• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.3
• /
• pp.70-79
• /
• 1996

In off-line process optimization, process parameters are controlled such that the process is robust against changes in equipment conditions and incoming materials. The off-line methods, however, are not effective when the changes are so large that process parameters need to be adjusted. On-line control can respond to such large changes, but process uniformity has not been controlled on-line due to the difficulties in modeling. This paper is aimed at developing a new on-line control methodology where the uniformity is controlled effectively. The process variability is categorized based on the physical considerations, and the process parameters are classi- fied considering their effects on the categorized process variabilities. On-line control is performed with the properly selected process parameters so that robustness may not be degraded. The developed methodology is applied to the single wafer plasma etching processes, which resulted in both higher within-a-wafer uniformity and compens- ation of the incoming material non-uniformity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.10
• /
• pp.635-640
• /
• 2016

This paper dealt with the deterioration characteristics and an on-line diagnosis equipment for SPDs (surge protective devices). An accelerated aging test was carried out using a $8/20{\mu}s$ standard lightning impulse current to analyze the changes of electrical characteristics and to propose the diagnostic parameters and the criterion for deterioration of ZnO varistor which is the core component of SPDs. Based on the experimental results, an on-line diagnosis equipment for SPD was fabricated, which can measure the total leakage current, reference and clamping voltage. The leakage current measurement circuit was designed using a low-noise amplifier and a clamp type ZCT. A linear controller, the leakage current measurement part and a HVDC were used in the measurement of reference voltage. The measurement circuit of clamping voltage consisted of a surge generator and a coupling circuit. In a calibration process, measurement error of the prototype equipment was less than 3%.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.6
• /
• pp.279-285
• /
• 2006

Power line communication channels are very complicated and models for communication channels vary with the types of electrical equipment, devices and load fluctuations. So, modeling and analysis of power line channels for implementation of power line communication systems is a very important process. Power line channel modeling and simulation are performed based on power system transient simulation models and power system CAD tools to create precise and accurate models. In this paper, a channel modeling and simulation method is proposed for power line communication systems using PSCAD/EMTDC, in which a PN 63 sequence code generator is applied for impulse response of the power line channel in the simulation model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.529-530
• /
• 2007

The paper considers the relation between on-line monitoring and diagnostics on the one hand and high-voltage (HV) withstand and partial discharge (PD) on-site testing on the other. HV testing supplies the basic data (fingerprints) for diagnostics. In case of warnings by on-line diagnostic systems, off-line withstand and PD testing delivers the best possible information about defects and enables the classification of the risk. Because alternating voltage (AC) is the most important test voltage, the AC generation on site is considered. Frequency tuned resonant (ACRF) test systems are best adapted to on-site conditions. They can be simply combined with PD measuring equipment. The available ACRF test systems and their application to electric power equipment -from cable systems to power transformers - is described.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.6
• /
• pp.518-523
• /
• 2005

Strip off-center is one of the major problems in hot strip mill line. The key to good centering is having good equipment, modern control systems, excellent maintenance and an understanding of milling process. Therefore, this study aims to develop a system that is useful for quantitative analysis of strip off-center. In this study, the measuring method of strip off-center was thoroughly studied and the exclusive control board to line scan camera were designed. Also, the manipulated type housing for line scan camera was developed to adjust initial parameters for strip width and center line. In order to check the accuracy and usefulness of the developed system, FM stand in $\#2$ Hot Strip Factory in Pohang Steel Works was targeted.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.1
• /
• pp.48-59
• /
• 2018

This paper is mainly concerned with developing the formulae of predicting thermal deformation of steel plate due to multi-line heating. By investigating the results of line heating test and numerical analysis, reasonable heat flux model has been defined. Formulae of predicting the transverse shrinkage and the angular distortion as the dominant thermal deformation types in plate forming by line heating have been derived based on the results of line heating test and numerical analysis with varying plate thickness, heating speed and distance between torches. This paper illustrates how the derived formulae are used in investigating the effect of multi-line heating upon the thermal deformation and how they can be used in defining the limit distance with that there is no interacted effect between torches. This paper ends with describing the extension of the present study.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.1 no.2
• /
• pp.20-25
• /
• 2004

In this study, a position control characteristics of pneumatic cylinder with transmission line is analyzed. Dynamic characteristics of transmission line using compressible fluid is changed by the flowing stiles of the fluid the diameter and the length of the line. But, the effect of the change of dynamic characteristics of transmission line by the flowing states on the position control characteristics can be neglected because of the friction force of the pneumatic cylinder. So, We assume that the position control characteristics is affected by the diameter and length of the transmission line. The experimental results according to the change of parameter of the transmission line show that the relation between the parameter of the transmission line and the position control characteristics of pneumatic cylinder driving system with the transmission line.

• The Journal of Information Technology
• /
• v.8 no.3
• /
• pp.25-33
• /
• 2005

This paper describe a method for measuring line impedance as a function of frequency for an energized powerline in normal operation. A small sinusoidal signal of a powerline communication utility frequency 30khz$\sim$1Mhz band is continuously injected into the line, and a implemented impedance analyzer calculates the indoor powerline channel impedance from the measured magnitude and phase of resulting voltage and current. The impedance measurement is executed over a range of frequencies to produce a wideband impedance versus frequency characteristic. Implemented impedance analyzer can analysis powerline communication environments measuring line impedance due to load caused in indoor. And measured analysis information through the database can use to evaluate performance of modem and to decide test environment standard.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.2
• /
• pp.6-13
• /
• 2021

Cases and studies on the selection method of CTQ are relatively active, but there are few cases or studies on the selection method of CTP which is important in the device industry. In fact, many companies simply select and manage CTP from the point of contact based on their experience and intuition. The purpose of this study is to present an evaluation model and a mathematical decision model for rational and systematic CTP selection to improve the process quality of semiconductor equipment lines. In the evaluation model, AHP (Analytic Hierarchy Process) analysis technique was applied to show objective and quantitative figures, and Fuzzy decision-making model was used to solve the ambiguity and uncertainty in the decision-making process. Decision Value (DV) was presented. The subjects were 22 process factors managed in the Plating Process that the representative equipment line can do. As a result, the evaluation model proposed in this study can support more efficient and effective decision-making for process quality improvement by more objectively measuring the problem of subjective CTP selection in manufacturing sites.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.1163-1175
• /
• 2016

In recent years, microgrids have been the focus of considerable attention in distributed energy distribution. Microgrids contain a large number of power electronic devices that can potentially cause negative impedance instability. Harmonic impedance is an important tool to analyze stability and power quality of microgrids. Harmonic impedance can also be used in harmonic source localization. Precise measurement of microgrid impedance and analysis of system stability with impedances are essential to increase stability. In this study, we introduce a new square wave current injection method for impedance measurement and stability analysis. First, three stability criteria based on impedance parameters are presented. Then, we present a new impedance measurement method for microgrids based on square wave current injection. By injecting an unbalanced line-to-line current between two lines of the AC system, the method determines all impedance information in the traditional synchronous reference frame d-q model. Finally, the microgrid impedances of each part and the overall microgrid are calculated to verify the measurement results. In the experiments, a simulation model of a three-phase AC microgrid is developed using PSCAD, and the AC system harmonic impedance measuring device is developed.