• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.4
• /
• pp.1111-1129
• /
• 2014

A 9300 TEU container carrier was equipped in 2006 with instrumentation aimed at wave induced accelerations, and motions. In 2010 the system was extended with strain sensors to include structural loads. Section loads for vertical bending could be readily obtained but the originally intended derivation of horizontal bending and torsion from the measured strains was found to be unreliable. This paper addresses an alternative approach that was adopted in the post processing of results. In particular the concept to use acceleration sensors to capture global hull deformations along the length of the hull, and the use of a data fusion procedure to obtain section loads from combined sensor data and finite element calculations. The approach is illustrated by comparison of actually measured accelerations and local strains with values obtained from the data fusion model. It is concluded that the approach is promising but in need of further validation and development. In particular the number and shapes of the modes used may not have been sufficient to represent the true deflection and thus strain distributions along the high loaded areas.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.7 no.1
• /
• pp.13-26
• /
• 1970

An elastic plate bar jointed to a rigid bar is considered. The bar is subjected to uniform axial tension. A theoretical approximate solution is obtained in an infinite hyperbolic series form and some numerical results for various Poisson's ratios are presented. A rubber plate joined to a strong wooden plate has been tested to obtain an experimental data and the results are compared with theoretical ones. Two values for vertical displacements are in good agreement but it is not satisfactory for horizontal displacements. The conclusion arrived at are as follow : The natures of stress distributions and deformed shapes given by above theoretical solution are compatible in mechanical sense. The magnitudes of stress and displacement components would not be reliable for exact works. A sharp shear stress concentrations are detected at the both ends of the joint.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1767-1771
• /
• 2004

A 4D-PTV system was constructed. The measurement system consists of three high-speed high-definition cameras, Nd-Yag laser(10mJ, 2000fps) and a host computer. The GA-3D-PTV algorithm was used to extract three-dimensional velocity vectors in the measurement volume. A horizontal impinged jet flow was measured with the constructed system. The Reynolds number is about 40,000. Spatial temporal evolution of the jet flow was examined in detail and physical properties such as spatial distributions of vorticity and turbulent kinetic energy were obtained with the constructed system.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.12
• /
• pp.1282-1287
• /
• 2001

This study presents the numerical analysis of natural convection of a micro- environments with air permeability in the clothing air-layer. As a numerical model the clothing air layer of shoulder and arm were adopted. Finite volume method for two-dimensional laminar flow was used for the analysis of flow and thermal characteristics of velocity, temperature and concentration in the air layer between body and clothing. As temperature boundary conditions, a body skin has a high temperature with $34^{\circ}C$ and the environmental temperatures are 5, 15 and $25^{\circ}C$ for various permeability coefficients. The distributions of concentration, temperature and velocity are shown that two large cells form at horizontal and vertical air layer, respectively. As the temperature difference between body skin and environment decreases, the heat transfer is decreased rapidly.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.1 no.2
• /
• pp.128-137
• /
• 1989

Numerical solutions for two-dimensional, steady, free convection are presented for a cylinder filled with saturated porous media. An annulus is bounded by inner wall with constant heat flux and two adiabatic horizontal walls with outer wall isothermally cooled. Governing equations are numerically solved for the range of Aspect Ratio 1 to 20, Radius Ratio, 1 to 20, and Rayleigh number, 50 to $10^4$ by Finite Difference method utilizing upwind scheme. Results are presented in terms of stream lines and isotherms, temperature distributions and local Nusselt numbers at the heated wall. Average Nusselt numbers are also presented for the comparisons.

• 한국가시화정보학회:학술대회논문집
• /
• 2006.12a
• /
• pp.102-108
• /
• 2006

The three-dimensional flows in the Weis-Fogh mechanism are studied by flow visualization and numerical simulation by the discrete vortex method. In this mechanism, two wings open, touching their trailing edges (fling), and rotate in opposite directions in the horizontal plane. The structure of the vortex systems shed from the wings is very complicated and their effects on the forces on the wings have not yet been clarified. The discrete vortex method, especially the vortex stick method, is employed to investigate the vortex structure in the wake of the two wings. The wings are represented by lattice vortices, and the shed vortices are expressed by discrete three-dimensional vortex sticks. The vortex distributions and the velocity field are calculated. The pressure is estimated by the Bernoulli equation, and the lift on the wing are also obtained.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.8
• /
• pp.2458-2467
• /
• 1996

The rigid-plastic finite element analysis was performed for analysis of ofhot forging and cold sizing of a bevel gear. Two dimensional analysis was carried out to investigate the defect occurrence on vertical symmetric planes during hot forging and three dimensional analysis was to understand the filling behavior on horizontal planes during cold sizing. The involute curve of a tooth was approximated by a circle for convenience in the present analysis. In order to estimate the elastic deformation of the gear and dies during cold sizing, linear elastic finite element analysis was performed. Results of the analysis can be used to predict grain flows and strength distributions in the forged gear, and to design dies and an appropriate preform for the cold sizing.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.15 no.4
• /
• pp.388-395
• /
• 1986

Numerical solutions of two-dimensional, steady, and natural are investigated in a confined rectangular cavity with porous media. The saturated fluid is bounded by two isothermal vertical walls at different temperatures and two adiabatic horizontal walls. Governing equations are numerically solved by finite difference method with the up wind scheme. Distributions of streamline and temperature we. predicted for aspect ratios ranging from 0.1 to 1.0, Rayleigh numbers 50 to $10^4$, and tilt angles $0^{\circ}\;to\;60^{\circ}$. Representative plots of temperature and velocity field according to tilt angle are presented. The effects of aspect ratio, Rayleigh number, and tilt angle on local and average Nusselt numbers are obtained. The optimum conditions for maximum Nusselt number are also presented with tilt angles.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.1
• /
• pp.9-16
• /
• 1996

In order to understand microbial ecosystem in the fast china sea and Yosu coastal sea horizontal distributions of bacterial flora, Vibrio spp., coliform group, temperature, and salinity in this sea area, were studied 42 sampling stations during 6th-l4th August, 1992. From the results, salinity and temperature were $24.64\~33.78\%_{\circ}$ and $22.53\~29.18^{\circ}C$, respectively. As the open sea far from land goes on, salinity became low while temperature became high. Viable cell counts of bacteral flova, Vibrio spp., and roliform group in Yosu coastal sea water were $1.0\times10^2\~3.0\times10^4/ml,\;0.2\times10\~9.0\times10^3/ml,\;and\;0.3\times10\~3.0\times10^3/ml$ while those of these in the open sea water were $0.4\times10\~2.0\times10^3/ml,\;0.8\times10\~3.0\times10/ml,\;and\;0.9\times10\~1.3\times10/ml$, respectively.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.1
• /
• pp.17-25
• /
• 1996

The results identified for bacterial flora 174, Vibrio spp.132, and coliform group 183 strains isolated from the areas of last China Sea and Yosu coastal sea during from August 6th. to 14th. 1992 were as follow: 40 strains among the 74 strains of bacteria flora isolated from fast China sea area were Pseudomonas spp.$(54\%)$ and 60 strains among the 100 strains isolated from Yosu sea area were Enterobacteriaceae $(60\%)$. Four strains were Vibrio alginoliticus and one strain of V, parahaemolyticus among 5 strains of genus Vibrio isolated from last China Sea. While 54 strains were V. alginolyticus $(43\%)$ and V, parahaemolyticus $(17\%)$ among 127 strains genus Vibrio isolated from Yosu coastal sea area. Seventy nine strains among the 156 strains of coliform group isolated from Vosu sea area were Escherichia coli I $(51\%)$ and each one strain Citrobacter freundii I and II. 3 strains among 27 strains isolated from last China sea area were E. coli$(11\%)$ and 1 strain of C. freundii I. Coliform group was grouped into 16 types by IMViC system, $44^{\circ}C$, gelatin liquefaction test.