• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2004년도 임시총회 및 추계학술발표회
• /
• pp.312-316
• /
• 2004

Single-well tracer tests, especially push pull tracer tests, are more effective to estimate hydraulic parameters and microbial metabolic activities in terms of duration and cost compared to multi-well tracer tests. However, there are some drawbacks in accuracy, complicated data analysis and uniqueness. These shortages are thought to be derived from the applied conditions which affect mass recovery curve and breakthrough curve. Factors such as extraction rate, resting period, hydraulic conductivity and hydraulic gradient are considered as the major factors determining the mass recovery rate and shape of the breakthrough curve. The results of the sensitivity analysis are summarized as follows: 1) the significant change in concentration of breakthrough curve is obtained when the extraction rate increases. This effect would also be much higher if the hydraulic conductivity is lower; 2) the mass recovery rate decreases with the increase of resting time, and the difference of mass recovery rates for different resting times is inversely proportional to the hydraulic conductivity; 3) the sensitivity values decrease with time. The hydraulic conductivity affects not only the early period, but the later period of the breakthrough curves; 4) The influence of the hydraulic gradient on the breakthrough curves is greater at earlier stage than at later stage. The mass recovery rate is inversely proportional to the hydraulic gradient.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2005년도 총회 및 춘계학술발표회
• /
• pp.446-450
• /
• 2005

Hydraulic conductivity of unconsolidated media can be determined by aquifer tests, laboratory tests and empirical equations based on grain size analysis. Commonly, the different methods give different hydraulic conductivities. Grain size measurements were done to determine hydraulic conductivity, using 184 soil samples collected from eight boreholes in a riverbank filtration area, Daesan-Myeon, Changwon City, Korea, Pumping tests were conducted at the riverbank filtration area. The average hydraulic conductivity by the empirical relations from grain size measurements comes out around $10^{-2}m/s$, 22 to 55 times higher than by the pumping test analyses. The hydraulic conductivity obtained from the empirical equations is interpreted to have a relationship with steady-state condition while that obtained from the pumping tests is interpreted to have a relationship with unsteady-state condition. Thus, hydraulic conductivity obtained from various methods should be critically analyzed for reasonable management of groundwater development.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2004년도 총회 및 춘계학술발표회
• /
• pp.341-345
• /
• 2004

An attempt has been made in this study to evaluate an applicability of Relative Effective Porosity Model (REPM) as a method for estimating saturated hydraulic conductivity (K$_{s}$) for homogeneous coarse, medium, and fine sands. The saturated hydraulic conductivities obtained from REPM are converted into average linear velocities using Darcy's Law and compared with the results from experimental tracer tests for homogeneous coarse, medium, and fine sand layer. Two types of tracer tests analyses, analytical solution using CXTFIT and moment methods, are performed to obtain reasonable linear velocity range for each layer. For the coarse and medium sands, the converted average linear velocity from REPM is in the velocity range obtained from tracer tests. However, small difference between the results from REPM and tracer tests is found for the fine sands. These results show that REPM gives reasonable estimates of saturated hydraulic conductivity.y.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 1999년도 Proceedings of the 1999 Annual Conference The Korean Society of Agricutural Engineers
• /
• pp.465-472
• /
• 1999

Hydraulic model tests are performed to find economical and hdrqulically stable design of cooling water intake channel of steam power plant. The result of tests show that the standard distributiion of y-components in the chamber of CWP(circulating Water Pump) are recommended below 3.5 to maintain hydraulic stability, so that this value is considered as the design criteria. Common basin is necessary to improve the hydraulic stability of inflow, however the longer basin does not always improve the hydraulic stability , and the optimal length of basin can be found in some range. From the results the flow stability maintained the best condition when the length of basin is 7.2m. Beside the standard tests the auxiliary tests like edge , baffle, trapezoidal section and increase of pump capacity are carried out based on the optimal condition foudn in the standard tests. From the series of tests the economical and hydraulically stable design of intake channel was proposed.

• 지질공학
• /
• 제28권1호
• /
• pp.1-9
• /
• 2018

We propose a borehole test technique to estimate permeability of rocks in borehole. The borehole tests are hydraulic injection tests such as leak-off test and hydraulic fracturing tests, which are originally conducted for stress or casing integrity assessment and not for permeability measurement. We use one-dimensional radial diffusion equation to interpret fluid injection test results in terms of permeability. We apply this technique to a leak-off test conducted at a depth of 700 m in a wellbore, where rock formation is mudstone. The estimated permeability is at an order of $10^{-16}m^2$, which is somewhat high but within the range reported for mudstones previously. Quantitative rick assessment suggests that an accurate measurement of open hole section length is important to improve reliability of results. More data may be needed to ensure the reliability of this technique. If validated, however, this technique can provide cost-effective estimation of in situ permeability without conducting independent permeability tests in borehole.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.183-190
• /
• 2000

Effective range of Hydraulic Hammer Compaction was studied by numerical analysis instead of empirical method. Numerical analyses were carried out with commercial FEM code, ABAQUS, and verified by comparing the numerical results with field tests of Hydraulic Hammer Compaction. Most of material properties were evaluated by data from laboratory and in-situ tests. Vertical effective range was estimated by distribution curve of plastic strain energy dissipated through soil layers under dynamic load and these results were in good agreement with field tests. Based on verification, the effects of governing properties of Hydraulic Hammer Compaction such as number of hit can be determined by numerical analyses. In addition, vertical effective range can also be determined by Menard's empirical equation using the external work at converging time of plastic strain energy in numerical analysis. This implies that the minimum energy of Hydraulic Hammer Compaction for improvement can be determined by Menard's equation.

• 터널과지하공간
• /
• 제8권2호
• /
• pp.79-86
• /
• 1998

This study was performed to suggest to suggest suitable design conditions of water curtain system through analysis on pressure down in boreholes by hydraulic tests carried out I construction fields for underground oil storages. The influence by hydraulic conductivities of rock mass around boreholes on pressure down in boreholes was analysed. The relationship between array of boreholes and their pressure down was also analysed. Groundwater flow analysis on crude oil and LPG storages was carried out to evaluate results of field tests and to investigate distribution of hydraulic gradient in rock mass around cavern using finite difference method. As the results, hydraulic tests showed that pressure down in boreholes was inverse proportional to the hydraulic conductivity of surrounding rock mass. The rate of pressure down of boreholes was not influenced by water curtain system more than 20m over cavern and was proportional to installation interval of boreholes. The hydraulic gradient in rock mass around cavern was proportional to distance and interval of boreholes and its value was not satisfactory to oil tightness condition in case of no water curtain system.

• 터널과지하공간
• /
• 제23권5호
• /
• pp.362-371
• /
• 2013

수압파쇄법으로 최대수평주응력 크기 규명에 필요한 요소 중 하나인 암반의 인장강도를 측정하는 방법에 대해 연구하였다. 석모도 시추공에서 회수한 화강암 시료에 대해 두 가지 실내시험(중공원통 인장시험 및 압열인장시험)으로 인장강도를 측정하고 두 결과가 차이를 보이는지 비교하였다. 중공원통 인장시험에서는 높은 수압증가율 상태에서 더 높은 인장강도를 보여, 현장의 수압파쇄시험에서 보인 수압 증가율 상태에서 측정된 인장강도나 그 증가율로 보정된 인장강도를 이용해야한다는 점을 보였다. 인장강도에 대한 수압 증가율 효과와 크기효과를 보정하면 중공원통 인장시험 결과는 압열인장시험 결과와 유사하게 나타났으며 이는 수압파쇄 인장강도를 위해 압열인장강도를 이용할 수도 있다는 점을 시사한다.

• 지질공학
• /
• 제20권2호
• /
• pp.203-212
• /
• 2010

본 연구는 연구지역의 수리상수를 추정하여 오염된 지하수의 정화공법 설계에 효과적으로 사용하는데 목적이 있다. 이를 위하여 수행된 수리시험은 순간수위변화시험, 단공양수시험 및 단계양수시험이다. 순간수위변화시험은 대표적인 Bouwer and Rice 직선법과 C-B-P 특성곡선법(type curve)으로 해석하였다. Bouwer and Rice법으로 해석한 평균 수리전도도 값은 $4.48{\times}10^{-3}cm/sec$ 이며 중앙값은 $1.16{\times}10^{-3}cm/sec$이다. C-B-P법으로 구한 평균 수리전도도 값은 $2.37{\times}10^{-3}cm/sec$이며 중앙값은 $7.09{\times}10^{-4}cm/sec$이다. 두 해석 결과 연구지역의 하부가 화강암으로 이루어져 있어 대체로 투수성이 낮아 Bouwer and Rice법으로 해석한 수리전도도가 높게 나타난다. 단공양수시험은 GW7, GW12 및 MW9 관정에서 수행하였으며 여러 종류의 특성곡선법을 적용하여 해석하였다. GW7 관정은 GW12 및 MW9 관정보다 수리전도도 및 투수량 계수가 낮으며 이는 기반암의 파쇄대 및 절리의 여부와 관련된 것으로 판단된다. 단계양수시험은 KDPW1 및 KDPW2 관정에서 수행하였으며 해석방법에 따라 수리상수 값의 차이가 나타나지만 매우 미미하며 본 연구에서 해석한 수리상수 값은 오염지하수 정화설계에 있어 적절히 활용될 것으로 판단된다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.523-526
• /
• 2006

A series of hydraulic and cavitation tests are performed in water environment in order to verify the hydraulic and cavitation performance of three types of LOX pumps. All the performances of the pumps are found to be satisfied with each design requirement. In the hydraulic tests, the head and efficiency are increased as the gap between floating ring seals and the impeller shoulder is decreased. In the cavitation tests, some pumps show decrease in the cavitation performance as the flowrate of the pump is decreased.