• Journal of the Korea Institute of Building Construction
• /
• v.14 no.1
• /
• pp.110-117
• /
• 2014

The objective of this study is to investigate an effect of curing temperature on autogenous shrinkage of high strength cement mortar with 0.15 of W/B incorporating fly ash and silica fume in terms of equivalent age. The contents of fly ash and silica fume are varied from 10% to 30%. Non linear regression model applying equivalent age was used to estimate the autogenous shrinkage evolution. To obtain apparent activation energy($E_a$), setting time method by Pinto and existing method were calculated and compared respectively. Test results showed that use of silica fume increased autogenous shrinkage while use of fly ash decreased it. It was also found that poor agreements were obtained when $E_a$ by setting time was applied. But, application of existing $E_a$ resulted in a good agreement between calculated autogenous shrinkage and measured one.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.131-131
• /
• 2003

The advent of photonic technologies in the field of communications and data transmission has been heavily increasing the demand in integrated optical (IO) circuits capable of accomplishing not only simple tasks like signal, but also more sophisticated functions like all-optical signal routing or active multiplexing/demultiplexing. In the last decade, sol-gel technology has been widely used to prepare optical materials. Sol-gel processes show many promises for the development of low-loss, high-performance glass integrated optical circuits. However, crack formation is likely to occur during heat treatment in thick gel films. In order to overcome the critical thickness limitation, the organic-modified silicate has been widely used. In this case coating matrices have been prepared from the organo-silanes of T structures, acidic catalyst and the as-prepared gel films have been heat-treated below 200$^{\circ}C$ to avoid the crack formation and the degradation of organic components. However, the films prepared in the acidic condition and the low heat temperature make the films contain high OH groups which is the major optical loss function. In this work, C$\sub$6/H$\sub$5/SiO$\sub$1.5/ films were prepared on silicon substrate by sol-gel method using base catalyst in a PTMS/NH$_4$OH/H$_2$O/C$_2$H$\sub$5/OH system. The sol showed spinable viscosity at 50 wt% of solid content, and neglectable viscosity change with time. The films were crack-free and transparent after curing at 450 $^{\circ}C$, and highly condensed to minimize OH content in C$\sub$6/H$\sub$5/SiO$\sub$1.5/ networks. The effects of heat treatment of the films are characterized on the critical thickness, the chemical composition and the refractive indices by means of SEM, FT-IR, TGA, prism coupler, respectively.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.6
• /
• pp.661-666
• /
• 2006

The compressive strength of a paste composed of a low-calcium Class F fly ash and alkaline activator solutions was investigated. These activator solutions, made with sodium hydroxide, water glass and water, have a very high $OH^-$ concentration. The composition of alkaline activator solution and temperature have been shown to notably influence the development of the compressive strength of the fly ash-cements paste. Compressive strength of 50 MPa could be achieved by curing of the fly ash at $60^{\circ}C$ for 48 hrs or $85^{\circ}C$ for 24 hrs. This study presented the optimum mixing ratio of Class F fly ash/sodium hydroxide/water glass as 25:8:2 in weight basis, and activator/fly ash as 0.6/1.0 for high strength paste.

• Polymer(Korea)
• /
• v.27 no.2
• /
• pp.120-128
• /
• 2003

The effects of catalyst, accelerator and blend composition on the cure behavior of unsaturated polyester resin (UPE), vinyl ester resin (VE) and their blends were studied using differential scanning calorimetry(DSC). The DSC thermograms strongly depend on each variable. The result shows that the small exothermic peak at 115$^{\circ}C$ is due mainly to the UPE component in the UPE/VE blends and the large one at 134~138 $^{\circ}C$ is due mainly to the VE component. The results also indicate that the change of the DSC thermogram measured after each blend was exposed to high temperature 18$0^{\circ}C$ and the fast curing conditions of a few tens seconds provide useful information on understanding the thermal processing of a blend at high speed. The measurements of resin flow time represent that there are three distinct stages of cure in the UPE/VE blends: induction, transition and macro-gelation stages, as similarly reported for UPE by others earlier. The thermal stability and flexural properties of the cured UPE are significantly improved by blending it with the VE, depending on the composition.

• Elastomers and Composites
• /
• v.47 no.3
• /
• pp.231-237
• /
• 2012

This study measured the mechanical and damping properties of EPDM compounds including fillers. Semi-reinforcing furnace black (SRF), high abrasion furnace black (HAF) and acetylene black were used as fillers. Dicumyl peroxide (DCP) were used as curing agents. The measurements were conducted using a moving die rheometer (MDR), durometer, universal testing machine (UTM), compression set and dynamic mechanical analysis (DMA). The tensile strength and elongation at break increased with increasing SRF contents in EPDM compounds. However, they decreased with increasing the amount of acetylene black. In the inspecting temperature range, EPDM compound filled acetylene black had stable storage modulus. Furthermore, the tan ${\delta}$ of the EPDM compounds obtained was enhanced by compounding with acetylene black.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.549-555
• /
• 2012

Silicon carbide(SiC) exhibits many unique properties, such as high strength, corrosion resistance, and high temperature stability. In this study, a SiC-fiber web was prepared from polycarbosilane(PCS) solution by employing the electrospinning process. Then, the SiC-fiber web was pyrolyzed at $1800^{\circ}C$ in argon atmosphere after it was subjected to a thermal curing. The SiC-fiber web (ground web)/phenolic resin (resol) composite was fabricated by hot pressing after mixing the SiC-fiber web and the phenolic resin. The SiC-fiber web composition was controlled by changing the fraction of filler (filler/binder = 9:1, 8:2, 7:3, 6:4, 5:5). Thermal conductivity measurement indicates that at the filler content of 60%, the thermal conductivity was highest, at 6.6 W/mK, due to the resulting structure formed by the filler and binder being closed-packed. Finally, the microstructure of the composites of SiC-fiber web/resin was investigated by FE-SEM, EDS, and XRD.

• Polymer(Korea)
• /
• v.28 no.4
• /
• pp.298-304
• /
• 2004

We fabricated a polymer dispersed liquid crystal (PDLC) cell using LC with negative dielectric anisotropy and UV curable monomer exhibiting transparent state initially (called normally transparent (NT)) and studied the electro-optic characteristics. The NT PDLC cell made with the ratio of LC : monomer = 70/30 wt%, curing temperature of 20 $^{\circ}C$ and strong UV intensity of 198 ㎽/$\textrm{cm}^2$ had high contrast ratio and showed good electro-optic characteristics. In this condition, LC is aligned vertically on the substrate due to the vertical alignment layer and the polymer made with the UV exposure does not influence the alignment of the LC much. Therefore, the transmittance at the zero voltage is very high and the scattering state of the cell is good after applying the voltage because LC with negative dielectric anisotropy tries to align perpendicular to the field. And also, the NT PDLC cell showed better viewing angle characteristics than that in the normally scattering (NS) PDLC.

• Journal of the Korea Convergence Society
• /
• v.12 no.2
• /
• pp.185-191
• /
• 2021

The characteristics of the foundry sand were analyzed for water jacket core required to prevent structural deformation from the heat generated in the cylinder bore during the casting of the cylinder block of an automobile. The sand core tensile strength tester, AFS-GFN, and optical microscope were used to evaluate the its properties. If the SiO2 content is high in the foundry sand, the dimensional defects and veining defects occur due to high temperature expansion. Also, if it is too low, the core breakage, porosities, chemical burn-on defects occur. The particle size index and grain shape influenced the core strength and resin consumption, resulting in fluctuations in defect types. The higher the alkalinity of the dried sand, the lower the core strength. And the more basic, the lower the core strength. At the resin content of 1.6~1.8%, the increase in core strength after 1 hour curing was approximately at its maximum.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.2
• /
• pp.476-487
• /
• 2021

To prepare acrylic resin coatings containing 70% of solids, we used n-butyl methacrylate(BMA), methyl methacrylate(MMA), 2-hydroxyethyl methacrylate(2-HEMA), and acetoacetoxyethyl acrylate(AAEA), caprolactone acrylate(CLA) as raw materials, the glass transition temperature(T_g) of acrylic copolymer was adjusted around 50 ℃. The viscosity and molecular weight of the acrylic resins was increased with increasing OH values. Di-tert-amyl peroxide was found to be the suitable initiator to get high-solids acrylic resins. The optimum reaction conditions found in the study are 5 wt% of initiator, 4 wt% of chain transfer agent, 4 hrs of dropping time, and 140 ℃ of reaction temperature. The structure of the synthesized resins were characterized by FT-IR and ¹H-NMR spectroscopy. Number average molecular weight of 1900~2600 and molecular wight distribution of 1.4~2.1 were obtained. Crosslinked acrylic urethane clear coatings were obtained by curing reaction between the synthesized acrylic resins and hexamethylene diisocyanate trimer(Desmodur N-3300), the equivalent ratio of NCO/OH was 1.2/1.0. The physical properties from the following studies were carried out: viscosity(Zahn cup #2), adhesion, drying time, pot-life, pensil hardness, and 60° specular gloss. Various properties of the acrylic urethane clear coatings were also evaluated on the coating specimens. Adhesion property to a substrate, drying time, pot-life, pencil hardness, and 60° specular gloss of prepared paint showed quite good properties. Futhermore, prepared paint containing 10% of CLA showed quite good properties for adhesion, low viscosity and high hardness.

• Resources Recycling
• /
• v.19 no.6
• /
• pp.36-42
• /
• 2010

Researches on resources recycling in the field of construction have made an extensive progress such as recycled aggregate of waste concrete and recycling of asphalt. On the other hand, there are almost never researches on pavement method with used waste frying oil. In South Korea, 0.2 million ton used waste frying oil is discharged every year. It is guessed that about 0.1 million ton used waste frying oil can be collected. If used waste frying oil is recycled, it is expected that disuse cost will be reduced and water pollution of rivers will be prevented. Therefore, the purpose of the study was to evaluate on mechanical features (strength, water resistance, chemical resistance, abrasion resistance, freezing and thawing resistance and permeable coefficient) whether dense graded permeable concrete mixing silica sand with flexible alkyd resin manufactured by making ester reaction with collected used waste frying oil to make alkyd resin could be applied to road pavement for non-roadway. The results of the study were as follows. In flexural strength, it had 1.6 times as much as road design standard 4.5MPa. In water resistance, chemistry resistance and freezing and thawing resistance, they had lack of strength in early age. As age went by, they didn't have large changes. And curing temperature had phenomenon of increase in strength at rather low temperature than high temperature by glass transition temperature of resin. Therefore, considering workability, strength and durability when it was applied to road pavement, it was reasonable that the mixing ratio of flexible alkyd resin was 10~15% in comparison with silica sand weight.