• Journal of Information Technology Services
• /
• v.9 no.2
• /
• pp.151-161
• /
• 2010

Recently, as the era of ubiquitous has arrived, an infrastructure for the short-distance wireless communication has been extended socially, and thus a variety of services are being proposed. The Multimedia Contents Delivery System using the ZigBee, in particular, has an important stance in enlargement of a variety of services in the aspect of individual-oriented service support though Wireless Personal Area Network (WPAN). Nonetheless, the ZigBee, or the IEEE 802.15.4 Standard, has many restrictions on the Multimedia Contents Delivery System due to the low data transport rate. In order to improve the ZigBee which presents a limit on the transport rate at the IEEE 802.15.4 Standard, this thesis has designed the burst mode which is a method of transmitting a certain amount of data in block units at a high speed without any stoppage until the completion of the transmission. Also, to provide a Multimedia Contents Delivery Service with an application of the normal data transmission mode, it improved the transmission performance of the ZigBee. In addition, for the Multimedia Contents Delivery Service under the ubiquitous environment, it designed and implemented a broadcasting Multimedia Contents Delivery System based on the ZigBee to conduct a comparative analysis on the data transmission performance according to the transmission method.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.5
• /
• pp.455-461
• /
• 2017

In this paper, a local DL (Data Line) sensing method with smaller parasitic capacitance replacing the previous distributed DB sensing method with large parasitic capacitance is proposed to reduce the time to transfer BL (Bit Line) voltage to DL in the read mode. A new BL switching circuit turning on NMOS switches faster is also proposed. Furthermore, the access time is reduced to 35.63ns from 40ns in the read mode and thus meets the requirement since BL node voltage is clamped at 0.6V by a DL clamping circuit instead of precharging the node to VDD-VT and a differential amplifier are used. The layout size of the designed 512Kb EEPROM memory IP based on a $0.13{\mu}m$ BCD is $923.4{\mu}m{\times}1150.96{\mu}m$ ($=1.063mm^2$).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.4A
• /
• pp.219-226
• /
• 2012

We investigated the performance of a visible light communication (VLC) transceiver applicable to both of illumination and wireless communication. we considered the visibility of VLC, the easy connection for wireless communication and high-speed transmission and implemented VLC transceiver based on edge-emitting laser diode and silicon photodiode. The proposed VLC transceiver is designated to operate in a full duplex mode at high speed of 120 Mbit/s. The shielding method that is employed as a means to reduce the light cross coupling effect inside the VLC transceiver is proposed and its performance is experimentally measured. We also applied optical antenna to have the larger angle of field of view (FOV) to novel structure of VLC transceiver and examined and analyzed their bit error rate performance, photometric result with respect to the transmission distance, the coverage range and the tilt degree as transmission link characteristic between two transceivers without optical antenna and with optical antenna.

• Journal of IKEEE
• /
• v.4 no.2 s.7
• /
• pp.274-280
• /
• 2000

The fact that error probability is higher in wireless communication environment than the one in a fixed network makes it inappropriate to apply the same DLC (Data Link Control) protocol used in a wireline network to a wireless network. And since the existing DLC protocol for wireless network was optimized for low-rate data service, it is not suitable for a wireless network environment which should support high-speed and multimedia traffic. Therefore it is desperate to have a new DLC protocol for todays wireless mobile communication environment. In this paper, we propose an error control scheme in WATM (Wireless Asynchronous Transfer Mode) environment. which supportsmultiple traffic attributes, high-speed, multimedia data service. In this paper we modified the existing ASR ARQ (Adaptive Selective Repeat Automatic Repeat Request) protocol where cells exceeding maximum allowable delay range are discarded. And adding FEC (Forward Error Correction) for delay-sensitive traffic resulted in smaller increase of transmission delay.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.5
• /
• pp.276-283
• /
• 2018

The purpose of the study is to identify a sound generating organ that has a major influence on the central frequency of the cicadas with the Helmholtz resonator structure for the first time. The sound of cicadas Cryptotympana atrata and Hyalessa fuscata were recorded and analyzed, then the motion of the tymbals was analyzed with a high-speed camera to compare the relationship between the frequency of sound and the motion of the tymbals. As a result, there was little difference in the frequency distribution of calling song and scream for two species. The tymbals of C. atrata oscillated in three vibration modes, while those of H. fuscata oscillated in one mode. There was no difference in the frequency of both tymbals of both cicadas, and three vibration modes of C. atrata generated sound with different frequency bands. The frequency band of tymbals and the central frequency band of calling song were very similar. In conclusion, it is presumed that the frequency of the cicadas with the Helmholtz resonator structure was determined by mode frequency of the tymbals than resonance condition of the abdomen.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.357-360
• /
• 2013

A 1.8V 2-Gb/s scalable low voltage signaling (SLVS) transmitter (TX) is designed for mobile applications requiring high speed and low power consumption. It consists of 4-lane TX for data transmission, 1-lane TX for a source synchronous clocking, and a 8-phase clock generator. The proposed SLVS TX has the scaling voltage swing from 50 mV to 650 mV and supports a high speed (HS) mode and a low power (LP) mode. An output impedance calibration scheme for the SVLS TX is proposed to improve the signal integrity. The proposed SLVS TX is implemented by using a $0.18-{\mu}m$ 1-poly 6-metal CMOS with a 1.8V supply. The simulated data jitter of the implemented SLVS TX is about 8.04 ps at the data rate of 2-Gbps. The area and power consumption of the 1-lane of the proposed SLVS TX are $422{\times}474{\mu}m^2$ and 5.35 mW/Gb/s, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.9
• /
• pp.1051-1061
• /
• 2011

The influences of density variation on stress and displacement fields at a propagating Mode-III crack tip in orthotropic functionally graded materials (OFGMs) are studied. The crack propagates dynamically at a right angle to the gradient of physical properties. Three kinds of elasticity and density gradients are analyzed in this study. They are as follows: (1) the density varies without elasticity variation, (2) the directions of the density and elasticity gradients are opposite to each other, and (3) same. For these cases, the stress and displacement fields at the crack tip are developed and the dynamic stress intensity factors for propagating cracks are also studied. When the crack speed is low, the influence of density variation on the stresses and displacement is low. However, when the crack speed is high, this influence is very high.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.17 no.1
• /
• pp.25-29
• /
• 1980

For the preliminary estimation of the vertical hull natural frequency, the Schlick's or Schlick-type formulae have been traditional ones and are still in common use today. Some investigators have made their efforts, based on statistical data of ships' system parameters, to extend the applicability of Schlick-type formulae to higher modes, or to utilize the Rayleigh method. For instance, the work done by Dinsenbacher et al.[5] belongs to the former and that of Nagamoto et al.[6] to the latter. In a part of his previous paper[7], the author, investigating the case of a cargo ship of medium size, suggested that provided statistically simplified curves such as trapezoid of system parameter distributions are available in hands, direct utlization of an ordinary computer program can be also an another convenient method by which we can obtain both natural frequencies and normal mode shapes. In this paper, to confirm the feasibility of the above suggestion, four high speed boats are investigated. The system parameters of them are originally given in [5]. The computer program used here is one confiled based on a calculation method derived from Myklestal-Prohl modeling of hull, transfer matrix formulation and an extended Gumbel's initial value method for solving frequency equation. The results of the investigation show that the direct calculation based on statistically oriented and reasonably assumed trapezoidal mean curves of system parameter distributions can give us natural frequencies within about 5% deviation up to several-noded modes and normal mode shapes serviceable at least up to 4- or 5-noded modes in comparision with those based on actual distributions of system parameters. For this simplified method the actual data required for input are only of ship length, displacement, total added mass, bending and shear rigidity at amidship. They are available at the early stage of design. By this method we can also easily trace variations of vibration characteristics in the course of ship design cycles.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1A
• /
• pp.95-104
• /
• 2008

Dynamic behaviors of the two-span continuous bridge which is one of prototypes on Gyoung-Bu high-speed railway are analyzed and some methods for reducing the resonance of the bridge are proposed. The bridge is modeled as a two-span continuous beam and the load is a vehicle of TGV-K (2p+18T) with length of 380.15 meter traveling on the railway bridge at some constant velocity. The equations governing the dynamic behaviors of the bridge are partial differential equations produced by using a system with distributed mass and elasticity. The analysis of the governing equations is performed by the mode superposition method which has modal coordinates solved by Duhamel's integral. Without considering the train velocity the dynamic reponses can be greatly reduced at some special lengths of bridge. It is different from the results of simple bridges researched so far. When the dynamic responses increase rapidly to make a resonance phenomenon depending on the train velocities, the several methods are proposed to deduce the resonance.

• Journal of ILASS-Korea
• /
• v.25 no.1
• /
• pp.27-33
• /
• 2020

NOx, PN and CO emissions from diesel trucks make up a significant portion of domestic air pollutant emissions. Therefore, test vehicles with various emission standards and driving modes were selected to evaluate the emission characteristics of regulated pollutants (NOx, PN, CO) in medium-duty trucks. As a result of test, all test vehicles were satisfied with Euro 5 or 6 regulation. NOx emissions of Euro 6 vehicles with after-treatment of LNT + DPF were lower than those of Euro 5 vehicles with DPF. In WLTC mode, all vehicles have high NOx emissions at section of extra high speeds, which are determined by increased fuel consumption and high combustion temperatures. CO and PN emissions from all vehicles were found to be low at section of low speeds. Also, The NO₂/NOx ratio was analyzed at 7-23% in each mode, and the NO₂/NOx ratio increased as the average vehicle speed increased. In NIER 9 mode, the CO, HC, and PN emissions were higher under cold conditions of engine than hot conditions of engine. In addition, vehicles with after-treatment system of LNT have similar NOx emissions level in this study.