• Journal of Welding and Joining
• /
• v.29 no.2
• /
• pp.72-79
• /
• 2011

The scope of this investigation is to evaluate the effect of joining parameters on the microstructural features and mechanical properties of dissimilar aluminum alloys, 1mm-thickness fixing AA6K31 at the top position and fixing AA5J32 at the bottom position. The friction stir lap welds were studied under various welding conditions, rotation speed of 1000, 1250, 1500rpm and welding speed of 100, 300, 500, 700mm/min, respectively. Mechanical test has been investigated in terms of tensile shear test and hardness test. The results showed that three type nugget shapes such as onion ring, zigzag type, hooking with the void, have been observed with revolutionary pitch. All welding conditions fractured at the HAZ of top plate, A6K31 and also the strength compare with base metal of lap joints were low efficiency, 52~63%. The thickness of fractured position was decreased with the lower heat input conditions. The relationships were excellent due to linear between the effective thickness of fractured position and peak load. The fractured position was the interface between joint area and not joint area. Also the strength efficiency compared with base metal was lower than decreasing rate of thickness because the hardness was decreased at fractured position due to softened material.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1135-1142
• /
• 2015

Multilayered ZnO-$SnO_2$ heterostructure thin films consisting of ZnO and $SnO_2$ layers are produced by alternating the pulsed laser ablation of ZnO and $SnO_2$ targets, and their structural and field-effect electronic transport properties are investigated as a function of the thickness of the ZnO and $SnO_2$ layers. The performance parameters of amorphous multilayered ZnO-$SnO_2$ heterostructure thin-film transistors (TFTs) are highly dependent on the thickness of the ZnO and $SnO_2$ layers. A highest electron mobility of $43cm^2/V{\cdot}s$, a low subthreshold swing of a 0.22 V/dec, a threshold voltage of 1 V, and a high drain current on-to-off ratio of $10^{10}$ are obtained for the amorphous multilayered ZnO(1.5nm)-$SnO_2$(1.5 nm) heterostructure TFTs, which is adequate for the operation of next-generation microelectronic devices. These results are presumed to be due to the unique electronic structure of amorphous multilayered ZnO-$SnO_2$ heterostructure film consisting of ZnO, $SnO_2$, and ZnO-$SnO_2$ interface layers.

• Spatial Information Research
• /
• v.5 no.2
• /
• pp.185-194
• /
• 1997

Spatial decision support systems(SDffi), a new class of decision support system(DSS), result from the melding together of GIS and DSS, Planning support systems(PS5) add more advanced spatial analysis functions than GIS and intertemporal functions to the functions of SDSS. This paper reports the development of a planning support system providing a framework that facilitates urban planners and civil engineers in conducting coherent deliberations about the generation of satisficing sewers. 1he planning support system for the generation of satisficing sewers(PS5/GSS) was designed from the understanding that land use and development drive the demand for storm and sanitary sewers. Through four stages of supply, demand, alternative generation, and evaluation, PSS/GSS integrates basic planning, preliminary design, and engineering design of sewer. GIS and graphic user interface are excellent toolboxes for designing sewer networks, estimating the quantity of wastewater, and showing generated alternative sewers. A sewer model using simulation tedmique can generate an initial sewer. Users can define alternative sewers by the direct manipulation of sewer networks or by the manipulation of parameters in the sewer model. The sewer model evaluates the performance of the user defined alternatives.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.917-920
• /
• 2008

ECC is a special kind of high performance cementititous composite which exhibits typically more than 2% tensile strain capacity by bridging microcracks at a crack section. Therefore, micromechanics should be adopted to obtain multiple cracking and strain hardening behavior. This paper propose a linear elastic analysis method to simulate the multiple cracking and strain hardening behavior of ECC. In an analysis, the stress-crack opening relation modified considering the orientation of fibers and the number of effective fibers is adopted. Furthermore, to account for uncertainty of materials and interface between materials, the randomness is assigned to the tensile strength(${\sigma}_{fci}$), elastic modulus($E_{ci}$), peak bridging stress(${\sigma}_{Bi}$) and crack opening at peak bridging stress(${\delta}_{Bi}$), initial stress at a crack section due to chemical bonding, (${\sigma}_{0i}$), and crack spacing(${\alpha}_cX_d$). Test results shows the number of cracking and stiffness of cracked section are important parameters and strain hardening behavior and maximum strain capacity can be simulated using the proposed method.

• Journal of Korean Association for Spatial Structures
• /
• v.12 no.2
• /
• pp.45-53
• /
• 2012

This paper derives Isogeometric analysis and post-processing method of surface that are generated by NURBS basis function for accurate geometric modeling and structure analysis of free-form. By deforming these parameters that are consisted of control points, knots, polynomial, variable geometric models are derived. The basis function that is used to Isogeometric analysis is same to the basis function of NURBS that is used to generate geometric models. For performing isogeometric analysis, h-p-k refinement is performed without changing of original geometry. To visualize the results of isogeometric analysis that control points' displacements, post-processing method that is the interface method between IGES format and Rhinoceros is derived.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.27 no.2
• /
• pp.144-149
• /
• 2017

In this paper, we developed an intelligent and wideband RF-receiver module to represent a high dynamic range and good linearity characteristics up to 650MHz-2700MHz frequency band. and implemented an intelligent digital-RF- distorted signal measuring system for the RF distortion (intermodulation) signals. Broadband RF-receive module was designed to represent the optimized linear parameters of the receiver to meet the low noise and wide dynamic range. The designed intelligent digital-distortion(intermodulation) signal measument system measured by applying the 1MHz IF of third intermodulation signal of DUT and Measured data was recorded by program on the PC monitor with GUI interface. By variable up to 650MHz-2700MHz measured data showed up to -127.8dBc to -138dBc of the distortion (intermodulation) signal. And developed intelligent digital- distortion signal measurement system can be used to measure intermodulation distortion signal of wireless system widely.

• The Transactions of the Korea Information Processing Society
• /
• v.1 no.4
• /
• pp.531-540
• /
• 1994

Spline curve scheme is the most valuable tool for the CAD of industrial products. Hence, the development of a new, effective curve scheme can have immediate impact on the current design industries. This paper develops and implements a new methodology for the implementation of the visually continuous class of splines which can produce a more flexible and diverse curve shapes. This class of splines has advantaged over existing splines in that it can accommodate wider range of shapes while maintaining the interpolators property of the ordinary cardinal splines. Most importantly, we avoid using the previous method of implementing G$^1$ curves, where users must specify scalar values for the control of curve shapes. We derive and implement an easy-to -use transformation between the user-specified graphical tangent vectors and the actual parameters for the resulting curve. Since the resulting curve shape reflects original tangential direction faithfully, CAD users can simply represent approximate curve shapes with proper tangents. Consequently, a simple user interface device such as a mouse can effectively produce a various spline curves using the proposed spline tool.

• Coupled systems mechanics
• /
• v.6 no.4
• /
• pp.439-464
• /
• 2017

The hydro-elastic system consisting of a pre-stretched highly elastic plate, compressible Newtonian viscous fluid, and the rigid wall is considered and it is assumed that on the plate a lineal-located time-harmonic force acts. It is required to investigate the dynamic behavior of this system and determine how the problem parameters and especially the pre-straining of the plate acts on this behavior. The elasticity relations of the plate are described through the harmonic potential and linearized (with respect to perturbations caused by external time-harmonic force) form of these relations is used in the present investigation. The plane-strain state in the plate is considered and the motion of that is described within the scope of the three-dimensional linearized equations of elastic waves in elastic bodies with initial stresses. The motion of the fluid is described by the linearized Navier-Stokes equations and it is considered the plane-parallel flow of this fluid. The Fourier transform with respect to the space coordinate is applied for a solution to the corresponding boundary-value problem. Numerical results on the frequency response of the interface normal stress and normal velocity and the influence of the initial stretching of the plate on this response are presented and discussed. In particular, it is established that the initial stretching of the plate can decrease significantly the absolute values of the aforementioned quantities.

• Journal of IKEEE
• /
• v.20 no.3
• /
• pp.260-264
• /
• 2016

The MAX77846, which is compatible with MAX77826, is a sub-power management IC (PMIC) for the latest Wearable Watch and 3G/4G smart phones. The MAX77846 contains N-MOSFET (N channel Metal-Oxide Semiconductor Field-Effect Transistor), a high-efficiency regulator, and comparator, etc to power up peripherals. The MAX77846 also provides power on/off control logic for complete flexibility and an $I^2C$ (Inter Integrated Circuit) serial interface to program individual regulator output voltages. In this paper, the simplified power macro-model based on MAX77846 is designed to verify the performance of the battery voltage in terms of current and time, and simulated by using of the LTspice. In addition, it is verified how much time can the charged battery capacity for Samsung Galaxy Gear 2 be used to operate a specified function after measuring the currents flowing to carry out the main functions in real time, which will be applicable to design parameters for the advanced power module

• Korean Journal of Crystallography
• /
• v.6 no.2
• /
• pp.141-157
• /
• 1995

Single crystals of TeO2 with large diameter were grown by Czochralski technique with auto-diameter control system. The ratio of crystal to crucible was 60-70%. The effect of critical pulling and rotation rate on the crystal quality was studied. Optimum growth parameters for high quality crystal pulling rate was less than 1.2 mm/hr. The solid-liquid interface was convex at the rotation rate of 10-23 rpm and concave at the rotation rate of more than 25 rpm, depending on the size of crystal and crucible. The platinum concentration in the melts is one of the main factors of the constitutional supercooling and thus the bubble entrapment in the growing crystal. Growth axis was confirmed to {110} direction during the whole growth procedure. Infrared spectrometric study and dislocation density measurment by chemical etching method on the grown crystal were performed. Finally, the reasons of cooperation of striations, inclusions, and optical inhomogeneities were discussed.