• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1251-1254
• /
• 2006

A novel a-Si TFT integrated gate driver circuit using multi-thread driving has been developed. The circuit consists of two independent shift registers alternating between the two mode, "wake" and "sleep". The degradation of the circuit is retarded since the bias stress is removed during the sleep mode. It has been successfully integrated in 14.1-in. XGA LCD Panel, showing enhanced stability.

• 센서학회지
• /
• 제16권6호
• /
• pp.475-483
• /
• 2007

This paper proposes a readout integrated circuit (ROIC) for $32{\times}32$ infrared focal plane array (IRFPA) detector, which consist of reference resistor, detector resistor, reset switch, integrated capacitor and operational amplifier. Proposed ROIC is designed using $0.35{\;}{\mu}m$ 2P-4M (double poly four metal) n-well CMOS process parameters. Low noise folded cascode operational amplifier which is a key element in the ROIC showed 12.8 MHz unity-gain bandwidth and open-gain 89 dB, phase margin $67^{\circ}$, SNR 82 dB. From proposed circuit, we gained output voltage variation ${\Delta}17{\};mV/^{\circ}C$ when the detector resistor varied according to the temperature.

• 한국위성정보통신학회논문지
• /
• 제1권1호
• /
• pp.54-58
• /
• 2006

동작주파수를 쉽게 조절할 수 있는 신호생성용 안테나 (Antenna-Integrated Oscillator) 설계방법을 소개한다. 제안하는 회로는 광대역에서 부성저항을 갖는 능동회로 (Negative-Resistance Circuit)와 패치안테나로 구분되며, 오실레이터의 동작주파수는 안테나의 공진 주파수로 결정된다. 이러한 디자인 방법은 안테나와 오실레이터의 동작주파수 불일치로 인한 출력파워의 감소 가능성을 줄일 수 있다. 또, 제안하는 설계방법에서 안테나의 Feed 지점과 Feed 라인의 길이를 조절하여 최적의 출력파워를 낼 수 있음을 Load-Pull 시뮬레이션으로 확인하였다. C-band, X-band 회로를 각각 제작, 측정하였고 이를 통하여 설계방법의 타당성을 증명하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.710-713
• /
• 2004

The design, simulation, modeling and measurement of a low temperature co-fired ceramic (LTCC) RF switch module for GSM applications is presented in this paper. RF switch module is constructed using a Rx/Tx switching circuit and integrated low pass filter. The low pass filter function was designed to operate in th GSM band. Insertion and return loss of the low pass filter were designed less than 0.3 dB and better than 12.7 dB at 900 MHz. The RF switch module contained 10 embedded passives and 3 surface mount components integrated on $4.6{\times}4.8{\times}1.2$ nm, 6-layer multi-layer integrated circuit. The insertion loss of switch module was measured at 900 MHz was 11 dB.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제4C권6호
• /
• pp.255-262
• /
• 2004

In this paper, a number of double-layered microwave integrated circuits (MIC) have been designed and analyzed based on a developed finite-difference time-domain (FDTD) solver. The solver was first validated through comparisons of the computed results with those previously published throughout the literature. Subsequently, various double-layered MIC printed on both isotropic and anisotropic substrates and superstrates, which are frequently encountered in printed circuit boards (PCB), have been designed and analyzed. It was found that in addition to protecting circuits, the added superstrate layer can increase freedoms of design and improve circuit performance, and that the FDTD is indeed a robust and versatile tool for multilayer circuit design.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 E
• /
• pp.1843-1845
• /
• 1998

Gyroscope is a very important core sensor as a rotation sensor in inertial space, in inertial guidance and navigation system on aeronautics. Plane, vessel and so on for civilian and millitary applications. Research and development of fiber optic gyroscope began in 1976 and focused on improving the gyroscope's sensitivity to rotation. bias performance and reducing noise. We have developed a Interferometric Fiber Optic' Gyroscope using a integrated-optic-circuit (IOC), which is operating with closed-loop electronic circuit. This paper describes the scheme of optical part and electronic part and also test results of this fiber optic gyroscope using a integrated-optic-circuit (IOC). The performance have been achieved as long-term bias drift of $1.73^{\circ}/h$.

• Journal of electromagnetic engineering and science
• /
• 제14권4호
• /
• pp.342-345
• /
• 2014

An active frequency doubler monolithic microwave integrated circuit (MMIC) for E-band transceiver applications is presented in this letter. This MMIC has been fabricated in a commercial $0.1-{\mu}m$ GaAs pseudomorphic high electron mobility transistor (pHEMT) process on a 2-mil thick substrate wafer. The fabricated MMIC chip has been measured to have a high output power performance of over 13 dBm with a high fundamental leakage suppression of more than 38 dBc in the frequency range of 71 to 86 GHz under an input signal condition of 10 dBm. A microstrip coupled line is used at the output circuit of the doubler section to implement impedance matching and simultaneously enhance the fundamental leakage suppression. The fabricated chip is has a size of $2.5mm{\times}1.2mm$.

• ETRI Journal
• /
• 제33권5호
• /
• pp.818-821
• /
• 2011

A D-band subharmonically-pumped resistive mixer has been designed, processed, and experimentally tested. The circuit is based on a $180^{\circ}$ power divider structure consisting of a Lange coupler followed by a ${\lambda}$/4 transmission line (at local oscillator (LO) frequency). This monolithic microwave integrated circuit (MMIC) has been realized in coplanar waveguide technology by using an InAlAs/InGaAs-based metamorphic high electron mobility transistor process with 100-nm gate length. The MMIC achieves a measured conversion loss between 12.5 dB and 16 dB in the radio frequency bandwidth from 120 GHz to 150 GHz with 4-dBm LO drive and an intermediate frequency of 100 MHz. The input 1-dB compression point and IIP3 were simulated to be 2 dBm and 13 dBm, respectively.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2005년도 추계 학술대회
• /
• pp.160-164
• /
• 2005

In this paper, MEMS inductor was integrated on a 5GHz VCO using BCB as low-k dielectric layer for MEMS inductor. The VCO core circuit is realized by IBM SiGe process. We varied the spiral inductor's suspension height and posit ion on circuit, and studied their circuit interference effect on VCO performance. The VCO with inductor placed on BCB with More height and the VCO with inductor that was not positioned above active area showed better characteristics.

• 대한전자공학회논문지
• /
• 제23권6호
• /
• pp.923-928
• /
• 1986

This paper describes the design and fabrication of a high performance digital tuning analog component integrated circuit that contains a television station detector and decoders(H and L types). When the comparator level sampling method is used, this integrated circuit can be used as a stable channel selector for an external circuit with very large signal variation. It has been fabricated using the SST bipolar standard process and its chip size is 2.2x2.1mm\ulcorner As a result, we have succeeded in fabricating the IC that satisfies the D.C characteristics, and the channel station detector and decoder function.