• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.438-440
• /
• 1995

The impedance characteristics and plasma parameters were experimentally studied in a weakly magnetized planar type, inductively coupled plasma (ICP) system. Compared with non-magnetized for system higher power transfer efficiency, stable impedance matching, enhancement of plasma density and higher electron temperature can be obtained. Such improvements are mainly due to the excitation of deeply penetrating electromagnetic wave and reduction of radial loss of electrons. In particulary, $SF_6$ (sulfur hexafluride) plasma shows unstable impedance matching in non-magnetized ICP because electronegativity of $SF_6$ effects on plasma characteristics. But, magnetized inductively coupled $SF_6$ plasma shows enough impedance matching stability to be applicable to the polysilicon etching in semiconductor process.

• Korean Journal of Materials Research
• /
• v.13 no.10
• /
• pp.658-662
• /
• 2003

In this study, we have tried to find the optimized design variables of the matching layer which is important part of thickness mode ultrasonic transducer and finally reach the conclusion that the electrical property of piezo-element must be under consideration when the optimized acoustic impedance is estimated. Proper expression of the effective impedance of front load at free resonant frequency(: $Z_{f}$ $^{(0)}$ /) has been induced by introducing the principle of binomial multilayer transformer and gradient based numerical method is utilized to find the most acceptable value of $Z_{ f}$/$^{(0)}$ . Optimized point of acoustic impedance can be calculated directly from $Z_{f}$ $^{(0)}$ using some simple formula which we propose. We also verify our result by both numerical and experimental method and get a good enhancement especially it concern to the bandwidth of ultrasonic transducer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.237-242
• /
• 2002

In this paper, active inverter bandpass filters using the impedance matching method are designed and fabricated. The designed active inverter bandpass filter is fabricated using microstrip-lines matching networks for IMT-2000 applications. Measured results show that the two-pole inverter bandpass filter for IMT-2000 application has its insertion gain of 14.1 ㏈, 75 MHz bandwidth at the center frequency 2.18 GHz and more than 23 ㏈ attenuation at fo $\pm$ 200 MHz.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.68 no.2
• /
• pp.304-309
• /
• 2019

This paper presents a CMOS RF-to-DC converter for video surveillance disposable IoT applications. It widely harvests RF energy of 3G/4G cellular low-band frequency range by employing a tunable impedance matching network. The proposed converter consists of the differential-drive cross-coupled rectifier and the matching network with a 4-bit capacitor array. The proposed converter is designed using 130-nm standard CMOS process. The designed energy harvester can rectify the RF signals from 700 MHz to 900 MHz. It has a peak RF-to-DC conversion efficiency of 72.25%, 64.97%, and 66.28% at 700 MHz, 800 MHz, and 900 MHz with a load resistance of 10kΩ, respectively.

• Journal of electromagnetic engineering and science
• /
• v.11 no.3
• /
• pp.152-155
• /
• 2011

This paper describes the role of mutual impedance and the transducer power gain which comes from key parameters to determine the amount of wireless power especially in a near-field environment. These two key parameters are applied to the two configurations; one is a dipole-dipole, and the other is a dipole-metal plate-loop configuration. Discussions are given on the achievable maximum power transfer between the sender and the receiver affected by the matching and the pass blockage.

• Proceedings of the KIEE Conference
• /
• 1985.07a
• /
• pp.224-227
• /
• 1985

During operation of an RF glow discharge system, it can be observed that the reflected power tends to increase in small value, due to changes in the impedance of the system. This problem can be relieved by adding an automatic impedance matching circuit to the system. This paper presents a detailed method of automatically matching the input impedance of a 50 ohm transmission line to an RF glow discharge system at 13.56 MHZ.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.11 no.6
• /
• pp.38-43
• /
• 1974

A design problem is studied for a nonuniform transmission line (NUTL) section to be inserted between an arbitrary source impedance and an arbitary load impedance for the purpose of impedance matching or providing a minimum input reflection coefficient over a frequency ranee as wide as possible. A special class of NUTL's, yet comprehensive enough to include almost all smoothly varying lines, are considered. Power series expansions of the ABCD parameters of such lines are used in the calculation of the input reflection coefficient. The design problem is formulated as a nonlinear programming problem withnonlinear constraints and is solved by a combined use of the sequential unconstrained minimization technique and tile Fletcher-Powell method. As a result, a line section was obtained which shows a marked improvement over any one hitherto published as a wide-band impedance matching device.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.3
• /
• pp.283-291
• /
• 2015

In this paper, a negative impedance converter, the key element of non-Foster matching to enhance the bandwidth of matching high Q-factor passive element, is presented. Proposed negative impedance converter is implemented by the topology of Linvill's transistor negative impedance converter circuit. It is hard to forecast the operation of negative impedance circuit, because it is composed of gain element and positive feedback. Therefore the negative impedance circuit is implemented by hybrid type beforehand to check out the feasibility and it is designed by integrated circuit. The integrated circuit is fabricated by commercial $0.18{\mu}m$ SiGe BiCMOS process, and non-Foster matching is observed at 700~960 MHz band by cancelling the target reactance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.4
• /
• pp.661-668
• /
• 2012

A coaxial-cable impedance transformer that can be used in high power and wideband frequency range is an arbitrary impedance transformation ratio by an additional coaxial cable. The coaxial-cable impedance transformer to be 50-${\Omega}$ to 25-${\Omega}$ impedance transformation ratio is easily operated an wideband power divider by connecting two 50-${\Omega}$ lines at 25-${\Omega}$ impedance point. This wideband power divider has a poor output matching characteristic and a poor isolation characteristic between two output ports. In this paper, it proposes a coaxial-cable power divider to be a good output matching and isolation characteristics as it uses the singly terminated filter design theory. The odd-mode operation characteristic of the suggested power divider to use singly terminated low pass filter coefficient due to matching order and ripple value is examined by ADS program. And, it fabricates and measures the operation characteristic of 2-way power divider with 2nd-order and 4th-order matching circuit.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.7
• /
• pp.1139-1146
• /
• 2001

A tapered impedance-matching line is designed by an inverse scattering method for the one-dimensional medium. The phase compensation factor(PCF) is introduced in order to reduce the error in the inverse scattering process to reconstruct the permittivity profile. By estimating the permittivity profile of the virtual one-dimensional dielectric medium whose reflection characteristic is the same as that of the specified matching line, the matching line is synthesized. The method can be used to design impedance-matching lines with arbitrary passband characteristics without any equivalent circuit analysis. The inevitable errors in the method using the time-domain reflection coefficient can be avoided by using the frequency-domain reflection coefficient.