• Journal of KSNVE
• /
• v.3 no.4
• /
• pp.325-330
• /
• 1993

The longitudinal vibration of the tape in the tape transport system influences the performance of the nagnetic tape-recording system. Generally it is controlled by a passive method with impedance roller which is easy to implement and cost-effective. Therefore the effect of the impedance roller in reducing the tape vibration was analyzed in this paper. The practical tape transport system was modelled mathematically as a mass-spring system. Both simulation and experimental study were carried out in order to show the vibration reduction effect of the impedance roller.

• ETRI Journal
• /
• v.23 no.4
• /
• pp.199-201
• /
• 2001

The phase noise reduction in a configuration of the HEMT oscillator with a dielectric resonator coupled by a quarter-wavelength impedance inverter is investigated. Two HEMT oscillators for a satellite payload system are manufactured in the same configuration except for the coupling configuration of the dielectric resonator (DR) in order to empirically demonstrate the phase noise reduction. Experimental result shows that a phase noise reduction by 14 dB can be enhanced by increasing the characteristic impedance of a coupling microstrip impedance inverter.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.423-426
• /
• 2007

In this paper, vibration reduction of resiliently mounted machinery and effect of the foundation impedance is studied. SBN (Structure-borne noise) reduction through the mount is analyzed by assuming that the system is modeled as a mass-spring system, while the impedance of the floor is included in the prediction. The comparison of the SBN difference through the mount between predictions and measurements show that the slopes are similar in the case of single-mount system, while the measurements differs significantly from the predictions in the case of the double-resilient system.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.2
• /
• pp.106-114
• /
• 2005

This article covers the theoretical ac-impedance models for the analysis of oxygen reduction on the porous cathode electrode f3r solid oxide fuel cell (SOFC). Firstly, ac-impedance models were explained on the basis of the mechanism of oxygen reduction, which were classified into the rate-determining steps; (i) adsorption of oxygen atom on the electrode surface, (ii) diffusion of adsorbed oxygen atom along the electrode surface towards the three-phase (electrode/electrolyte/gas) boundaries, (iii) surface diffusion of adsorbed oxygen atom m ixed with the adsorption reaction of oxygen atom on the electrode surface and (iv) diffusion of oxygen vacancy through the electrode coupled with the charge transfer reaction at the electrode/gas interface. In each section for ac-impedance model, the representative impedance plots and the interpretation of important parameters attributed to the oxygen reduction reaction were explained. Finally, we discussed in detail the applications of the proposed theoretical ac-impedance models to the real electrode of SOFC system.

• KIEE International Transactions on Power Engineering
• /
• v.4A no.4
• /
• pp.236-242
• /
• 2004

Previous research results indicated that the designed current reduction device could effectively reduce the sheath circulating current and that its RDP protection device could shield it against both fault and lightning strokes. In this paper, cable impedance is analyzed using wavelet analysis and distance relay algorithm following the installation of these devices so that the operation of distance relay can be estimated. The test results confirm that in these devices, the fault inception angle and SVL bonding types have no impact on the change of cable impedance. In other words, the conventional distance relay can be used without a new relay setting. Thus we can finally assert that the designed current reduction device and its protection device are effective and can be safely installed on the cable transmission system without disturbance.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.4
• /
• pp.300-307
• /
• 2003

This paper presents the multi-mode noise reduction of smart panels of which passive piezoelectric shunt damping is introduced. For the piezoelectric shunt damping, a passive shunt circuit composed of inductors and a load resistor is connected to the piezoelectric patch mounted on the panel structure. An electrical impedance model is introduced for the system based on the measured electrical impedance, and the criteria for maximum energy dissipation at the shunt circuit is used to find the optimal shunt parameters. For multi-mode shunt damping, the shunt circuit is modified by the introduction of a block circuit. Also the optimal location of the piezoelectric patch is studied by finite element analysis in order to cause the maximum admittance from the patch for each mode of the structure. An acoustic test is performed for the panels and a remarkable noise reduction is obtained in multiple modes of the panel structure.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.2E
• /
• pp.50-55
• /
• 2007

SBN (Structure-Borne Noise) reduction in resiliently mounted machineries are predicted by using mass-spring model and wave model. In mass-spring model, mount is modeled as a spring, while in wave model, mount is considered as an equivalent elastic rod for taking account into longitudinal wave propagation. The predictions for SBN reduction through mounts are compared to the measurements for four different pumps. It is found that the mass-spring model is valid only in low frequency range below few hundred Hz, while for high frequency ranges longitudinal wave propagation in the mount must be considered to explain the measurements. It is also shown that impedance of the floor slightly affects low frequency behaviour in mass-spring and wave model below 50 Hz - 80 Hz, so that in engineering practice the effect of floor impedance may be neglected in computing mount performance.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.124-127
• /
• 2006

In this paper, noise and vibration reduction of double-resiliently mounted pump-like machinery is studied. SBN(Structure-borne noise) reduction through upper and lower mount is analyzed by assuming that the system is modeled as a mass-spring system. In addition, the impedance of the floor is included in the prediction. The comparison of the SBN difference through upper mount show that the effect of impedance is negligible, while the measurement differs significantly from the prediction for high frequency range. It is found that the assumption of point mass-spring system leads to the disagreement between prediction and measurements.

• The Journal of Korea Robotics Society
• /
• v.14 no.4
• /
• pp.348-356
• /
• 2019

The backdrivable servovalve is a desirable component for force and interaction control of hydraulic actuation systems because it provides direct force generation mechanical impedance reduction by its own inherent backdrivability. However, high parametric uncertainty and friction effects inside the hydraulic actuation system significantly degrade its advantage. To solve this problem, this letter presents a disturbance-adaptive robust internal-loop compensator (DA-RIC) to generate ideal interactive control performance from the backdrivable-servovalve-based system. The proposed control combines a robust internal-loop compensator structure (RIC) with an explicit disturbance estimator designed for asymptotic disturbance tracking, such that the controlled system provide stable and ideal dynamic behavior for impedance control, while completely compensating the disturbance effects. With the aid of a backdrivable servovalve, we show that the proposed control structure can be implemented based on a simplified nominal model, and the controller enables implementation without accurate knowledge of the target system parameters and disturbances. The performance and properties of the proposed controller are verified by simulation and experiments.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.127-132
• /
• 2001

In this paper, transmitted sound reduction performance of smart panels is studied according to different piezoelectric materials with piezoelectric shunt damping. Peizo-damping is implemented by using a newly proposed tuning method. This method is based on electrical impedance model and maximizing the dissipated energy at the shunt circuit. By measuring the electrical impedance at the piezoelectric patch bonded on a structure, an equivalent electrical model is constructed near the system resonance frequency. After shunting elements are connected to the equivalent circuit, the shunt parameters are optimally searched based on the criterion of maximizing the dissipated energy at the shunt circuit. Transmitted sound reduction performance is compared according to different piezoelectric materials with peizo-damping. Two piezoelectric materials are selected: PZT-5 and QuickPack IDE actuator. When resonant shunt circuit is considered, the use of PZT-5 exhibited the good sound reduction performance.