraction of signature at various depths is possible, this deconvolution method can be appled effectively to unstationary GPR data.