• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.05a
• /
• pp.104-109
• /
• 2002

In this paper, a statistical analysis of fatigue crack growth behavior under constant amplitude loads has been carried out. Fatigue crack growth tests were conducted on sixteen pre-cracked compact tension (CT) specimens of the pressure vessel (SPV50) steel in controlled identical load and environmental conditions. The assessment of the statistical distribution of fatigue crack growth experimental data obtained from SPV50 steel was studied and also the correlation of the parameter C and m in the Paris-Erdogan law was discussed. The probability distribution function of fatigue crack growth life seems to follow the 3-parameter Weibull. The fatigue crack growth rate seems to follow the 3-parameter Weibull and the log-normal distribution. The coefficient of variation (COV) of fatigue crack growth life was observed to decrease as the crack grows. A strong negative linear correlation exists between the coefficient C and the exponent m in Paris model. Fatigue crack growth rate data shows a normal distribution for both m and logC.

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.237-241
• /
• 1998

The growth orientation and the surface roughness of AIN/Si(111) films grown by radio frequency (RF) reactive magnetron sputtering were investigated using in-situ x-ray scattering technique and atomic force microscopy (AFM). AIN films were initially grown with the <001> preferred growth orientation under most growth conditions. As the film gets thicker, however, the growth orientation changes significantly, especially at high substrate temperature and high RF powers. We attribute the observed behavior to the competition between the surface energy that prefers the <001> growth orientation and the strain energy that randomizes the growth orientation. In addition, we investigated the evolution of the surface morphology during the growth using the x-ray reflectivity measurement.

• Korean Journal of Materials Research
• /
• v.25 no.4
• /
• pp.183-190
• /
• 2015

Fatigue crack growth rate tests were conducted as a function of temperature, dissolved hydrogen (DH) level, and frequency in a simulated PWR environment. Fatigue crack growth rates increased slightly with increasing temperature in air. However, the fatigue crack growth rate did not change with increasing temperature in PWR water conditions. The DH levels did not affect the measured crack growth rate under the given test conditions. At $316^{\circ}C$, oxides were observed on the fatigue crack surface, where the size of the oxide particles was about $0.2{\mu}m$ at 5 ppb. Fatigue crack growth rate increased slightly with decreasing frequency within the frequency range of 0.1 Hz and 10 Hz in PWR water conditions; however, crack growth rate increased considerably at 0.01 Hz. The decrease of the fatigue crack growth rate in PWR water condition is attributed to crack closure resulting from the formation of oxides near the crack tips at a rather fast loading frequency of 10 Hz.

• Korean Journal of Materials Research
• /
• v.31 no.9
• /
• pp.488-495
• /
• 2021

Solid state grain growth (SSCG) is a method of growing large single crystals from seed single crystals by abnormal grain growth in a small-grained matrix. During grain growth, pores are often trapped in the matrix and remain in single crystals. Aerosol deposition (AD) is a method of manufacturing films with almost full density from nano grains by causing high energy collision between substrates and ceramic powders. AD and SSCG are used to grow single crystals with few pores. BaTiO₃ films are coated on (100) SrTiO₃ seeds by AD. To generate grain growth, BaTiO₃ films are heated to 1,300 ℃ and held for 10 h, and entire films are grown as single crystals. The condition of grain growth driving force is ∆G_max < ∆G_c ≤ ∆G_seed. On the other hand, the condition of grain growth driving force in BaTiO₃ AD films heat-treated at 1,100 and 1,200 ℃ is ∆G_c < ∆G_max, and single crystals are not grown.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.06a
• /
• pp.41-44
• /
• 1997

Dispersion and flocculation behaviors of clay-ash powders in a slurry state were examined, and we have systematically investigated the effects of colloid/interfaces variables on slip properties and the rheological behavior of ash-clay slurry. Ash-clay slurries have been characterized on the basis of the time dependent rheology which was done out by the gel-curve test. Gel-curve for the coagulated slip shows interesting rheological behavior which was caused by the formation of the new network structure and the readsoption of the polysilicon hydroxo species on the particle surfaces.

• Nuclear Engineering and Technology
• /
• v.41 no.2
• /
• pp.143-148
• /
• 2009

The increasing power and other demands on PWR fuel is leading to a demand for cladding that has low corrosion but that should also be robust with regard to mechanical behavior, impact of the irradiation environment and the coolant chemistry. The Optimized $ZIRLO^{TM}$ cladding is an evolutionary development of $ZIRLO^{TM}$ taking advantage of the long experience of the ZIRLO cladding but has significantly improved corrosion behavior. Recently, operation of Optimized ZIRLO to above 73 kWd/kgU has shown a reduction of the corrosion of almost 50%.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.82-83
• /
• 2008

In the cases of high speed railway bridge, dynamic behavior analysis is important because of high passing velocity and moving load at the regular intervals, and the damping ratio is a major element in dynamic behavior analysis. In this paper, damping ratios were estimated by two methods and vibration type sections, and relationship between estimated damping ratio and representative value of bridge vibration. At the results, estimated damping ratio using all time of vibration were more stable then using only free vibration section. And in the case of using extended Kalman filter, estimated damping ratio were trend of growth by growth of representative value of bridge vibration. At last, it was shown that study about reliabilities of estimated damping ratios were need.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.856-860
• /
• 2002

The main objective of this study is to consider the effect of fatigue crack behavior on the variable depth of micro hole defects in SM20C at the symmetric position. The fatigue crack propagation test is performed by rotary bending fatigue test machine. The relationship between crack length(2a), cycles(N) and crack growth rate(da/dN) are investigated in this study. The result from the rotary bending fatigue test under the applied stress at 250MPa turned out that the fatigue life illustrated almost constant when the depth of symmetric micro hole deflects is both part A and B at the hope depth(h) = 0.5mm.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1998.06a
• /
• pp.81-86
• /
• 1998

The light aggregates were fabricated by sintering green bodies made form the fly ash-clay alip. The content of fly ashes in the slip could be increased up to 70wt.% due to controlled rheological behavior of the slip, and the green body of uniform microstructure could be obtained by DCC(Direct Coagulation Casting)method. The apparent density, microstructure and compressive strength for sintered bodies fired at 1100∼1200$^{\circ}C$ were evaluated. The properties of light aggregates fabricated depend on slip density, particle behavior in the slip and sintering conditions. The sintered body prepared by firing a green body made from slip of density 1.60 at 1150$^{\circ}C$/2hr satisfied conditions of a light aggregate as apparent density of 1.49${\pm}$0.02 and compressive strength of 584${\pm}$62kg/$\textrm{cm}^2$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.581-584
• /
• 2003

Most modeling about dynamic behavior of Antiferroelectric Liquid Crystal (AFLC) is limited to the hysteric characteristics of AFLC cells or thresholdless switching of frustrated AFLC cells. In this paper, domain growth of AFLC cells is modeled with extended bilayer model. When driving pulses that consist of a selection voltage, a bias voltage, and a reset voltage are applied to the AFLC cell, its dynamic behavior is simulated.