• 한국분무공학회지
• /
• 제15권2호
• /
• pp.61-66
• /
• 2010

Fuel spray characteristics of the gasoline engine injector has been studied experimentally. To provide fundamental performance data of 4-hole and 12-hole injectors, spray fuel-mass distribution, wall wetting fuel amount and visualization of injectors have been tested and measured with various fuel supply pressure conditions. Spray visualization has been performed to analyze spray formation, spray angle, stream width and penetration length. Test result shows that wall wetting is greatly influenced by the induction air amount and spray atomization. Spray visualization shows that the 12-hole injector has robust performance characteristics with various fuel supply pressure conditions compared with the 4-hole injector. 4-hole injector generates relatively less wall-wetting fuel amount than 12-hole injector does.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.13-14
• /
• 2005

Multi-dimensional combustion analysis and experiment has been carried out to investigate the effects of the injector nozzle hole diameter and number on the NOx formation and fuel consumption in HYUNDAI HiMSEN engine. The behavior of spray and combustion phenomena in diesel engine was examined by FIRE code. Wave breakup and Zeldovich models were adopted to describe the atomization characteristics and NOx formation. Wallfilm model suggested by Mundo, et al. and auto-ignition model suggested by Theobald and Cheng were adopted to investigate the spray-wall interaction characteristics and ignition delay. The information of spray angle and spray tip penetration length was extracted from fuel spray visualization experiment and the fuel injection rate profile was extracted from fuel injection system experiment as an input and verification data for the combustion analysis. Next, the nine different nozzle configurations were simulated to evaluate the effect of injector hole diameter and number on the NOx formation and fuel consumption.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.183-192
• /
• 2014

In this work, the mixture formation and atomization characteristics of biodiesel fuel were reviewed under various test conditions for the optimization of compression-ignition engine fueled with biodiesel. To achieve these, the effect of nozzle caviting flow, group-hole nozzle geometry and injection strategies on the injection rate, spray evolution and atomization characteristics of biodiesel were studied by using spray characteristics measuring system. At the same time, the fuel heating system was installed to obtain the effect of fuel temperature on the biodiesel fuel atomization. It was revealed that cavitation in the nozzle orifice promoted the atomization performance of biodiesel. The group-hole nozzle geometry and split injection strategies couldn't improve it, however, the different orifice angles which were diverged and converged angle of a group-hole nozzle enhanced the biodiesel atomization. It was also observed that the increase of fuel temperature induced the quick evaporation of biodiesel fuel droplet.

• 지질공학
• /
• 제13권3호
• /
• pp.281-292
• /
• 2003

모형시추공 내에서 공내수 전기전도도의 자동 측정시스템을 구축하고 이로부터 수리상수 결정과 관련된 제반 기초 환경을 검증하였다. 실험은 상대적으로 높은 염도를 공내수로 하고 증류수를 지층수로 사용하여 지층수의 유입과 유출되는 유량을 일정하게 유지한 상태에서 공내수의 전기전도도 프로파일을 구하는 방식으로 이루어졌다. 관찰의 주 대상은 공내수와 지층수 사이의 염도차. 온도차 및 지층수의 유입량. 유입 ·유출구에 따른 모형시추공 내에서의 전기전도도 변화 양상 파악에 있었다. 실헌결과, 이들 요인이 미치는 영향범위와 적정 측정 환경이 제시되어 향후 모델 실험 및 원위치시험에서 적용될 기초실험 여건이 마련되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 추계학술대회 논문집 학회본부
• /
• pp.164-167
• /
• 1988

This paper reports optical properties and hole formation of a 488nm-optimumed trilayer structure utiluzed Te-based thin films as a recording layer, and the application of trilayer to 830nm. The optical recording characteristics of metallic recording media are enhanced significantly by incoporating the metal (Al) layer into an antireflection trilayer structure. Due to the interference condition inherent in the design of the trilayer structure, reflectance from holes is ranked a low fraction. the hole formation is carried out by laser by $Ar^+$ laser(488nm). For 20nsec laser pulse duration, the hole opening threshold power of $(Te_{86}Se_{14})_{50}Bi_{50}$ trilayer is lower than that of monolayor that used in this experiments. Hole shapes of the whole sample were clean. For the application of the diode laser, the thickness of dielectric is varied by$\lambda$/4n. In order to compare the monolayer with the trilayer reflectance was measured.

• 한국레이저가공학회지
• /
• 제12권1호
• /
• pp.14-18
• /
• 2009

Ripple formation of femtosecond laser in stainless steel is investigated using 184 fs pulses with a center wavelength of 785 nm. The effect of the laser polarization relative to the translation direction is observed. For drilling with a certain aspect ratio, reflections at the hole walls take place, leading to a non-uniform intensity distribution deep inside the formed hole. Finally, it is shown that a circular polarization during the drilling process significantly improves the quality of the produced holes.

• Applied Microscopy
• /
• 제45권3호
• /
• pp.107-114
• /
• 2015

Two-dimensional (2D) materials containing hole defects are a promising substitute for conventional nanopore membranes like silicon nitride. Hole defects on 2D materials, as atomically thin nanopores, have been used in nanopore devices, such as DNA sensor, gas sensor and purifier at lab-scale. For practical applications of 2D materials to nanopore devices, researches on characteristics of hole defects on graphene, hexagonal boron nitride and molybdenum disulfide have been conducted precisely using transmission electron microscope. Here, we summarized formation, features, structural preference and stability of hole defects on 2D materials with atomic-resolution transmission electron microscope images and theoretical calculations, emphasizing the future challenges in controlling the edge structures and stabilization of hole defects. Exploring the properties at the local structure of hole defects through in situ experiments is also the important issue for the fabrication of realistic 2D nanopore devices.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.297-298
• /
• 2009

대부분의 반도체 소자의 고장 원인은 85%정도가 열로 인한 것이며, 고출력 LED는 인가된 에너지의 20%정도의 광으로 출력되며 나머지 80%가 열로 전환된다. 본 논문에서는 PMS-50과 KEITHLEY 2430을 이용하여 PCB 구조와 Via hole 구성에 따른 LED 패키지의 열적 광학적 특성을 분석하였다. 0.6mm의 Via hole을 가진 FR4 PCB의 열특성이 가장 우수하였으며, Via hole 0.6mm FR4 PCB의 경우 McPCB에 상응하는 광출력 특성을 보였다.

• 천문학논총
• /
• 제25권3호
• /
• pp.77-82
• /
• 2010

Recent results from large surveys of the local universe show that the galaxy-black hole connection is linked to host morphology at a fundamental level and that there are two fundamentally different modes of black hole growth. The fraction of early-type galaxies with actively growing black holes, and therefore the AGN duty cycle, declines significantly with increasing black hole mass. Late-type galaxies exhibit the opposite trend: the fraction of actively growing black holes increases with black hole mass. Issues of AGN selection bias and prospects for near-future efforts with high redshift data are discussed.

• Applied Microscopy
• /
• 제50권
• /
• pp.27.1-27.6
• /
• 2020

Transition metal dichalcogenides (TMD), which is composed of a transition metal atom and chalcogen ion atoms, usually form vacancies based on the knock-on threshold of each atom. In particular, when electron beam is irradiated on a monolayer TMD such as MoS₂ and WS₂, S vacancies are formed preferentially, and they are aligned linearly to constitute line defects. And then, a hole is formed at the point where the successively formed line defects collide, and metal clusters are also formed at the edge of the hole. This study reports a process in which the line defects formed in a monolayer WS₂ sheet expends into holes. Here, the process in which the W cluster, which always occurs at the edge of the formed hole, goes through a uniform intermediate phase is explained based on the line defects and the formation behavior of the hole. Further investigation confirms the atomic structure of the intermediate phase using annular dark field scanning transition electron microscopy (ADF-STEM) and image simulation.