• Journal of Magnetics
• /
• v.21 no.1
• /
• pp.78-82
• /
• 2016

Cogging torque will affect the performance of a permanent magnet Brushless DC Motor (BLDCM), thus the reduction of cogging torque is key for BLDCM optimization. In this paper, the phase shifting of cogging torque for a fractional-slot concentrated winding BLDCM is analyzed using the Maxwell tensor method. Moreover, a 9-slot 10-pole concentrated winding BLDCM driven by ideal square waveform is studied with the finite element method (FEM). An effective method to reduce the cogging torque is obtained by adjusting the slot opening. In addition, the influences of different slot openings on back electromotive force (back-EMF), air gap flux density and flux linkage are investigated and experimentally validated using the prototype BLDCM.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.145-147
• /
• 1999

A voice type Moving Coil Linear Oscillatory Actuator(MC-LOA) has unbalanced magnetic circuit structure. Its asymmetric magnetic flux distribution along the mover directions causes shifting of displacement center to one side. Therefore, this paper analyzes both thrust and displacement characteristics and settles the unbalanced flux problem by performing shape optimization. The propriety of the improved design model has been verified by dynamic analysis based on the coupling of kinetic and electric equations.

• Membrane and Water Treatment
• /
• v.10 no.6
• /
• pp.417-429
• /
• 2019

Poly Sulfone nanofibers were electrospun to fabricate membranes of different characteristics. To fabricate the fiber mats, polymer concentration, flowrate, and current density were determined as the most influencing factors affecting the overall performance of the membranes and studied through Response Surface Methodology. The Box-Behnken Design method (three factors at three levels) was used to design, analyze, and optimize the parameters to achieve the best possible performance of the electrospun membranes in forward osmosis process. Also, internal concentration polarization that characterizes the efficiency of the forward osmosis membranes was determined to better assess the overall performance of the fabricated electrospun membranes. Water flux to reverse salt flux was considered as the main response to assess the performance of the membranes. As confirmed experimentally, best membrane performance with the minimal structural parameter value could be achieved when predicted optimal values were used to fabricate the membranes through electrospinning process.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.7
• /
• pp.753-761
• /
• 2005

In this study, pretreatment of organic matters with $MIEX^{(R)}$ was evaluated using bench-scale experimental procedures on four organic matters to determine its effect on subsequent UF membrane filtration. For comparison, coagulation process was also used as a pretreatment of UF membrane filtration. Moreover, the membrane fouling potential was identified using different fractions and molecular weights of organic matters. From the removal property of MW organic matters by coagulation process for the sample water NOM and AOM, the removal efficiency of high MW organic matters were much higher than those of low MW organic matters. It was shown that the removal efficiency of high MW organic matter more than 10 kDa was lower than that of low MW organic matter for $MIEX^{(R)}$ process. For the change of permeate flux by the pretreatment process, $MIEX^{(R)}$+UF process showed high removal efficiency of organic matter as compared with coagulation-UF processes, but high reduction rate of permeate flux was presented through the reduction of removal efficiency of high MW organic matter. From sequential filtration test results in order to examine the effect of MW of organic matter on membrane fouling, it was found that the membrane foulant was occurred by high MW organic matter, and the DOC of organic matter less than 0.5 mg/L was working as the membrane foulant. In the case of sample water composed of low MW organic matter less than 10 kDa, since the low MW organic matter less than 10 kDa has high removal efficiency by $MIEX^{(R)}$, low reduction rate of permeate flux is obtained as compared with coagulation-UF processes. In summary, it is required to conduct the research on physical/chemical characteristic of original water before pretreatment process of membrane process is selected, and a pertinent pre-treatment process should be employed based on the physical/chemical characteristic of original water.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.35 no.8
• /
• pp.1051-1056
• /
• 2006

Response surface methodology was used to investigate the quality of clarified mixed apple and carrot juices using ultrafitration. Apple and carrot juices were blended at the ratio of 1:3, 1:1, and 3:1. A three-variable, three-level central composite design was employed where the independent variables were the blend ratio, temperature and average transmembrane pressure (ATP). With increasing temperature and pressure, flux linearly increased regardless of blending ratio. Blend juice with 75% apple showed the highest soluble sugar and total sugar content in apple and carrot blend juices. Soluble solid contents were more affected by blending ratio than temperature and ATP. Total sugar contents were greatly affected by temperature; increasing temperature led to higher total sugar content up to $25^{\circ}C$. Higher carrot ratio led to higher vitamin C content. In general, higher acidity was achieved by higher apple content and acidity was increased with increasing temperature. Turbidity increased for all samples as APT increased, with the blending ratio of 1:1 (apple:carrot) showing the highest turbidity. Viscosity was greatly changed in the blending ratio of 3:1 (apple:carrot) juice. The polynomial models developed by RSM were satisfactory to describe the relationships between the studied factors and the responses. Analytical optimization gave $flux=0.216\;L/m^2.h$, soluble $solids=10.39^{\circ}Brix$, total sugar=71.32 mg/mL, vitamin C=315.18 mg%, acidity=7.78 mL, turbidity=0.017, and viscosity=1.44 cp, when using a $temperature=44.97^{\circ}C$, ATP=113.57 kPa, and blend ratio=28.50%.

• Journal of Radiation Protection and Research
• /
• v.30 no.2
• /
• pp.55-60
• /
• 2005

The evaluation of neutron flux distribution was performed for the ex-core detector design of SMART-P. DORT and MCNP code were used for the calculation of energy-dependent neutron flux distribution at 100% full power condition. Two code results show that maximum thermal flux appears at the $1^{st}$ water region in IST region and agree within 10% difference. In addition, another evaluation was performed code with assumptions that cote was composed of fission source and control rod without fuel assemblies. These assumptions make neutron count rate to be minimized. As a results, maximum thermal flux showed $6.99{\times}10^{-2}(n/cm^2-sec)$, when the strength of initial fission source was assumed as $1.0{\times}10^8(n/sec)$. The main reason of these results is due to the thermalization of fast neutrons in the water region and thermal flux is proportional to 80% of total neutron flux. Therefore, optimization of filler material of detector guide tube, position of installation and axial length of detector segments is necessary for the design of ex-core detector to enhance the neutron count rate and above results could be used in ex-core detector design as a fluence requirement.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1646_1647
• /
• 2009

In this paper, Takagi-Sugeno(T-S) fuzzy controller and search method are developed for efficiency optimization of induction motors(IMs). The proposed control scheme consists of efficiency controller and adaptive backstepping controller. A search controller for which information of input of T-S fuzzy controller is included in efficiency controller that uses a direct vector controlled induction motor. A sliding mode observer is designed to estimate rotor flux and an adaptive backstepping controller is used to control of speed of IMs. Simulation results are presented to validate the proposed controller.

• Journal of Magnetics
• /
• v.19 no.4
• /
• pp.411-417
• /
• 2014

This paper presents the shape optimization of a permanent magnet synchronous motor to reduce the torque ripple and iron loss. Specifically, the harmonics of the electromotive force and cogging torque are decreased by adjusting the permanent magnet arrangement and non-uniform air gap length. In addition, an additional flux path along the q-axis is proposed with a unique rotor shape to increase the q-axis inductance and reluctance torque. The improvement in the performance of the proposed model is verified with simulated and experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.587-590
• /
• 2000

The new core making method economized on core sand requested. The new method is heating core box until it reaches reasonable temperature and then spraying core sand with core binder into core box. Inner temperature distribution have to uniform in order to form core of uniform thickness. Therefore, in this study we treat of inner temperature distribution of core box in priority. First, determine proper torch number. Next, optimize the torch position to minimize the average of absolute deviation(AVEDEV) of inner temperature. The results are as followed : 1. The torch number that makes inner temperature distribution about $300^\circ{C}$ uniformly is 25. 2. When $S_H$ and $S_V$ is 0.7, the torch position is optimized and AVEDEV is 5.85.

• Progress in Superconductivity and Cryogenics
• /
• v.7 no.1
• /
• pp.17-20
• /
• 2005

We has designed, fabricated, and measured a Single flux quantum (SFQ) toggle flip-flop (TFF). The TFF is widely used in superconductive digital electronics circuits. Many digital devices, such as frequency counter, counting ADC and program counter be used TFF Specially, a program counter may be constructed based on TFF We have designed the newly TFF and obtained high bias margins on test. In this work, we used two circuit simulation tools, WRspice and Julia, as circuit optimization tools. We used XIC for a layout tool. Newly designed TFF had minimum bias margins of +/- $37\%$ and maximum bias margins of +/-$37\%$(enhanced from +/- $37\%$). The designed circuits were fabricated by using Nb technology The test results showed that the re-optimized TFF operated correctly on 100kHz and had a very wide bias margins of +/- $53\%$.