• Restorative Dentistry and Endodontics
• /
• v.27 no.4
• /
• pp.403-410
• /
• 2002

Several ways of curing are being tried to improve material's properties and reduce marginal gap. However, all are considering about the pattern of light intensity. It was noted from the preliminary study the change of light wavelength from filter changing may give an impact on material's property and microleakage. The object of this study was to verify the effect of filters with various wavelength width on the microhardness and microleakage of composite resin ; hybrid type of DenFil and submicron hybrid type of Esthet X. Composite resins were cured using 3 kinds of filter; narrow-banded(465-475 nm), mid-banded(430-470 nm), wide-banded(400-500 nm). After the estimation of microhardness. degree of dye penetration and the maximum gap from SEM evaluation were done between 4 groups that showed no difference in microhardness value of the lower surface . The results were as follows : 1 Adequate microhardness could not be gained with a narrow-banded filter irrespective of curing time. At the upper surface, DenFil should be polymerized with middle or wide-banded filter for 20 seconds at least, while Esthet X be col$.$ed with middle or wide-banded filter for 30 seconds at least to get simitar hardness value to control group. 2. There was little dye penetration in enamel margin, but all dentin margins skewed much more dye penetration irrespective of curing conditions. Although there was no statistical difference, groups cured with mid-banded filter for 40 seconds and with wide-width filter for 20 seconds showed relatively less dye penetration. 3. It was revealed from the SEM examination that group cured with wide-banded filter had the smallest gap without statistical significance. Spearman's rho test showed that the correlation between the results of dye penetration and SEM examination was very low. From these results, it could be concluded that curing with wide-width filter would be better than the other techniques, even though the curing technique using mid-width filter seems to have its own unique advantage.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.4
• /
• pp.313-320
• /
• 2008

The dynamic clustering technique has some problems regarding energy consumption. In the cluster configuration aspect the cluster structure must be modified every time the head nodes are re-selected resulting in high energy consumption. Also, there is excessive energy consumption when a cluster head node receives identical data from adjacent cluster sources nodes. This paper proposes a solution to the problems described above from the energy efficiency perspective. The round-robin cluster header(RRCH) technique, which fixes the initially structured cluster and sequentially selects duster head nodes, is suggested for solving the energy consumption problem regarding repetitive cluster construction. Furthermore, the issue of redundant data occurring at the cluster head node is dealt with by broadcasting metadata of the initially received data to prevent reception by a sensor node with identical data. A simulation experiment was performed to verify the validity of the proposed approach. The results of the simulation experiments were compared with the performances of two of the must widely used conventional techniques, the LEACH(Low Energy Adaptive Clustering Hierarchy) and HEED(Hybrid, Energy Efficient Distributed Clustering) algorithms, based on energy consumption, remaining energy for each node and uniform distribution. The evaluation confirmed that in terms of energy consumption, the technique proposed in this paper was 29.3% and 21.2% more efficient than LEACH and HEED, respectively.

• Korean Journal of Construction Engineering and Management
• /
• v.17 no.3
• /
• pp.52-60
• /
• 2016

This study investigates and analyzes the total amount of energy consumption and $CO_2$ emission during the material manufacturing, transportation, construction, operation, and disposal phases of eight elementary school buildings in South Korea. Toward this ends, the hybrid LCA model is proposed. The life cycle energy consumption and $CO_2$ emission of eight case buildings are assessed using the hybrid LCA model with an assumption that the operation period is 40 years. As a result, the embodied(sum of the energy consumption in the material manufacturing, transportation and construction phases), operational and disposal energy were 2,279, 11,182, $228Mcal/m^2$, respectively, on average. The average embodied, operational, and disposal $CO_2$ emission were 604, 2,708, 60 kg-$CO_2/m^2$, respectively, on average. This result indicates that about 17% of life cycle energy (or $CO_2$ emission) is consumed in the material manufacturing, transportation and construction phases. Thus, it is necessary to consider the embodied energy and $CO_2$ emission to reduce the life cycle energy and $CO_2$ emission of school buildings. In addition, while the insulation standard of building have been provided based on the climate zone, energy consumption in operation phase still varied depending on the regions in this study. Thus, the insulation standard of building needs to be improved through considering the climate of regions in detail.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.4 s.71
• /
• pp.397-406
• /
• 2004

This paper presents the test and evaluation results on the shear strength and stiffness of a light steel stud wall from a lightweight foamed mortar (lightweight hybrid wall). The use of a lightweight foamed mortar was aimed at improving structural performance, thermal performance, and finish. Studiesshowed that it did not affect thermal performance, but it contributed to structural performance and finish when the unit weight was more than 0.8 (Editor's note: Please indicate the unit of measurement.). In this study, 14 specimens-whose parameters included the specific gravity of the lightweight foamed mortar (0.6, 0.8, 1.0, 1.2), the spacing of the stud (450 mm, 600 mm, or 900 mm), finishing materials (such as lightweight foamed mortar, OSB, and gypsum board), and bracing-were manufactured. Three typical, steel house-framing specimens were added to compare the test results with the 14 specimens. The results of in-plane shear tests show that the use of lightweight foamed mortar (1.15~5.38 times stronger, 1.45~13.7 times stiffer) results in ultimate strength and initial stiffness. In addition, it was possible to widen the stud spacing to up to 900 mm without decreasing shear strength. It was very important to prevent the lightweight foamed mortar from shrinking and to secure the adhesion between the steel stud and the lightweight foamed mortar to improve structural performance.

• Journal of Animal Science and Technology
• /
• v.44 no.5
• /
• pp.625-632
• /
• 2002

Livestock farmers face several limitations when using the government recommended sorghum cultivars for forage because of the limited seed supply. Therefore, the objective of the this study is to evaluate, select, and recommend the best high-yielding hybrid as the government recommended cultivars. The agronomic characteristics and forage yield of three cultivars (cv. P947, cv. KF429 and cv. SS405) of forage sorghum were evaluated at two locations (Suwon and Sunghwan) for 2 years (1999${\sim}$2000). 'KF429' was susceptible to foliar disease, while 'SS405' had less lodging resistance among the sorghum cultivars tested. When compared with 'P947' (recommended cultivar), dry matter yield of 'KF429' and 'SS405' cultivars increased by 16% and 75%, respectively. The crude protein of 'P947'(9.4%) was higher than other cultivars. The percentage of ADF and NDF were the lowest in 'KF429' cultivar. The results of forage performance experiment indicate that 'KF429' and 'SS405' are recommended as the government recommended sorghum cultivars due to a high lodging tolerance, disease resistance, and high dry matter yield.

• Journal of Advanced Navigation Technology
• /
• v.6 no.1
• /
• pp.17-26
• /
• 2002

In this paper, we have analyzed the BER (Bit Error Rate) performance of multi-user detectors employing SIC(Successive Interference Cancellation) and PIC (Parallel Interference Cancellation) which are the representative schemes in the subtractive interference cancellation. We have considered the MUD structure employing HIC (Hybrid Interference Cancellation) which combines SIC with PIC scheme, and then analyzed the BER performance. We have evaluated the BER performance of SIC and HIC schemes which execute the soft decision to generate the tentative data bit for the purpose of the interference cancellation in MAI and noise environments. Through the numerical analysis and computer simulation, it is shown that HIC can remove the effect of MAI more efficiently than the others, that improve the BER performance and increase the capacity of DS-CDMA systems regardless of the power control conditions. The reason is that the SIC scheme in front of HIC can solve the near-far problem caused by the imperfect power control and PIC scheme in the rear of it can improve the performance much more.

• The KIPS Transactions:PartA
• /
• v.18A no.4
• /
• pp.135-142
• /
• 2011

This research is to design an effective buffer structure and its management for flash memory based high performance SSDs (Solid State Disks). Specifically conventional SSDs tend to show asymmetrical performance in read and /write operations, in addition to a limited number of erase operations. To minimize the number of erase operations and write latency, the degree of interleaving levels over multiple flash memory chips should be maximized. Thus, to increase the interleaving effect, an effective buffer structure is proposed for the SSD with a hybrid address mapping scheme and super-block management. The proposed buffer operation is designed to provide performance improvement and enhanced flash memory life cycle. Also its management is based on a new selection scheme to determine random and sequential accesses, depending on execution characteristics, and a method to enhance the size of sequential access unit by aggressive merging. Experiments show that a newly developed mapping table under the MBA is more efficient than the basic simple management in terms of maintenance and performance. The overall performance is increased by around 35% in comparison with the basic simple management.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3A
• /
• pp.207-214
• /
• 2011

Ultra High Performance Concrete (UHPC), which is characterized by its high strength and advanced ductile behavior that is much superior to those of convention concrete, is a useful material to make thinner and longer bridges. The precast segmental construction method utilizing UHPC has been mainly studied because cast-in-place UHPC is very difficult and complicate to be achieved. As a part of those research, the structural performance evaluation of different types of joint connection method for hybrid cable-stayed bridge utilizing UHPC by using nonlinear analyses is performed in this study. The bond stress at joint is obtained by section force analyses for a 600 m cable-stayed bridge deck, and compared with the required bond stress at joint. Analysis results show that the U Type connection and straight type connection resist the highest ultimate load and bond strength, respectively. In addition, all considered joint connection systems satisfy the bond performances at joint required in the final stage of cable-stayed bridge utilizing UHPC.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.8
• /
• pp.623-628
• /
• 2013

The retrodirective array antenna system is operated faster than existing techniques of beamforming due to its less complexity. Therefore, it is effective for beam tracking in the environment of fast vehicle. On the other hand, it also has difficulty in estimating AOA according to multipath environment or multiuser signals. To improve the certainty of estimating AOA), this article proposes hybrid digital retrodirective array antenna systme combined with MUSIC algorithm. In this paper, the digital retrodirective array antenna system is designed according to the number of antenna array by using only one digital PLL which finds angle of delayed phase. And we evaluate the performance of the digital retrodirective array antenna for the high speed tracking application. Performance is studied by simulink when the speed of mobile is 300km/h and the distance between transmitter and receiver is 100m and then we have to confirm the performance of the system in multi path environment. As a result, the mean of AOA (Angle Of Arrival) error is $4.2^{\circ}$ when SNR is 10dB and it is $1.3^{\circ}$ when SNR is 20dB. Consequently, the digital RDA shows very good performance for high speed tracking due to the simple calculation and realization.

• Applied Biological Chemistry
• /
• v.18 no.4
• /
• pp.219-227
• /
• 1975

In order to investigate the possibility of wine-making with the grape variety cultivating in Korea, the basic analysises were carried out; analysis of the grape maturity during ripening period, the composition of grape juice, and the chemical components of wine from different varieties. Also the yeasts existing naturally on the grape were isolated and identified. For the selection of strain, the characteristics of 6 strains were studied. The results obtained were summarized as follows. 1. The reducing sugar content increased considerably during two weeks after the ordinary grape-gathering period. 2. The sugar content was highest in Muscat bailey A, which could be fermented naturally. The other varieties, Campbell Early, Steuben, and Alden needed chaptalisation for wine-making. 3. The permanaganate number and the methanol content of wine from all varieties were lower than french wine. 4. The sensory evaluation of wine showed that the pink wine was appreciated better than the red wine of same variety and the foxy taste of wine from hybrid grape influenced little to Korean. 5. The selected 6 strains were identified as Saccharomyces chevaliers, Saccharomyces capensis and Saccharomyces globosus. The strain No. 3 and No. 4 showed the most excellent characters for wine-making.