• 한국전자파학회논문지
• /
• 제21권9호
• /
• pp.1056-1064
• /
• 2010

본 논문에서는 백 플레인의 개구를 관통하는 대칭 전송 선로 구조를 해석하기 위한 근사 해석법을 제안하고 있다. 제안된 방법은 백 플레인의 개구면 임피던스를 모멘트 법으로 계산하고, 이 값을 전송 선로에 병렬로 연결한 근사 등가 전송 선로를 해석하여 삽입 손실 특성을 계산하는 방법이다. 근사 해석법을 적용하여 계산한 결과, 정합이 되었을 때는 관통하는 전송 선로와 개구가 가까울수록 특정 주파수에서 삽입 손실이 증가하며, 부정합된 경우에는 특정 주파수에서 삽입 이득 현상이 나타나고 있다. 또한, 개구의 가로 길이가 세로 길이보다 전송 선로에 더 큰 영향을 미친다는 것도 확인하고 있다. 근사 해석법의 타당성을 검증하기 위해, 근사 해석법으로 계산된 삽입 손실 특성을 실험치 및 상용툴의 계산 결과와도 비교하였다.

• 한국통신학회논문지
• /
• 제24권12A호
• /
• pp.1939-1947
• /
• 1999

본 논문에서는 이진데이터의 고속전송을 위하여 기존의 선로 부호의문제점을 해결하는 새로운 형태의 선로부호 BIM(Bit Insertion and Manipulation) 선로부호를 제안하였다. 기존의 이진데이터 고속전송을 위한 mBnB 형태의 블록 부호는 전송 특성은 우수하나 구현이 어려운 단점이 있었으며, 또 다른 형태의 선로 부호인 비트 삽입 부호는 구현은 용이하나 전송 특성이 떨어지는 문제점이 있었다. 본 논문에서의 BIM 선로 부호는 이러한 문제를 극복하기 위하여 제안되었으며 비트 삽입 부호에 블록 부호의 특성을 적절히 결합함으로써 구현이 용이하면서도 우수한 전송 특성을 제공할 수 있었다. 본 논문에서 설계된 5B6B 형태의 BIM 부호는 $\pm$2 DSV, 0 RSD, 7 최대 런 길이와 같이 우수한 전송 성능뿐 아니라 1비트의 리던던시만을 필요로 하며 200 게이트 이하로 구현이 가능함으로써 구현의 용이성을 함께 보여 주었다.

• 대한전자공학회논문지SD
• /
• 제41권2호
• /
• pp.67-75
• /
• 2004

본 논문은 인덕턴스 성분을 포함한 단일 도선 및 트리 구조 RLC 연결선의 버퍼 삽입 방법을 제시한다. 이를 위해 먼저 CMOS 버퍼가 구동하는 단일 RLC 도선에 대한 시간 지연의 대수식을 제시한다. 이 수식은 현재의 서브마이크로미터 공정을 위한 n-th power law 기반에서 유도되었으며, 다양한 RLC 부하를 가지고 실험해 본 결과, 실제 SPICE 시뮬레이션 결과에 비해 최대 9％ 오차를 갖는 것으로 나타났다. 본 논문은 이 지연 시간 수식을 바탕으로 단일 도선 RLC 연결선을 여러 개로 나누는 버퍼 삽입에 관한 수식과 RLC 트리 연결선의 시간 지연을 최적화하기 위해 삽입될 버퍼의 사이즈를 결정하는 알고리듬을 제시한다. 제시된 버퍼 삽입 알고리듬은 0.25㎛ CMOS 공정의 트리 연결선에 적용하였으며, HSPICE 결과를 이용하여 정확도를 검증하였다.

• 대한전기학회논문지:전력기술부문A
• /
• 제52권12호
• /
• pp.675-683
• /
• 2003

This paper describes the correction strategy of an overcurrent relay applied in the linked line for interconnecting wind farm with utility power networks in order to improve the capability of a fault detection. The fault current measured in a relaying point might vary according to the fault conditions. Generally, the current of the line to line fault or the line to ground fault in the linked line is much higher than the set value of protective relay due to the large fault level. However, when the high impedance fault occurs in the linked line, we can't detect it by conventional set value because its fault level may be lower than the generating capacity of wind farm. And, the protective relay with conventional set value may generate a trip signal for the insertion of wind turbine generators due to the large transient characteristics. In order to solve above problems and improve protective relaying algorithms applied in the linked line, we propose a new correction strategy of the protective relay in the linked line. The presented method can detect the high impedance fault which can't be detected by conventional relay set value and may prevent the mis-operation of protective relay caused by the insertion of wind farm.

• 한국정밀공학회지
• /
• 제20권1호
• /
• pp.99-106
• /
• 2003

Uninterrupted power supply has become indispensable during the maintenance task of active electric power lines as a result of today's highly information-oriented society and increasing demand of electric utilities. The maintenance task has the risk of electric shock and the danger of falling from high place. Therefore it is necessary to realize an autonomous robot system. In order to realize these tasks autonomously, the there dimensional position of target object such as electric line and the stand of insulator must be recognized accurately and rapidly. The insertion task of an electric line into a sleeve is selected as the typical task of the maintenance of active electric power distribution lines in this paper. A modified hough transform is applied to the recognition of the center of electric line and optimal target position calculation method is newly derived in order to recognize the center 3 dimensional position of the electric line. By the proposed method, it is proved that the center position of the electric line can be recognized without respect to the noise of image and the shape of electric lines and the insertion task of an electric tine is realized.

• Genomics & Informatics
• /
• 제6권2호
• /
• pp.64-67
• /
• 2008

The Korean Rice Ds-tagging lines Database (KRDD) is designed to provide information about Ac/Ds insertion lines and activation tagging lines using japonica rice. This database has provided information on 18,158 Ds lines, which includes the ID, description, photo image, sequence information, and gene characteristics. The KRDD is visualized using a web-based graphical view, and anonymous users can query and browse the data using the search function. It has four major menus of web pages: (i) a Blast Search menu of a mutant line; Blast from rice Ds-tagging mutant lines; (ii) a primer design tool to identify genotypes of Ds insertion lines; (iii) a Phenotype menu for Ds lines, searching by identification name and phenotype characteristics; and (iv) a Management menu for Ds lines.

• Journal of Korean Biological Nursing Science
• /
• 제18권4호
• /
• pp.257-263
• /
• 2016

Background: This study purposed to examine how the incidence of the central line-associated bloodstream infection (CLABSI) in a operating room (OR) is affected by bundle application on central line insertion (CLI) practice. Methods: The study design was a pretest-posttest experimental trial. The subjects were 83 patients before the bundle application on CLI and 70 patients after. Results: The compliance(%) of bundle on CLI of among those who observed all of the five items increased from 7.2% before the intervention to 72.9% after. By items, compliance with the maximal barrier precaution was 100% for the use of a mask and cap before and after the intervention, but increased from 73.5% before the intervention to 88.6% after for the hand hygiene, from 73.5% to 88.6% for the use of a sterile gown, and from 9.6% to 75.7% for the use of a sterile large drape covering the whole body. CLABSI did not happen on CLI either before or after the application of the bundle intervention. Conclusion: Bundle application increased compliance with the use of a sterile gown and the use of a sterile large drape. However, its effect in the prevention of CLABSI was not clear probably due to the short period of intervention in a single hospital.

• Journal of electromagnetic engineering and science
• /
• 제6권2호
• /
• pp.110-116
• /
• 2006

A reflective array type surface acoustic wave(SAW) dispersive delay line(DDL) with high time-bandwidth at the V/UHF-band is designed and fabricated for compressive receiver applications. This type of the SAW DDL has the properties of the relative bandwidth of 20 %, the time delay of 49.89 usec, the insertion loss of 38.5 dB and the side lobe rejection of 39 dB. In comparison with a commercial SAW DDL, the insertion loss, amplitude ripple and side lobe rejection are improved by $1.5dB{\pm}0.6dB$ and 4 dB respectively. Using the fabricated SAW DDL, the prototype of the compressive receiver is developed. It is composed of RF converter, fast tunable LO, chirp LO, A/D converter, signal processing unit and control unit. This prototype system shows a fine frequency resolution of below 30 kHz with high scan rate.

• 대한산업공학회지
• /
• 제20권3호
• /
• pp.15-34
• /
• 1994

This paper considers the genetic algorithms(GAs) for the mixed model assembly line sequencing(MMALS) in which the objective is to minimize the overall line length. To apply the GAs to the MMALS, the representation, selection, genetic sequencing operators, and genetic parameters are studied. Especially, the existing sequencing binary operators such as partially map crossover(PMX), cycle crossover(CX), and order crossover (OX) are modified to be suitable for the MMALS, and a new sequencing binary operator called immediate successor relationship crossover (ISR) is introduced. These binary operators mentioned above and/or unary operators such as swap, insertion, inversion, displacement, and splice are compared to find operators which work well in the MMALS. Experimental results indicate that 1) among the binary operators ISR operator is the best, followed by the modified OX, and the modified PMX, with the modified CX being the worst, 2) among the unary operators inversion operator is the best, followed by displacement, swap, and insertion, with splice being the worst, and 3) in general, the unary operators perform better than the binary operators for the MMALS.

• 대한전기학회논문지
• /
• 제39권2호
• /
• pp.149-156
• /
• 1990

In DC electric railway systems, the feeding currrnt is not permitted to flow backward in almost all the substations and the pantograph voltages at the regenerating cars rise extremely by the voltage drop of the resistance of the feeder line. In order to prevent the overrise of the pantograph voltage in power regenerating cars, the squeezing circuits for the regenerative current are equipped and this leads to double losses, which are an extra worn-out of the brake-shoes and an ineffective use of regenerative power. In this study, the insertion of resistors in the feeder line system is proposed as a possible method for the effective utilization of the regenerative power in the electric railways. Also it is investigated how the output voltages of substations affect the effective use of regenertive capability. The investigation results show that the energy savings and the reduction of the worn-out of the brake-shoe can be achieved at the same time by the insertion of resistors in the feeder line system.