• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.681-689
• /
• 2010

We will demonstrate a novel topology for the feedforward amplifier. This amplifier does not use a delay element thus providing an efficiency enhancement and a size reduction by employing a distributed element negative group delay circuit. The insertion loss of the delay element in the conventional feedforward amplifier seriously degrades the efficiency. Usually, a high power co-axial cable or a delay line filter is utilized for a low loss, but the insertion loss, cost and size of the delay element still acts as a bottleneck. The proposed negative group delay circuit removes the necessity of the delay element required for a broadband signal suppression loop. With the fabricated 2-stage distributed element negative group delay circuit with -9 ns of total group delay, a 0.2 dB of insertion loss, and a 30 MHz of bandwidth for a wideband code division multiple access downlink band, the feedforward amplifier with the proposed topology experimentally achieved a 19.4 % power added efficiency and a -53.2 dBc adjacent channel leakage ratio with a 44 dBm average output power.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.11 no.1
• /
• pp.113-120
• /
• 1984

The author surveyed the tooth development of 50 cleft affected children(M: 34, F:16). The following results were obtained. 1. The difference between the chronologic age and dental age was 0.61 years in the cleft group and 0.15 years in the control group. The delay in tooth development was observed in the cleft group. 2, In the cleft group, there was no difference in the delay of tooth development between the boys and the girls. 3. In the cleft group, there was no difference in the delay of tooth development between the maxilla and the mandible. 4. The delay of tooth development was more severe in the bilateral cleft group than in the unilateral cleft group. 5. In the unilateral cleft, there was no difference in tooth formation between the cleft side and corresponding side.

• Journal of Industrial Technology
• /
• v.25 no.B
• /
• pp.221-229
• /
• 2005

We present a numerical analysis of the optimal group number for minimizing the average paging delay. In the analysis, we consider uniform distributions for location probability conditions and apply M/D/1 queueing model to paging message queues of cells. We also get the lower bounds of group numbers and investigate the minimum transmission capacity under average paging delay constraints. Minimizing the average paging delay is important because it means minimizing the amount of bandwidth used for locating mobile terminals. Therefore, the numerical results of this paper will be very useful in PCS system when designing its signalling capacity due to its simplicity and effectiveness.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.6
• /
• pp.300-305
• /
• 2004

In this paper, new design equations based on the pole-zero analysis for multi-layered interdigital stripline linear group delay bandpass filter with tap input ports are presented. As a design example, a four-pole group delay filter with center frequency of 2.14GHz, bandwidth of 160MHz, and group delay variation of $\pm$0.1nS for LTCC technology or multilayered PCB technology is designed. In the design process, it is not necessary to simulate the entire structure, as the simulation of half structures is sufficient. Good results can be attained after the optimizing process was performed three times using the proposed equations and a commercial EM simulator.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.8
• /
• pp.1444-1454
• /
• 2000

The implementation of IF group delay equalizer and its performance are presented for radio relay system applications, and measured results are in good agreement with the simulated ones based upon analytical formulations. For waveguide filter of 40㎒ channel spacing, equalized delay accuracy of about +/- 2.0nsec can be obtained only by constructing 4 stage delay circuits, which provides good performance in system BER curves compared with no filter case, and the difference is less than 1.0㏈ at $10^{-12}$ BER. So this scheme with simple hardware design can be used for correcting the distorted group delays mainly caused by wavegiude filters. To evaluate the designed group delay equalizer, various simulated and experimental results are shown here in conjunction with STM-1 signal of co-channel 64-QAM digital radio relay system.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.5
• /
• pp.766-776
• /
• 2008

The purpose of this study was 1) to identify the reasons for delay of decision making and the shopping information in internet shopping, 2) to classify consumers based on the clothing benefits, 3) and to examine the differences among consumer groups in the reasons for delay of decision making and the shopping information. The data were collected from a sample of 500 internet shopper aged from 20 to 40. This study used factor analysis, multiple regression analysis, Pearson's correlation analysis, cluster analysis and ANOVA. The results showed that the reasons for delay of decision making consisted of eight factors: Performance risk, Comparison shopping, Economic shopping, Social risk, Uncertainty, Expecting of market change, Product unsatisfaction, Passive shopping. The shopping information consisted of three factors: Product variety, Product information, Additional information. Five factors of clothing benefits were Economy, Figure compensation, Social position, Individuality, and Comfort. The respondents were classified into four groups by five factors of clothing benefits; Individuality seeking group, Low-benefits seeking group, Economy seeking group, Figure compensation/comfort seeking group. There were significant differences among groups in the reasons for delay of decision making and the shopping information among groups. Therefore, marketers need to provide different shopping information for delay closure by target groups.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.3
• /
• pp.533-541
• /
• 2001

In this paper, we proposed lowpass filter using all-pass sums of flat delay characteristics. this filter consisted of all-pass filter of parallel structure, the general analog filter is impossible to adjust the phase and the delay, using the Proposed filter, it has advantage to adjust them. And, we compared and analyzed this filter with passband width and magnitude characteristics, and the relation of group delay characteristics and cut-off frequency. Also, in order to obtain desired cut-off frequency, forming the weighing, we obtained desired cut-off frequency and group delay characteristics.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.12
• /
• pp.2626-2634
• /
• 1997

The purpose of multicasting is to reduce the network costs for transmitting the same traffic to multiple destinations. In this paper, an efficient delay-bounded multicasting routing algorithm is proposed, which satistifies the network conditions of cost minimization and can adjust the dynamic events, such as 'leave and/or join ones' from the multicast group. Also, our algorithm is designed for various network requirements such as the efficiet dynamic group support, high-quality data distribution, and adaptability to variable situation. After the delay tolerance and the maximum group size are determined according to network state and requirements for delay and cost, the dynamic delay-bounded multicast tree is constructed using partial multicast routing. We evaluate the performance of the proposed algorithm by running simulations on randomly generated test networks using a Sun Sparc 20 workstation. We were able to obtain good simulation resutls, which means solutions that lies between the minimum cost solution and the minimum delay one.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.739-745
• /
• 2006

This paper presents a method to control group delay tine using a resonance circuit. The group delay time adjuster(GDTA) that can control signal group delay time comprises a variable capacitance and a variable equivalent inductor. These are coupled in parallel at a node and also controlled by two bias voltages separately, A variable equivalent inductor is realized a transmission line terminated a variable capacitor. Group delay time can be controlled by change of capacitance and inductance, but the resonating frequency is fixed. When the proposed GDTA is fabricated on RFID Korean frequency band$(908.5{\sim}914 MHz)$, a group delay variation is obtained about 3 ns.

• Journal of the Institute of Convergence Signal Processing
• /
• v.8 no.3
• /
• pp.163-170
• /
• 2007

In this paper, we propose that the polyphase scaler whose performance to that of the bicubic method, has less complexity in hardware structure. In order to get the new information, proposed system is based on the group delay which is one of the digital filter characteristics. The performance of this system is superior to that of bicubic algorithm which is well known. Because the hardware structure is simpler than other image scalers, we can adopt this system for mobile devices easily. The previous polyphase filters make blurring noise which is generated by up-scaling. We replace polyphase filters by boost-up filter to get vivid image. The proposed scaler is verified by Xilinx Virtex2 FPGA and is used as digital Boom in mobile camera phone.