• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1505-1510
• /
• 2007

In this paper, the power simulation is used for the prediction of regenerative energy and examination of install location of regenerative inverter for DC railway system. The power simulation was composed to train performance simulation(TPS) and power flow simulation. We performed the power simulation for Seoul subway line 5 and 7, calculation of regenerative energy and examination of substations where regenerative inverter is installed.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.14 no.4
• /
• pp.1-9
• /
• 2015

Since logical ground and method to deduct location to install Integrated Standard Controller under development to combine physically and functionally multiple enclosures of controllers for various ITS equipments on streets into one enclosure, there are much difficulty to apply it to site. Particularly we need to establish standardized methodology to deduct optimal location to integrate individual controllers installed dispersedly on streets such as node part and line part. Accordingly this study has the purpose of suggesting more reasonable and efficient methodology to determine location for Integrated Standard Controller to be developed newly. For this, new solution has been searched by using centroid which is utilized to decide facility location in urban planning. As the result of analysis, central point among centroid, in which equal connection to each equipment is possible is proved to be the most reasonable and correct coordinate and zone is proposed as installation location through designating coordinate system. The methodology suggested by this study seems to have high degree of utilization in site according to expansion of integrated standard controller market.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.5
• /
• pp.1083-1094
• /
• 2012

Commercialized location estimation System with high accuracy is widely used for various services. However, if the systems aren't completely installed in an indoor, location estimation accuracy tend to be very poor. In this paper, indoor location estimation algorithm to improve the accuracy of object location, by correcting the location information obtained from a system that does not fully install, is proposed. In this paper, UWB-based Ubisense system that provides high position accuracy in an indoor environment was utilized. In conclusion, this paper was able to improve the positioning accuracy, by correcting that information about the location of the measured object in position estimation system.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.3
• /
• pp.11-19
• /
• 2014

This paper describes interference effect analysis of transverse member based on large-scale pullout test results of steel strip reinforcement with '${\sqcap}$' type transverse member. The maximum passive resistance has a difference according to the installed location of transverse member, and the total pullout resistance is increased, when transverse member was closed to the wall facing. The degree of interference confirmed that the install location of transverse member cannot reflect the pullout force differential, if S/B is equal. However, The interference factor based on maximum passive resistance reflected the differential of maximum passive resistance and install location of transverse member.

• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.443-445
• /
• 2000

This paper describes the assessment of proper location of lightning arrester in combined transmission line which is connected with overhead line and underground cable. The modeling for simulation is established using the actual system in ATP Draw and EMTP. Simulation is carried out to find out the best point to install the arrester in given the model system. And also voltage and current is analyzed on cable covering protection unit(CCPU). The simulation result demonstrated the best location of arrester in the given transmission line through the detailed analysis and its assessment.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.2
• /
• pp.148-155
• /
• 2005

This study was carried out to analyze the effect of direction of wind load and machinery house location on the stability of container crane loading/unloading a container on a vessel. The overturning moment of container crane under wind load at 50m/s velocity was estimated by analyzing reaction forces at each supporting point. And variations of reaction forces at each supporting point of a container crane were analyzed according to direction of wind load and machinery house location. The critical location of machinery house was also investigated to install a tie-down which has an anti-overturning function of container crane at the land side supporting point.

• Progress in Superconductivity and Cryogenics
• /
• v.11 no.4
• /
• pp.29-32
• /
• 2009

This paper proposes the bus-tie application scheme of 154 kV SFCL (superconducting fault current limiter) in Korean power system. The reduced amount of fault current by SFCL is different by where the SFCL is installed. Therefore the inflow ratio of fault current (IRFC) is suggested to consider the effect of an SFCL's location. The proposed scheme was applied to the Korean Power System of 2010, and fault currents were calculated and analyzed with this coefficient. Simulations show that the location with high IRFC is adequate to install SFCL but more consideration of other things is required to determine the location and capacity of SFCL.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.9
• /
• pp.9-17
• /
• 1999

This investigation is the result of the structural analysis by finite element method for optimal design of the cross beam with circular holes of the electric car-body. in order to install the air pipe and electric wire pipe that correspond signal between electric machines for the control system and to reduce the weight of the electric car-body, several circular areas from a cross beam should be taken off. What we want to perform is the optimal design of a cross beam with circular holes to posses equal stress in comparison with no hole cross beam. first, no hole cross beam as basic modal be chosen, executing the analysis, reviewing the distribution of stress and displacement at each location. several parameter should be adopted from the cross beam geometry like the location and shape of the hole to affect the maximum stress and displacement. So the analysis was executed by finite element analysis for finding optimal design parameter to the change of the location and shape of the circular hole. finally, the optimal design of the cross beam with circular holes was obtained and the maximum equivalent stress was compared with no hole cross beam at each location.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.47-48
• /
• 2022

The positioning technology that measures the position of a person or object is a key technology to deal with the location of the real coordinate system or converge the real and virtual worlds, such as digital twins, augmented reality, virtual reality, and autonomous driving. In estimating the location of a person or object at an indoor construction site, there are restrictions that it is impossible to receive location information from the outside, the communication infrastructure is insufficient, and it is difficult to install additional devices. Therefore, this study tested the direct sparse odometry algorithm, one of the visual Simultaneous Localization and Mapping (vSLAM) that estimate the current location and surrounding map using only image information, at an indoor construction site and analyzed its applicability as an indoor positioning technology. As a result, it was found that it is possible to properly estimate the surrounding map and the current location even in the indoor construction site, which has relatively few feature points. The results of this study can be used as reference data for researchers related to indoor positioning technology for construction sites in the future.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2577-2580
• /
• 2003

In this paper we present a teleoperation system of an internet-based mobile robot based on H.263 image compression algorithm. We control remotely the networked mobile robot with vision over the internet under unknown environments in the real time. The main feature of this system is that local operators need to download and install a client program and so they can command the robot in a remote location. Image information of remote location is compressed by H.263 video codec algorithm and then transmitted to a local operator. We constructed and tested a networked autonomous mobile robot in the real field. The experimental results show the usefulness of the robot under test.