• Proceedings of the KWS Conference
• /
• 1994.05a
• /
• pp.65-68
• /
• 1994

• Proceedings of the Korean Magnestics Society Conference
• /
• 2005.06a
• /
• pp.124-125
• /
• 2005

• KSTLE International Journal
• /
• v.1 no.1
• /
• pp.12-20
• /
• 2000

Nano-wear and friction of carbon overcoated laser-textured and mechanically-textured computer hard disk were characterised after contact start/stop (CSS) wear test. Various analytical and mechanical testing techniques were employed to study the changes in topography, roughness, chemical elements, mechanical properties and friction characteristics of the coating arising from the contact start/stop wear test These techniques include: the atomic force microscopy (AFM), the continuous nano-indentation test, the nano-scratch test, the time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and the auger electron spectroscopy (AES). It was shown that the surface roughness of the laser-textured (LT) bump and mechanically textured (MT) Bone was reduced approximately am and 7nm, respectively, after the CSS wear test. The elastic modulus and hardness values increased after the CSS test, indicating straining hardening of the top coating layer, A critical load was also identified fer adhesion failure between the magnetic layer and the Ni-P layer, The TOF-SIMS analysis also revealed some reduction in the intensity of C and $C_2$$F_59$, confirming the wear of lubricant elements on the coating surface.

• Transactions of Materials Processing
• /
• v.18 no.6
• /
• pp.465-470
• /
• 2009

The frictional behaviors of Cermets/Cr-Ceramics and Cu-Al coatings of piston ring were investigated. Friction tests were carried out by pin-on-disk test and materials properties of coating layer were analyzed by nano indentation tester. The effect of surface roughness of cylinder liner on the friction coefficient was analyzed. This study provided tribological data of hard and soft piston ring coatings against cylinder liner. The surface roughness does exert an influence on the average friction coefficient, with smoother surfaces generally yielding lower friction coefficients. In case of hard-coating, the scratch depth, width and pile-up height had close relationship with hardness. So the scratch width, depth and pile-up height increases with decreasing friction coefficient. But in case of soft-coating, the friction coefficients are strongly dependent on the morphological characteristics such as, scratch depth, width, pile-up height and elastic modulus.

• Korean Journal of Materials Research
• /
• v.12 no.5
• /
• pp.341-346
• /
• 2002

In order to improve the low wear resistance of Ti-6Al-4V alloy, plasma carburization treatment was newly carried out without consumption of its good specific strength and fatigue life over the temperature. Effect of the plasma carburization was analyzed and compared with the non-treated alloy by microstructural observation, structure characterization and mechanical property test. The plasma treated alloy formed a carburized layer of about 150$\mu\textrm{m}$ in depth from the surface, where a fine and hard particles of TiC and $V_4C_3$ were homogeneously dispersed through the layer. It was also found that an increase of the wear resistance, fatigue life and hardness, due to the hard and fine dispersoids.

• Geotechnical Engineering
• /
• v.1 no.2
• /
• pp.27-40
• /
• 1985

This study aims at the development of computer Program for the deformation analysis of soft clay layers, and using this computer program, study the constraint effect of deformation- heaving, lateral displacement-of the soft clay layers reinforced with sheet pile at the tip of banking or improvement of soft clay layer up to hard strata, under intact state (natural) and the state of vertical drain respectively. For this study, Biot's consolidation theories and modified Cam-clay theory for constitutive equation for FEMI were selected and coupled governing equation, and christian-Boehmer's technique was applied to solve the coupled relationship. The following results are obtained. 1. Sheet pile or improvement of soft clay layer to the hard strata work well against the settlement of neighboring ground. B. In view of restriction of heaving or lateral displacement, sheet pile is not supposed to be of use. 3. Sheet pile is of effect only when vertical drain is constructed for acceleration of consolidation and load increases gradually. B. The larger the rigidity of improvement of layer to hard strata is, the less settlement occurs.

• Journal of the Korean association of regional geographers
• /
• v.9 no.2
• /
• pp.169-179
• /
• 2003

The hardness and physical properties of soils were measured in hiking trails of Mt. Halla and Darangshiorum in Jeju Island to examine the characteristics and formative factors of an aquiclude induced by human trampling. The soil hardness, being generally the highest on trails, decreases outward and shows the lowest on adjacent slopes in a natural condition. The bulk density and solid phase also demonstrates a similar tendency, then implying that the aquiclude occurs in the central part of trails. Although the formation of a hard layer in trails is fundamentally attributed to human trampling, the environmental factors such as landform, lithology, soil and vegetation play a role in the occurrence of the aquiclude. Soil compaction varies with the gradient and location of trails which affects a transport and deposition of soil particles to produce a hard layer. Soil compaction also depends on the physical properties of soils including the soil texture largely affected by lithology. Vegetation is not directly related with the formation of a hard layer, but affects its dimensions through an enlargement rate of bare trails depending on the response and resistance of plants to human trampling.

• The KIPS Transactions:PartD
• /
• v.17D no.6
• /
• pp.383-394
• /
• 2010

Flash memory based SSDs are currently being considered as a promising candidate for replacing hard disks due to several superior features such as shorter access time, lower power consumption and better shock resistance. However, SSDs have different characteristics from hard disk such as difference of unit and time for read, write and erase operation and impossibility for over-writing. Because of these reasons, SSDs have disadvantages on hard disk based systems, so FTL(Flash Translation Layer) is designed to increase SSDs' efficiency. In this paper, we propose an advanced logical address mapping method for increasing SSDs' performance, which is named HAMM(Hybrid Address Mapping Method). HAMM addresses drawbacks of previous block-mapping method and super-block-mapping method and takes advantages of them. We experimented our method on our own SSDs simulator. In the experiments, we confirmed that HAMM uses storage area more efficiently than super-block-mapping method, given the same buffer size. In addition, HAMM used smaller memory than block-mapping method to construct mapping table, demonstrating almost same performance.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.984-985
• /
• 2014

This research investigates to analyze the effect of laser of thermally assisted magnetic recording system on diamond like carbon (DLC) layer of slider. We investigated a damaged DLC layer of slider with laser spot-induced damage and analyze the effect of the damaged DLC layer in slider dynamics. The damaged DLC layer resulted in change of flying height and air bearing stiffness pressure.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.28B no.12
• /
• pp.27-37
• /
• 1991

In this paper, the novel PLD (Preceding Layer Driven) MLP (Multi Layer Perceptron) neural network model and its learning algorithm is described. This learning algorithm is different from the conventional. This integer weights and hard limit function are used for synaptic weight values and activation function, respectively. The entire learning process is performed by layer-by-layer method. the number of layers can be varied with difficulty of training data. Since the synaptic weight values are integers, the synapse circuit can be easily implemented with CMOS. PLD MLP neural network was applied to English Characters, arbitrary waveform generation and spiral problem.