• 한국전기전자재료학회논문지
• /
• 제33권4호
• /
• pp.291-296
• /
• 2020

The high power of a shingled photovoltaic module can be attributed to its low cell-to-module loss. The production of high power modules in limited area requires high efficiency solar cells. Shingled photovoltaic modules can be made by divided solar cells, which can be produced by the laser scribing process. After dividing the 21% PERC cell using laser scribing, the efficiency decreased by approximately 0.35%. However, there was no change in the efficiency of the solar cell having relatively lower efficiency, because the laser scribing process induce higher heat damages in solar cells with high efficiency. To prove this phenomena, the J₀ (leakage current density) of each cell was analyzed. It was found that the J₀ of 21% PERC increased about 17 times between full and divided solar cell. However, the J₀ of 20.2% PERC increased only about 2.5 times between full and divided solar cell.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.13-16
• /
• 2008

Solid oxide fuel cell(SOFC) is an electrochemical energy conversion system with high efficiency and low-emission of pollution. In order to reduce the operating temperature of SOFC system under $800^{\circ}C$, the thickness reduction of YSZ electrolyte to be as thin as possible, e.g., less than 10 ${\mu}m$ are considered with the microstructure control and optimum design of unit cell. Methods for reducing the thickness of YSZ electrolyte have been investigated in coin cell. Moreover, a large unit cell($8cm{\times}8cm$) for SOFC was fabricated using an anode-supported electrolyte assembly with a thinner electrolyte layer, which was prepared by a tape casting method with a co-sintering technique. we studied the design factors such as active layer, electrolyte thickness, cathode composition, etc,. by the coin type of unit cell ahead of the fabrication process of a large unit cell and also reviewed about the evaluation technique of a large size unit cell such as interconnect design, sealing materials and current collector and so forth. Electrochemical evaluations of the unit cells, including measurements such as power density and impedance, were performed and analyzed. Maximum power density and polarization impedance of coin cell were 0.34W/$cm^2$ and $0.45{\Omega}cm^2$ at $800^{\circ}C$, respectively. However, Maxium power density of a large unit cell($5cm{\times}5cm$) decreased to 0.21W/$cm^2$ at $800^{\circ}C$ due to the increase of ohmic resistance. However, It was found that the potential value of a large unit cell loaded by 0.22A/$cm^2$ showed 0.76V at 100hrs without the degradation of unit cell.

• 한국컴퓨터산업학회논문지
• /
• 제6권5호
• /
• pp.757-766
• /
• 2005

There have been great demands for higher density SRAM in all area of SRAM applications, such as mobile, network, cache, and embedded applications. Therefore, aggressive shrinkage of 6T Full CMOS SRAM had been continued as the technology advances, However, conventional 6T Full CMOS SRAM has a basic limitation in the cell size because it needs 6 transistors on a silicon substrate compared to 1 transistor in a DRAM cell. The typical cell area of 6T Full CMOS SRAM is $70{\sim}90F^{2}$, which is too large compared to $8{\sim}9F^{2}$ of DRAM cell. With 80nm design rule using 193nm ArF lithography, the maximum density is 72M bits at the most. Therefore, pseudo SRAM or 1T SRAM, whose memory cell is the same as DRAM cell, is being adopted for the solution of the high density SRAM applications more than 64M bits. However, the refresh time limits not only the maximum operation temperature but also nearly all critical electrical characteristics of the products such as stand_by current and random access time. In order to overcome both the size penalty of the conventional 6T Full CMOS SRAM cell and the poor characteristics of the TFT load cell, we have developed $S^{3}$ cell. The Load pMOS and the Pass nMOS on ILD have nearly single crystal silicon channel according to the TEM and electron diffraction pattern analysis. In this study, we present $S^{3}$ SRAM cell technology with 100nm design rule in further detail, including the process integration and the basic characteristics of stacked single crystal silicon TFT.

• 한국전기전자재료학회논문지
• /
• 제19권4호
• /
• pp.314-321
• /
• 2006

There have been great demands for higher density SRAM in all area of SRAM applications, such as mobile, network, cache, and embedded applications. Therefore, aggressive shrinkage of 6 T Full CMOS SRAM had been continued as the technology advances. However, conventional 6 T Full CMOS SRAM has a basic limitation in the cell size because it needs 6 transistors on a silicon substrate compared to 1 transistor in a DRAM cell. The typical cell area of 6 T Full CMOS SRAM is $70{\sim}90\;F^2$, which is too large compared to $8{\sim}9\;F^2$ of DRAM cell. With 80 nm design rule using 193 nm ArF lithography, the maximum density is 72 Mbits at the most. Therefore, pseudo SRAM or 1 T SRAM, whose memory cell is the same as DRAM cell, is being adopted for the solution of the high density SRAM applications more than 64 M bits. However, the refresh time limits not only the maximum operation temperature but also nearly all critical electrical characteristics of the products such as stand_by current and random access time. In order to overcome both the size penalty of the conventional 6 T Full CMOS SRAM cell and the poor characteristics of the TFT load cell, we have developed S3 cell. The Load pMOS and the Pass nMOS on ILD have nearly single crystal silicon channel according to the TEM and electron diffraction pattern analysis. In this study, we present $S^3$ SRAM cell technology with 100 nm design rule in further detail, including the process integration and the basic characteristics of stacked single crystal silicon TFT.

• 한국미생물·생명공학회지
• /
• 제45권2호
• /
• pp.149-154
• /
• 2017

본 연구에서는 Bacillus 유래 esterase를 생산할 수 있는 재조합 대장균을 사용하여 유가식 배양을 이용한 고농도 균체 배양을 통해 esterase 생산성을 극대화하고자 하였다. 유가식 배양 중 순수 산소의 공급을 통해 용존산소를 30% 이상 유지한 경우와 포도당농도를 1 g/l 이상 유지한 경우 각각 $OD_{600}$ 76 (35.8 g/l DCW)과 $OD_{600}$ 90 (42.4 g/l DCW)까지 균체량을 증가시킬 수 있었다. 포도당의 공급에도 불구하고 배양 후반에 세포의 성장이 정체되는 현상을 극복하기 위해 yeast extract가 강화된 추가 배지의 공급을 시도하였으며, 그 결과 $OD_{600}$ 185 (87.3 g/l DCW)까지 고농도 균체 배양이 가능함을 확인하였다. 단백질 생산 수율의 향상을 위해 성장 시기에 따라 induction에 의한 세포 성장과 esterase 생산성을 평가하였고, 그 결과 대수 성장기 후반에 induction을 유도한 경우 세포 성장 측면에서는 최대 $OD_{600}$ 190(89 g/l DCW)까지 고농도 균체 배양이 가능함을 확인하였다. Esterase 생산성 측면에서는 대수 성장기 초반에 induction 을 유도한 경우에 비해 최대 5.8배 생산성이 증가됨을 확인할 수 있었다. 따라서 본 연구를 통해 순수산소와 질소원의 공급을 통해 확립된 대장균 고밀도 배양방법을 기초로 IPTG 유도시간을 최적화 함으로써 Bacillus 유래 esterase의 최대 생산성을 확보할 수 있는 배양방법을 확립하였다.

• 대한한의학회지
• /
• 제29권2호
• /
• pp.116-132
• /
• 2008

Objective: This study investigated the effects of Bimanbang-1 (肥滿1號方: here in after referred to BMB-1) on the obese gene and obese inhibitory. Methods: C57BL/6 mice were induced by high fat diet. Mice were divided into three groups (normal, high fat diet with control, high fat diet with BMB-1 extract) and fed for 15 weeks. Items of this experimental study are as follows: body weight change, final body weight, the weight change of the adipocytes in body, the level change of LFT, NEFA and creatinine, the expression of ${\beta}3AR$ and leptin gene in primary adipocytes, the production change of leptin in primary adipocytes, the expression of ${\beta}3AR$, leptin and $TNF-{\alpha}$ in adipocytes tissue. Result: 1. All experimental groups showedthat the weight change decreased considerably and the high density group showedthat the final weight decreased considerably. 2. The high density group showed that the amount of the adipocyte in weight decreased considerably. 3. All experimental groups showedthat the amount of ALT decreased considerably, and AST decreased in the high density group. However, the amount of creatinine and glucose did not increase considerably. 4. All experimental groups showed that the amount of total cholesterol, LDL-cholesterol, triglyceride, and NEFA decreased, and HDL-cholesterol increased considerably. 5. The high density groups showedthat the amount of leptin decreased considerably. 6. All experimental groups showed that the revelation of ${\beta}3AR$ in primary adipose cell and 3T3-L1 cell increased considerably, and that the revelation of leptin and $TNF-{\alpha}$ in primary adipose cellsand 3T3-L1 cells decreased considerably. 7. All experimental groups showed that the size of adipocyte in adipocytes tissue decreased. 8. All experimental groups showed that the adipose vacuoles in liver tissue decreased considerably. Conclusion: The findings suggest that Bimanbang-1 causes weight loss and histological change, thus it may be effective to treat obesity.

• Carbon letters
• /
• 제2권1호
• /
• pp.72-75
• /
• 2001

The performance of Li-ion system based on $LiCoO_2$ and Graphite is well optimized for the 3C applications. The charge-discharge mode, the manufacturing process, the cell performance and the thermal reactions affecting safety has been explained in the engineering point of view. The energy density of the current LIB system is in the range of 300~400 Wh/l. In order to achieve the energy density higher than 500 Wh/l, the active materials should be modified or changed. Adopting new high capacity anode materials would be effective to improve energy density.

• 전기화학회지
• /
• 제6권3호
• /
• pp.174-177
• /
• 2003

Electric double-layer capacitors based on charge storage at the interface between a high surface area activated carbon electrode and an electrolyte solution are characterized by their long cycle-life and high power density in comparison with batteries. However, energy density of electric double-layer capacitors obtained at present is about 6 Wh/kg at a power density of 500W/kg which is smaller as compared with that of batteries and limits the wide spread use of the capacitors. Therefore, a new capacitor that shows larger energy density than that of electric double-layer capacitors is proposed. The new capacitor is the hybrid capacitor consisting of activated carbon cathode, carbonaceous anode and an organic electrolyte. Maximum voltage applicable to the cell is over 4.2V that is larger than that of the electric double-layer capacitor. As a result, discharged energy density on the basis of stacked volume of electrode, current collector and separator is more than 18Wh/l at a power density of 500W/l.

• 한국수소및신에너지학회논문집
• /
• 제26권2호
• /
• pp.127-135
• /
• 2015

High-Temperautre Polymer Electrolyte Membrane Fuel Cell (HT-PEMFC) with phosphoric acid-doped polybenzimidazole (PBI) membrane has high power density because of high operating temperature from 100 to $200^{\circ}C$. In fuel cell stack, heat is generated by electrochemical reaction and high operating temperature makes a lot of heat. This heat is caouse of durability and performance decrease about stack. For these reasons, heat management is important in HT-PEMFC. So, we developed HT-PEMFC model and study heat flow in HT-PEMFC stack. In this study, we placed coolant plate number per cell number ratio as variable and analysed heat flow distribution in stack.

• Transactions on Electrical and Electronic Materials
• /
• 제18권2호
• /
• pp.70-73
• /
• 2017

We investigated n-i-p type single junction hydrogenated amorphous silicon oxide solar cells. These cells were without front surface texture or back reflector. Maximum power point efficiency of these cells showed that an optimized device structure is needed to get the best device output. This depends on the thickness and defect density ($N_d$) of the active layer. A typical 10% photovoltaic device conversion efficiency was obtained with a $N_d=8.86{\times}10^{15}cm^{-3}$ defect density and 630 nm active layer thickness. Our investigation suggests a correlation between defect density and active layer thickness to device efficiency. We found that amorphous silicon solar cell efficiency can be improved to well above 10%.