• 지질공학
• /
• 제27권4호
• /
• pp.489-500
• /
• 2017

심부 시추코어(900 m) 단층대에서는 검은 유리질이 특징인 슈도타킬라이트가 종종 산출된다. 폭이 수~20 cm인 슈도타킬라이트는 모암인 쥬라기 화강암과 선캄브리아기 각섬석편마암과 접촉하거나 교호하는데, 연성변형이나 약한 습곡구조를 수반한다. 슈도타킬라이트는 다양한 심도에서 산출되는데 조직과 두께 또한 약간 상이한 특징을 보여준다. 대부분의 시추코어에서는 취성변형이 우세하며, 단층비지는 주로 상부구간에서 발달하고, 슈도타킬라이트는 불규칙한 간격의 심도에서 나타난다. 주사전자현미경(SEM)으로 관찰하면, 기질내에 만곡된 극미립의 석영입자가 관찰되고, 슈도타킬라이트의 표면은 마이크론 스케일에서조차도 매끄러운 유리질 기질이 특징적인데, 이같은 현상은 본 지역의 슈도타킬라이트가 강한 지진활동에 의한 마찰용융에 의하여 생성되었음을 지시한다. X선회절 정량분석(XRD)에 의하면, 슈도타킬라이트는 석영, 장석, 각섬석과 같은 일차광물과 점토광물, 방해석, 유리기질물 등의 이차광물로 구성되어 있다. 이러한 광물조성은 슈도타킬라이트를 포함하는 단층파쇄대가 약 $300^{\circ}C$ 이하의 저온 또는 비교적 얕은 심도(약 10 km 내외)에서 형성되었음을 의미한다. 슈도타킬라이트는 강한 지진활동의 산물이므로, 이것의 산출특징 파악을 통하여 심부지반의 고기 지진활동 해석이나, 고준위방사성폐기물 처분장 후보지의 지반안정성에 대한 핵심적인 정보를 알 수 있다.

• 한국지반공학회논문집
• /
• 제38권8호
• /
• pp.7-15
• /
• 2022

대부분의 선행연구는 동결 삼축압축시험 수행 시, 몰드를 사용하여 시료를 조성하고 단방향으로 동결을 진행하였다. 이는 동결된 시료에 잔류응력이 발생할 가능성이 있기 때문에 인공동결공법이 적용된 지반을 모사하는데 한계가 있다. 본 연구에서는 기존 시험방법의 한계를 보완할 수 있는 시험장비 및 시험방법을 제안하고, 제안된 방법으로 온도 및 구속압력에 따른 동결 사질토의 역학적 특성을 평가하였다. 동결온도가 낮아질수록 동결 사질토는 취성이 증가하였고, 부동수분의 감소 및 얼음자체의 강도 증가로 인하여 강도가 증가하였다. 구속압력의 증가는 강도저감 효과를 발생시키는 압력융해 현상과 강도증진 효과를 발생시키는 흙 입자의 마찰력 증가 모두를 야기하였다. 이처럼 동결 사질토의 역학적 거동은 구속압력과 동결온도의 복합적인 영향을 받는 것으로 나타났다.

• Tribology and Lubricants
• /
• 제38권6호
• /
• pp.255-260
• /
• 2022

This research presents tetrahedral amorphous (ta-C) coating on the artificial tooth for improving the durability and functionality (esthtics, foreign body of tooth) by filtered cathodic vacuum arc (FCVA). A differentiated coating method is required for a ta-C coating on polymer owing to the low melting point of the polymer, inter-facial adhesion, low friction, and non-conductivity. Herein, ta-C coating is applied below 50℃, and the potential difference of the carbon plasma drawn to the substrate was controlled by applying a positive duct bias voltage without using a substrate bias voltage. Consequently, the ta-C coating with a thickness of 70nm using the duct bias condition of 20V with the highest plasma intensity satisfies the esthetics of the artificial tooth and had a 5B level of inter-facial adhesion. In addition, the composite hardness of ta-C/polymer is 380 MPa, and correlations with esthetics, sp³ bonding, and mechanical properties. The friction coefficient (CoF) of the ta-C coating in a water-lubricated environment is 0.07, showing a six-fold reduction in CoF compared with that of a polymer.

• 한국결정성장학회지
• /
• 제8권3호
• /
• pp.508-512
• /
• 1998

마이크로파(2.45GHz) 에너지를 이용한 소결법으로 $1100^{\circ}C$~$1300^{\circ}C$의 온도범위에서 반도체 세라믹스인 $Mn_3O_4{\cdot}Co_3O_4{\cdot}3NiO$ 조성의 NTC 서미스터를 소결하였으며, 그 전기적 특성을 조사하였다. 소결온도가 높아질수록 소결밀도가 높은 치밀한 소결체를 얻을 수 있었으며, 25~$85^{\circ}C$ 범위의 온도변화에 따른 전기저항변화 특성으로부터 구한 비저항 $B_{25^{\circ/85^{\circ}}$ 정수는 3100~3200K이었다. 마이크로파 하이브리드, 소결법으로 소결된 시편과 일반소결법으로 소결된 시편을 비교하면 소결특성과 전기적물성에서 비슷한 결과를 얻을 수 있었다. 마이크로파 에너지를 이용한 소결공정은 20분 안에 완료되는 짧은 시간의 급속소결법으로 공정 시간과 에너지를 크게 절감할 수 있었다.

• 한국의상디자인학회지
• /
• 제19권2호
• /
• pp.39-48
• /
• 2017

Transfer printing is a method to combine printing and dyeing technology by the use of sublimation. It is an environmentally-friendly printing method that saves costs, reduces the production processes by the omission of the washing process, and saves time by maintaining quality. Due to the development of transfer printing, a high value added printing technology is available now but color fastness to sublimation of the printing products is still low since there are few dyes that have an affinity to the fabrics and the application technology is still inadequate. Specially, in case of high concentration black dyes, eco-label type black dyes, which is a substitution for general dispersal dyes, have been developed while general dispersal black dyes are still used, creating issues such as color differences on the surface and back side of the fabrics and contamination by friction after transfer printing. There are also some restricted substances such as allergens. To address these issues, high concentration black dyes and application technology that are environmentally-friendly and that have over 16 K/S through the use of single dyes with excellent color fastness, fixation ability, and similar melting temperature were developed for this study.

• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.315-319
• /
• 2008

This paper presents the interface bonding characteristics between a phosphor bronze and a steel plate for pin-bush bearings. The pin-bush bearing is an important component in which is used to reduce a friction loss and a wear against the piston pin. The pin-bush bearing is manufactured by hot-pressing a phosphor bronze and a back metal of a steel plate. This paper investigated the bonding interface characteristics in which is manufactured by melting a copper based bronze and a steel plate. The hardness from the inner surface of a bronze to the outer one of steel has been measured using a Vickers hardness tester. The experimental results show that the hardness of a bronze is superior to that of the conventional bronze and the transient hardness of pin-bush bearings is gradually increasing to the hardness of the steel back metal. This means that the bonding interface zone of pin-bush bearings may be fabricated by defusing a bronze to the steel plate due to a density difference between two materials.

• 한국주조공학회지
• /
• 제37권4호
• /
• pp.115-122
• /
• 2017

The aim of this research is to evaluate the wear properties of (TiB+TiC) paticulate reinforced titanium matrix composites (TMCs) by in-situ synthesis. Different particle sizes (1500, $150{\mu}m$) and contents (0.94, 1.88 and 3.76 mass% for Ti, 1.98 and 3.96 mass% for the Ti6Al4V alloy) of boron carbide were added to pure titanium and to a Ti6Al4V alloy matrix during vacuum induction melting to provide 5, 10 and 20 vol.% (TiB+TiC) particulate reinforcement amounts. The wear behavior of the (TiB+TiC) particulate reinforced TMCs is described in detail with regard to the coefficient of friction, the hardness, and the degree of reinforcement fragmentation during sliding wear. The worn surfaces of each sliding wear condition are shown for the three types of wear studied here: transfer layer wear, particle cohesion wear and the development of abrasive areas. The fine reinforcements of TMCs were easily fragmented from the Ti matrix as compared to coarse reinforcements, and fragmented debris accelerated the decrease in the wear resistance.

• 대한원격탐사학회지
• /
• 제37권1호
• /
• pp.1-11
• /
• 2021

This study measures the change of ice flow velocity of David Glacier, one of the fast-moving glaciers in East Antarctica that drains through Drygalski Ice Tongue. In order to effectively observe the rapid flow velocity, we applied the offset tracking technique to Sentinel-1A SAR images obtained from 2016 to 2020 with 36-day temporal baseline. The resulting velocity maps were averaged and the two relatively fast points (A1 and A2) were selected for further time-series analysis. The flow velocity increased during the Antarctic summer (around December to March) over the four years' observation period probably due to the ice surface melting and reduced friction on the ice bottom. Bedmap2 showed that the fast flow velocities at A1 and A2 are associated with a sharp decrease in the ice surface and bottom elevation so that ice volumetric cross-section narrows down and the crevasses are being created on the ice surface. The local maxima in standard deviation of ice velocity, S1 and S2, showed random temporal fluctuation due to the rotational ice swirls causing error in offset tracking method. It is suggested that more robust offset tracking method is necessary to incorporate rotational motion.

• 한국자동차공학회논문집
• /
• 제24권4호
• /
• pp.463-470
• /
• 2016

In this paper, the characteristics analysis of LMD track, such as including track structure, track wear resistance and track thickness, were analyzed to enhance the deposition efficiency using a diode-pumped disk laser. SKD61 hot work steel plate and Fe based AISI M2 alloy were used as a the substrate and powder for the LMD process, respectively. The laser power, track pitch and powder feed rate among LMD parameters were adopted to estimate the deposition efficiency. As the laser power is increased, heat input and melting pool on the substrate is grown also increases, so resulting in the increased LMD track thickness was increased. Through EPMA mapping analysis of the cross-section in the LMD track, it was observed that all the elements are evenly distributed inside. Therefore, the entire hardness in the LMD track is expected to be almost uniform regardless of location. The characteristics of the LMD specimen were excellent compared to the STD11 specimen in terms of the wear track width and the wear rate as well as the coefficient of friction. Especially the wear rate of LMD specimen has been significantly reduced by 60 % or more. From Based on the experimental results, the prediction formula of LMD thickness was calculated by using laser power, track pitch and powder feed rate.

• 태양에너지
• /
• 제4권2호
• /
• pp.13-28
• /
• 1984

Direct Absorption Receiver and Thermal Storage System is a complex problem. This paper describes only characteristic of fluid flow on the receiver. The fluid thicknesses of Molten Salts (Melting Point : $397^{\circ}C$) flowing on the receiver of modified protopype ($10m{\times}10m$) were calculated theorectically, changing the receiver slope from 60 degree to 85 degree (5 steps). The receiver temperatures were $430^{\circ}C$ at the top part and $950^{\circ}C$ at the low part. The flow thickness of the Molten Salts at the top part of the receiver are around 1.9mm in the case of maximum insolution ($50{\times}10^6$juoule/sec; 58.898kg/sec of flow rate) and 2.0mm at the low part. In the case of 3/10 of maximum insolation (flow rate = 17.669kg/sec) the flow thickness at the top part are around 0.9mm and 0.4mm at the low part, and in the case of 1/10 of maximum insolation (flow rate = 5.889 kg/see) the flow thickness at the top part are around 0.6mm and 0.3mm at the low part. From experimental measurements of a normal fresh water thickness flowing on the model plate ($12.7cm{\times}111.76cm$), around 0.8mm at the top part of the plate and around 0.7mm at the low part were obtained in the case of maximum insolation (flow rate = 0.12496 kg/see). In the case of 3/10 (flow rate = 0.03748 kg/see) and 1/10 (flow rate = 0.012496 kg/see) of maximum insolation, around 0.5mm and 0.4mm at the top part, and around 0.3mm and 0.2mm at the low part were obtained respectively. The reason why the thickness of the Molten Salts increase at the low part of the receiver only in case of maximum insolation is that decreasing rate of the viscosity of the Molten Salts is larger than decreasing rate of the density of the Molten Salts during temperature increase from the top to the low receiver plate and decrease of the fluid velocity in accordance with continuity principle. In all cases without the above maximum insolation, the thickness of the Molten Salts and the fresh water decreased at the low part of the plate because of gravity force effects rather than friction effects and of continuity principle. All simillar flow patterns were obtained through all cases of the insolation making an exception of only maximum insolation.