Browse > Article
http://dx.doi.org/10.12989/aas.2018.5.5.595

Damage of bonded, riveted and hybrid (bonded/riveted) joints, Experimental and numerical study using CZM and XFEM methods  

Ezzine, M.C. (Laboratoire Mecanique Physique des Materiaux (LMPM), Department of Mechanical Engineering, University of Sidi Bel Abbes)
Amiri, A. (Laboratoire Mecanique Physique des Materiaux (LMPM), Department of Mechanical Engineering, University of Sidi Bel Abbes)
Tarfaoui, M. (ENSTA Bretagne, MSN/LBMS/DFMS)
Madani, K. (Laboratoire Mecanique Physique des Materiaux (LMPM), Department of Mechanical Engineering, University of Sidi Bel Abbes)
Publication Information
Advances in aircraft and spacecraft science / v.5, no.5, 2018 , pp. 595-613 More about this Journal
Abstract
The objective of our study is to analyze the behavior of bonded, riveted and hybrid (bonded / riveted) steel / steel assemblies by tensile tests and to show the advantage of a hybrid assembly over other processes. the finite element method with the ABAQUS numerical code was used to model the fracture behavior of the different assemblies. Cohesive zone models (CZM) have been adopted to model crack propagation in bonded joints using a bilinear tensile separation law implemented in the ABAQUS finite element code. The riveted assemblies were modeled with the XFEM damage method identified in this ABAQUS numerical code. Both CZM and XFEM methods are combined to model hybrid assemblies. The results are consistent with the experimental results and make it possible to guarantee the validity of the applied numerical model. The use of a hybrid assembly shows a high resistance compared to other conventional methods, where the number of rivets has been highlighted. The use of the hybrid assembly improves mechanical strength and increases service life compared to a single lap joint and a riveted joint.
Keywords
single lap joint; riveted joint; hybrid joint; cohesive zone model (CZM); XFEM; steel E24;
Citations & Related Records
Times Cited By KSCI : 2  (Citation Analysis)
연도 인용수 순위
1 Elhannani, M., Madani, K., Legrand, E., Touzain, S. and Feaugas, X. (2017), "Numerical analysis of the effect of the presence, number and shape of bonding defect on the shear stresses distribution in an adhesive layer for the single-lap bonded joint; Part 1", Aerosp. Sci. Technol., 62, 122-135.   DOI
2 Elhannani, M., Madani, K., Mokhtari, M., Feaugas, X., Touzain, S. and Cohendoz, S. (2016), "A new analytical approach for optimization design of adhesively bonded single-lap joint", Struct. Eng. Mech., 59(2), 313-326.   DOI
3 Fu, M. and Mallick, P. (2001), "Fatigue of hybrid (adhesive/bolted) joints in SRIM composites", J. Adhes. Adhes., 21(2), 145-159.   DOI
4 Gomez, S., Onoro, J. and Pecharroman, J. (2007), "A simple mechanical model of a structural hybrid adhesive/riveted single lap joint", J. Adhes. Adhes., 27(4), 263-267.   DOI
5 Harris, J.A. and Adams, R.A. (1984), "Strength prediction of bonded single lap joints by nonlinear finite element methods", J. Adhes. Adhes., 4(2), 65-78.   DOI
6 Hart-Smith, L.J. (1973), "Adhesive-bonded double-lap joints", NASA-CR-112235; Douglas Aircraft Co., Inc., CA, U.S.A.
7 Hart-Smith, L.J. (1985), "Bonded-bolted composite joints", J. Aircraft., 22(11), 993-1000.   DOI
8 Ireman, T., Nyman, T. and Hellbom, K. (1993), "On design methods for bolted joints in composite aircraft structures", Compos. Struct., 25(1-4), 567-578.   DOI
9 Karachalios, E.F., Adams, R.D. and da Silva, L.F.M. (2013a), "Single lap joints loaded in tension with high strength steel adherends", J. Adhes. Adhes., 43, 81-95.   DOI
10 Karachalios, E.F., Adams, R.D. and da Silva, L.F.M. (2013b), "Single lap joints loaded intension with ductile steel adherends", J. Adhes. Adhes., 43, 96-108.   DOI
11 Kelly, G. (2006), "Quasi-static strength and fatigue life of hybrid (bonded/bolted) composite single-lap joints", Compos. Struct., 72(1), 119-129.   DOI
12 Kweon, J., Jung, J., Kim, T., Choi, J. and Kim, D. (2006), "Failure of carbon composite-to-aluminum joints with combined mechanical fastening and adhesive bonding", Compos. Struct., 75(1), 192-198.   DOI
13 Lee, M., Cho, T., Kim, W., Lee, B. and Lee, J. (2010), "Determination of cohesive parameters for a mixedmode cohesive zone model", J. Adhes. Adhes., 30(5), 322-328.   DOI
14 Lee, M.H., Kim, H.Y., Oh, S.L. (2006), "Crushing test of double hat-shaped members of dissimilar materials with adhesively bonded and self-piercing riveted joining methods", Thin-Walled Struct., 44(4), 381-386.   DOI
15 Lees, W.A. (1985), "Stress distribution in bonded joints: an exploration within a mathematical model", Mater. Des., 6(3), 117-23.   DOI
16 Matthews, F.L., Kilty, P.F. and Goodwin, E.W. (1982), "A Review of the strength of joints in fibre reinforced plastics. Part 2 Adhesively bonded joints", Compos., 29-37.
17 Mokhtari, M., Madani, K., Belhouari, M., Touzain, S., Feaugas, X. and Ratwani, M. (2013), "Effects of composite adherend properties on stresses in double lap bonded joints", Mater. Design, 44, 633-639.   DOI
18 Peroni, L., Avalle, M. and Belingardi, G. (2009), "Comparison of the energy absorption capability of crash boxes assembled by spot-weld and continuous joining techniques", J. Impact Eng., 36(3), 498-511.   DOI
19 Reid, J.D. and Hiser, N.R. (2005), "Detailed modeling of bolted joints with slippage", Finite Elem. Anal. Des., 41(6), 547-562.   DOI
20 Rezgani, L., Madani, K. and Mokhtari, M., Feaugas, X., Cohendoz, S., Touzain, S. and Mallarino, S. (2018), "Hygrothermal ageing effect of ADEKIT A140 adhesive on the J-integral of a plate repaired by composite patch", J. Adhes. Sci. Technol., 32(13), 1393-1409.   DOI
21 Rezgani, L., Madani, K., Feaugas, X., Touzain, S. and Vallette, J. (2016), "Influence of water ingress onto the crack propagation rate in a AA2024-T3 plate repaired by a carbon/epoxy patch", Aerosp. Sci. Technol., 55, 359-365.   DOI
22 Russo, A. and Zuccarello, B. (2013), "Toward a design method for metal-composite co-cured joints based on the G-SIFs", Compos. Part B: Eng., 45(1), 631-643.   DOI
23 Sadowski, T., Knec, M. and Golewski, P. (2010), "Experimental investigations and numerical modelling of steel adhesive joints reinforced by rivets", J. Adhes. Adhes., 30(5), 338-346.   DOI
24 Seo, D.W., Lim, J.K. (2005), "Tensile, bending and shears strength distributions of adhesive-bonded butt joint specimens", Compos. Sci. Technol., 65(9), 1421-1427.   DOI
25 Thrall, Jr. and Edward, W. (1977), "Primary adhesively bonded structure technology (PABST)", J. Aircraft, 14(6), 588-594.   DOI
26 Thrall, Jr. and Edward, W. (1979), "PABST program test results", Adhes., 22(10), 22-33.
27 Tsai, M. and Morton, J. (1993), "Mechanics of a laminated composite single-lap joint", Mechanics Composites Rev.
28 Tsai, M. and Morton, J. (1995), "The effect of a spew fillet on adhesive stress distributions in laminated composite single-lap joints", Compos. Struct., 32(1-4), 123-131.   DOI
29 Vinson, J.R. (1989), "Adhesive bonding of polymer composites", Polym. Eng. Sci., 29(19), 1325-1331.   DOI
30 Tsai, M.Y. and Morton, J. (1994), "An evaluation of analytical and numerical solutions to the single-lap joint", Solids Struct., 31(18), 2537-2563.   DOI
31 Volkersen, O. (1938), "Die Nietkraftverteilung in Zugbeanspruchten Neitverbeindun- gen mit Konstanten Laschequerschnitten", Die Luftfahrtforschung, 15, 41-47.
32 Wooley, G.R. and Carver, D.R. (1971), "Stress concentration factors for bonded lap joints", J. Aircraft, 8(10), 817-820.   DOI
33 Zhang, F., Wang, H.P., Hicks, C., Yang, X., Carlson, B. and Zhou, Q. (2013a), "Experimental study of initial strengths and hygro thermal degradation of adhesive joints between thin aluminum and steel substrates", J. Adhes. Adhes., 43, 14-25.   DOI
34 Zhang, F., Yang, X., Wang, H.P., Zhang, X., Xia, Y. and Zhou, Q. (2013b), "Durability of adhesively- bonded single lap-shear joints in accelerated hygrothermal exposure for automotive applications", J. Adhes. Adhes., 44, 130-137.   DOI
35 Benchiha, A., Madani, K., Touzain, S. and Ratwani, M. (2016), "Numerical analysis of the Influence of the presence of disbond region in adhesive layer on the stress intensity factors (SIF) and crack opening displacement (COD) in plates repaired with a composite patch", Steel Compos. Struct., 20(4), 951-962.   DOI
36 Adams, R., Atkins, R., Harris, J. and Kinloch, A. (1986), "Stress analysis and failure properties of carbonfibre reinforced plastic/steel double lap-joint", J. Adhesion, 20(1), 29-53.   DOI
37 Adams, R.D. (2005), Adhesive Bonding: Science, Technology and Applications, Woodhead Publishing Ltd., Bristol, United Kingdom.
38 Adams, R.D. and Peppiatt, N.A. (1974), "Stress analysis of adhesive-bonded lap joints", J. Strain Analysis, 9(3), 185-196.   DOI
39 Al-Bahkali, E.A. (2011), "Finite element modeling for thermal stresses developed in riveted and rivetbonded joints", J. Eng. Technol., 11(06), 86-92.
40 Apalak, Z., Apalak, M. and Genc, M. (2006), "Progressive damage modeling of an adhesively bonded unidirectional composite single-lap joint in tension at the mesoscale level", J. Thermoplastic Compos. Mater., 19(6), 671-702.   DOI
41 Blackman, B.R.K., Kinloch, A.J., Taylor, A.C. and Wang, Y. (2000), "The impact wedge-peel performance of structural adhesives", J. Mater. Sci., 35(8), 1867-1884.   DOI
42 Chan, W.S. and Vedhagiri, S. (2001), "Analysis of composite bonded/bolted joints used in repairing", Compos. Mater., 35(12), 1045-1061.   DOI
43 Camanho, P.P. and Davila, C.G. (2002), "Mixed-mode decohesion finite elements for the simulation of delamination in composite materials", NASA/TM-2002-211737; NASA Langley Research Center, U.S.A.
44 Campilho, R.D.S.G., de Moura, M.F.S.F., Ramantani, D.A., Morais, J.J.L. and Domingues, J.J.M.S. (2009), "Buckling behaviour of carbon-epoxy adhesively-bonded scarf repairs", J. Adhes. Sci. Technol., 23(10-11),1493-1513.   DOI
45 Challita, G., Othman, R., Casari, P. and Khalil, K. (2011), "Experimental investigation of the shear dynamic behavior of double-lap adhesively bonded joints on a wide range of strain rates", J. Adhes. Adhes., 31(3), 146-153.   DOI
46 Collings, T.A. (1977), "The strength of bolted joints in multi-directional CFRP laminates", Composites, 8(1), 43-55.   DOI
47 da Silva, L.F.M. and Ochsner, A. (2008), Modeling of Adhesive Bonded Joints., Springer, Berlin, Germany.
48 da Silva, L.F.M., Carbas, R.J.C. and Critchlow, G.W. (2009), "Effect of material, geometry, surface treatment and environment on the shear strength of single lap joints", J. Adhes. Adhes., 29(6), 621-632.   DOI
49 De'Neve, B., Delamar, M., Nguyen, T.T. and Shanahan, M.E.R. (1998), "Failure mode and ageing of steel/epoxy joints", Appl. Surf. Sci., 134(1-4), 202-212.   DOI