• 한국통신학회논문지
• /
• 제37권6B호
• /
• pp.443-452
• /
• 2012

Mobile Ad-hoc Networks 환경에서 노드의 이동성을 고려하기 위한 라우팅 알고리즘은 그 특성에 따라 Proactive와 Reactive 방식으로 구분되며, 두 가지 라우팅의 장점을 조합하는 많은 Hybrid 라우팅이 ZRP (Zone Routing Protocol) 알고리즘을 기반으로 설계되어왔다. ZRP는 특정 지역의 Zone을 생성한 후, Zone 내부에는 Proactive, 외부에는 Reactive 방식을 운영하여 근거리 노드들을 향하는 데이터의 경로 탐색 패킷 발생의 비용을 최소화 하였다. 하지만 실제 네트워크에서의 데이터 전송은 짧은 시간 영역에서 특정 노드에게만 요구되는 경향이 있으며, 이에 대한 고려가 없는 ZRP는 이러한 요구를 만족시키기에는 제한적이다. 본 연구는 실시간 데이터 전송량과 전송 경로의 홉 수를 고려하여, 소스 노드와 목적지 노드를 근간으로 하는 Zone을 on-demand로 형성하는 효율적인 Hybrid 라우팅을 제안하고, 이를 위하여 Zone의 생성 및 소멸을 결정하는 DZD (Dynamic Zone Decision) 알고리즘을 고안한다. 또한, 본 연구의 성능을 검증하기 위하여 기존의 Proactive, Reactive, Hybrid 라우팅 알고리즘과의 비교결과를 분석하였다.

• 한국공간구조학회논문집
• /
• 제21권1호
• /
• pp.71-78
• /
• 2021

The U-flanged truss hybrid beam is a new composite beam made by pouring concrete into the U-flanged truss beam. In this study, an experimental study was performed to verify the shear capacity of U-flanged truss hybrid beams with the newly developed end reinforcement details. For all specimens, the maximum shear strength was determined by shear failure of concrete in the loading point The detail reinforced with stirrups at the end zone can exhibit the greatest shear strength, but the method of reinforcing the end zone using vertical steel plates, which is a relatively easy method to manufacture, is considered to be the most effective detail in terms of shear strength and ductility. Also, in the case of U-flanged truss hybrid beams reinforced with vertical steel plates at the end zone, the shear strength can be evaluated on the safety side by using the Korea Design Standard formula.

• 동력기계공학회지
• /
• 제15권1호
• /
• pp.45-50
• /
• 2011

The effect of Mn and Ti contents in filler wire on the microstructure and mechanical property of weld metal has been investigated after hybrid welding with ultra fine grained (UFG) steel. The microstructure and distribution of alloy compositions at the top region of weld zone were quite different with those at the bottom region after hybrid welding. The bottom region of weld zone contained higher Mn and Ti contents, and consequently the hardness of bottom region was higher than that of top region. With the increase of Mn and Ti contents in filler wire, the volume percent of acicular ferrite in weld metal decreased, and the weld zone showed higher hardness and better impact property.

• 동력기계공학회지
• /
• 제14권3호
• /
• pp.58-63
• /
• 2010

A laser beam welding and an electric arc welding were combined, and the positive points of each welding method are drawn such as high speed, low thermal load, deep penetration, and high productivity. The fiber laser-MIG conjugated welding. namely the hybrid welding has been studied mainly for the automation industry of a pipeline welding. In this study, the MIG welding was combined with a fiber laser welding to make up the hybrid welding. The weld shapes, microstructures and mechanical properties for weld zones after the hybrid welding or only fiber laser welding were investigated on the 700 MPa grade Ultra Fine Grained(UFG) high strength steel. The amount of acicular ferrite in weld metals and HAZ(heat affected zone) was observed larger after hybrid welding compared with after only laser welding. The Vickers hardness of the top area of the fusion zone after fiber laser welding was higher compared with after hybrid welding.

• 한국항공운항학회지
• /
• 제23권4호
• /
• pp.1-5
• /
• 2015

In this work, a study was conducted to investigate the effect of diaphragm thickness on the regression rate of the hybrid rocket motor. To observe the flow pattern and the recirculation zone, visualizations of combustion chambers with different diaphragm thickness (5mm, 10mm) were performed. It was found that the case with 5 mm thickness had a larger recirculation zone and therefore, had a higher regression rate than the case with 10mm thickness due to the increased residence time and heat transfer toward the fuel surface. Finally, it was concluded that the thickness of diaphragm can be a critical parameter for the enhancement of the regression rate.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.1137-1143
• /
• 2006

The purpose of this research lays on examining the adequacy of the hybrid ventilation system. The hybrid ventilation system must satisfy the next to be used. Firstly, the cold-draft phenomenon must not exist in the occupied zone. Secondly, the condensation must not happen on the surfaces of vents. Thirdly, the flow of make-up air must be happened in an each space by exhausted air of a rest room and living room. We used an examination and CFD method to verify these. Trough the examination of air-vents, We confirmed that the cold-draft to be induced by make-up air does not happen and could not find the condensation in the limits of outdoor temperature higher than 265K. Through CFD simulation, We confirmed that the rapid temperature change existed only within 0.5m the occupied zone and the flow of air was happened in an each space by only exhausted air in the rest room and living room. Consequently, the hybrid system is possible method to an apartment house.

• 대한지리학회지
• /
• 제41권1호
• /
• pp.121-135
• /
• 2006

공시지가 유사가격권의 경우는 비교표준지 선정시 지침상에서 상당히 중요한 요소로 취급되고 있으면서도 실제적으로는 범위와 적용에 관해서 모호한 개념상의 규정을 두고 있다. 이러한 원인에 기인하여 비교표준지의 자동 선정이나 공시지가의 자동 산정에 있어 많은 문제점으로 작용하고 있다. 따라서 신속하고 정확한 비교표준지의 선정과 향후 지가산정 일련의 과정을 전산화하기 위해서는 자동화된 방식으로 유사가격권을 구획할 수 있는 객관적이고 합리적인 방법론이 필요하다. 본 연구에서는 개별공시지가 산정시 유사가격권 설정의 문제를 해결하고자 평균연결법과 K-means 혼합클러스터링 기법을 활용하여 유사가격권을 설정하여보고 이에 대한 타당성을 제시하고자 하였다. 이를 위해 실제 사례지역을 선정하고 실험한 결과 유사가격 권역 별로 군집화가 가능하였고, 현행 유사가격 권역과 많은 차이를 보이지 않아 방법론의 타당성을 제시할 수 있었다.

• Advances in aircraft and spacecraft science
• /
• 제5권5호
• /
• pp.595-613
• /
• 2018

The objective of our study is to analyze the behavior of bonded, riveted and hybrid (bonded / riveted) steel / steel assemblies by tensile tests and to show the advantage of a hybrid assembly over other processes. the finite element method with the ABAQUS numerical code was used to model the fracture behavior of the different assemblies. Cohesive zone models (CZM) have been adopted to model crack propagation in bonded joints using a bilinear tensile separation law implemented in the ABAQUS finite element code. The riveted assemblies were modeled with the XFEM damage method identified in this ABAQUS numerical code. Both CZM and XFEM methods are combined to model hybrid assemblies. The results are consistent with the experimental results and make it possible to guarantee the validity of the applied numerical model. The use of a hybrid assembly shows a high resistance compared to other conventional methods, where the number of rivets has been highlighted. The use of the hybrid assembly improves mechanical strength and increases service life compared to a single lap joint and a riveted joint.

• 대한기계학회논문집A
• /
• 제37권3호
• /
• pp.397-403
• /
• 2013

친환경 및 연비에 대한 요구와 제한은 하이브리드 차량과 같은 친환경 고연비 차량기술을 발전시켜왔다. 하이브리드 차량의 연비는 시스템의 특성으로 인해 주행 후 배터리 충전량의 변화를 연비에 반영시키는 등가연료사용량이 연료소비량에 추가되므로 제어전략에서 배터리 사용영역 증가만으로 연비를 향상시킬 수 없었다. 본 논문은 연료전지 하이브리드 차량을 matlab simulink상에서 모델링하고 기존제어전략에서 연료전지의 사용구간을 분석하여 연료전지 주 사용영역에서의 배터리와 연료전지 간 동력분배를 연비향상을 목표로 최적화하여 등가연료사용량을 포함한 총연비의 향상을 시도하였다.

• 한국해양공학회지
• /
• 제24권6호
• /
• pp.16-22
• /
• 2010

In this paper, the diffraction problems for fixed offshore structures are solved using a hybrid scheme. In this hybrid scheme, potential-based solutions and the Navier-Stokes-based finite volume method (FVM) with a volume-of-fluid (VOF) method are combined. We introduce a buffer zone for efficient wave-making and damping. In this buffer zone, the near field solution from FVM-VOF is gradually changed to Stokes' 2nd order wave solutions. Three different models, including the truncated cylinder, sphere, and wigleyIII model, are numerically investigated in regular waves with a wave steepness of 1/30. The efficiency and accuracy of the hybrid scheme are numerically validated from results using different domain sizes and buffer zones. The wave exciting forces from the FVM-VOF simulations are compared with experiments and potential-based solutions from the higher-order boundary element method (HOBEM). This comparison shows good agreement between the hybrid scheme and potential-based solutions.