• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.1
• /
• pp.24-29
• /
• 2001

PZT thin films(4000A) have prepared onto 1737 corning glass and ITO coated glass substrates with a RF magnetron sputtering system using Pb_{1.05}(Zr_{0.52},Ti_{0.48})O_3$ceramic target, Electrical properties of PZT thin film deposited after ITO coated glass were P${\gamma}$ was decreased by 25% after 109cycles, respectively. With the RTA treatment duration and temperature increased, the crystallization of PZT thin films were enhanced, however, the leakage current density became higher. The leakage current mechanism was found to be space charge conduction by the defects and oxygen vacancies existing in PZT and PZT/bottom electrode interfaces.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1477-1479
• /
• 2000

The annealing treatments on rf magnetron sputtered PZT($Pb_{1.05}(Zr_{0.52},Ti_{0.48})O_3$) thin films(4000${\AA}$) have been investigated for a structure of PZT/Pt/Ti/ITO coated glass. Crystallization properties of PZT films were strongly dependent on RTA(Rapid Thermal Annealing) annealing temperature and time. We were able to obtain a perovskite structure of PZT at 650$^{\circ}C$ and 10min. P-E curves of Pd/PZT/Pt capacitor demonstrate typical hysteresis loops. The measured values of $P_r$, $E_c$ were 15.8[${\mu}C/cm^2$], 95[kV/cm] respectively. Polarization value decrease about 10% after $10^9$ cycles.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.139-145
• /
• 2007

This paper presents the low cycle thermal fatigue of the engine exhaust manifold subject to thermomechanical cyclic loadings. The analysis includes the FE model of the exhaust system, temperature dependent material properties, and thermal loadings. The result shows that at an elevated temperature, large compressive plastic deformations are generated, and at a cold condition, tensile stresses are remained in several critical zones of the exhaust manifold. From the repetitions of thermal shock cycles, plastic strain ranges could be estimated by the stabilized stress-strain hysteresis loops. The method was applied to assess the low cycle thermal fatigue for the engine exhaust manifold. It shows a good agreement between numerical and experimental results.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.84-87
• /
• 2020

The properties of ultra-thin two-dimensional (2D) organic ferroelectric Langmuir-Blodgett (LB) films of the poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] were investigated to find possible applicability in flexible and wearable electronics applications. In the C-V characteristics of the MFM capacitor of 2-monolayer of 5 nm films, a butterfly hysteresis curve due to the ferroelectricity of P(VDF-TrFE) was confirmed. Typical residual polarization value was measured at 2μC/㎠. When the MFM capacitor with ultra-thin ferroelectric film was measured by applying a 10 Hz bipolar pulse, it was shown that 65% of the initial polarization value in 105 cycles deteriorated the polarization. The leakage current density of the 2-monolayer film was maintained at about 5 × 10-8 A/㎠ for the case at a 5MV/cm electric field. The resistivity of the 2-monolayer film in the case at an electric field at 5 MV/cm was more than 2.35 × 1013 Ω·cm.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.176-176
• /
• 2010

One of the critical issues for applications of flexible organic thin film transistors (OTFTs) for flexible electronic systems is the electrical stabilities of the OTFT devices, including variation of the current on/off ratio (Ion/Ioff), leakage current, threshold voltage, and hysteresis under repetitive mechanical deformation. In particular, repetitive mechanical deformation accelerates the degradation of device performance at the ambient environment. In this work, electrical stability of the pentacene organic thin film transistors (OTFTs) employing multi-stack hybrid encapsulation layers was investigated under mechanical cyclic bending. Flexible bottom-gated pentacene-based OTFTs fabricated on flexible polyimide substrate with poly-4-vinyl phenol (PVP) dielectric as a gate dielectric were encapsulated by the plasma-deposited organic layer and atomic-layer-deposited inorganic layer. For cyclic bending experiment of flexible OTFTs, the devices were cyclically bent up to 105 times with 5mm bending radius. In the most of the devices after 105 times of bending cycles, the off-current of the OTFT with no encapsulation layers was quickly increased due to increases in the conductivity of the pentacene caused by doping effects from $O_2$ and $H_2O$ in the atmosphere, which leads to decrease in the Ion/Ioff and increase in the hysteresis. With encapsulation layers, however, the electrical stabilities of the OTFTs were improved significantly. In particular, the OTFTs with multi-stack hybrid encapsulation layer showed the best electrical stabilities up to the bending cycles of $10^5$ times compared to the devices with single organic encapsulation layer. Changes in electrical properties of cyclically bent OTFTs with encapsulation layers will be discussed in detail.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.11
• /
• pp.765-770
• /
• 2001

Metal-ferroelectric-insulator- semiconductor(MFTS) devices by using rapid thermal annealed (RTA) LiNbO$_3$/AIN/Si(100) structures were successfully fabricated and demonstrated nonvolatile memory operations. Metal-insulator-semiconductor(MIS) C-V properties with high dielectric AIN thin films showed no hysteresis and good interface properties. The dielectric constant of the AIN film calculated from the capacitance at the accumulation region in the capacitance-voltage(C-V) characteristics was about 8. The C-V characteristics of MFIS capacitor showed a hysteresis loop due to the ferroelectric nature of the LiNbO$_3$ thin films. Typical dielectric constant value of LiNbO$_3$ film of MFIS device was about 23. The memory window width was about 1.2 V at the gate voltage of $\pm$5 V ranges. Typical gate leakage current density of the MFIS structure was the order of 10$^{-9}$ A/$\textrm{cm}^2$ at the range of within $\pm$500 kV/cm. The ferroelectric capacitors showed no polarization degradation up to about 10$^{11}$ switching cycles when subjected to symmetric bipolar voltage pulse(peak-to-peak 8 V, 50 % duty cycle) in the 500 kHz.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.3
• /
• pp.149-155
• /
• 2006

This paper presents a torsional micromirror detached from PZT actuators (TMD), whose rotational motion is achieved by push bars in the PZT actuators detached from the micromirror. The push bar mechanism is intended to reduce the bending, tensile and torsional constraints generated by the conventional bending bar mechanism, where the torsional micromirror is attached to the PZT actuators (TMA). We have designed, fabricated and tested prototypes of TMDs for single-axis and dual-axis rotation, respectively. The single-axis TMD generates the static rotational angle of $6.1^{\circ}$ at 16 VDC, which is 6 times larger than that of single-axis TMA, $0.9^{\circ}$. However, the rotational response curve of TMD shows hysteresis due to the static friction between the cover and the push bar in the PZT actuator. We have shown that 63.2% of the hysteresis is due to the static friction caused by the initial contact force of the PZT actuaor. Without the initial contact force, the rotational response curve of TMD shows linear voltage-angle characteristics. The dual-axis TMD generates the static rotational angles of $5.5^{\circ}$ and $4.7^{\circ}$ in x-axis and y-axis, respectively at 16 VDC. The measured resonant frequencies of dual-axis TMD are $2.1\pm0.1$ kHz in x-axis and $1.7\pm0.1$ kHz in y-axis. The dual-axis TMD shows stable operation without severe wear for 21.6 million cycles driven by 16 Vp-p sinusoidal wave signal at room temperature.

• The korean journal of orthodontics
• /
• v.48 no.6
• /
• pp.384-394
• /
• 2018

Objective: This study was performed to investigate an appropriate degree of prestretch for orthodontic synthetic elastomeric chains focusing on time-dependent viscoelastic properties. Methods: Orthodontic synthetic elastomeric chains of two brands were prestretched to 50, 100, 150, and 200% of the original length in one and three cycles, and the hysteresis areas of the obtained stress-strain curves were determined. Acrylic plates were employed to maintain constant strain during the experiment. A total of 180 samples were classified into nine groups according to brand, and their stresses and permanent deformations were measured immediately after prestretch (0 hour), after 1 hour and 24 hours, and after 1, 2, 3, 4, 5, 6, 7, and 8 weeks. The relationship between stress relaxation and permanent deformation was investigated for various degrees of prestretch, and the estimated stress resulting from tooth movement was calculated. Results: The degree of prestretch and the stress relaxation ratio exhibited a strong negative correlation, whereas no correlation was found between the degree of prestretch and the average normalized permanent strain. The maximal estimated stress was observed when prestretch was performed in three cycles to 200% of the original length. Conclusions: Although prestretch benefited residual stress, it did not exhibit negative effects such as permanent deformation. The maximal estimated stress was observed at the maximal prestretch, but the difference between prestretch and control groups decreased with time. In general, higher residual stresses were observed for product B than for product A, but this difference was not clinically significant.

• Steel and Composite Structures
• /
• v.15 no.3
• /
• pp.281-298
• /
• 2013

Composite special moment frame is one of the systems that are utilized in areas with low to high seismicity to deal with earthquake forces. Composite moment frames are composed of reinforced concrete columns (RC) and steel beams (S); therefore, the connection region is a combination of steel and concrete materials. In current study, a three dimensional finite element model of composite connections is developed. These connections are used in special composite moment frame, between reinforced concrete columns and steel beams (RCS). Finite element model is discussed as a most reliable and low cost method versus experimental procedures. Based on a tested connection model by Cheng and Chen (2005), the finite element model has been developed under cyclic loading and is verified with experimental results. A good agreement between finite element model and experimental results was observed. The connection configuration contains Face Bearing Plates (FBPs), Steel Band Plates (SBPs) enveloping around the RC column just above and below the steel beam. Longitudinal column bars pass through the connection with square ties around them. The finite element model represented a stable response up to the first cycles equal to 4.0% drift, with moderately pinched hysteresis loops and then showed a significant buckling in upper flange of beam, as the in test model.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.3
• /
• pp.130-132
• /
• 2013

$Bi_{3.25}La_{0.75}Ti_3O_{12}$(BLT) thin films were prepared on the Pt(150 nm)/Ti(50 nm)/$SiO_2$/Si substrate using the rf magnetron sputtering method. The BLT thin films were annealed at temperatures ranging from $600^{\circ}C$ to $750^{\circ}C$ using the rapid thermal annealing. The structure and surface morphology of the thin films were characterized by x-ray diffraction and field emission scanning electron microscopy. The hysteresis loop of the BLT thin films showed that the remanent polarization (2Pr) of the film annealed at $700^{\circ}C$ was 10.92 ${\mu}C/cm^2$. The fatigue characteristic of the BLT thin film annealed at $700^{\circ}C$ was shown change polarization up to $1.2{\times}10^9$ switching cycles. We confirmed the excellent remnant polarization (Pr) and fatigue properties compared with other fabrication methods and suggested a good method for BLT thin films fabrications.