• Polymer(Korea)
• /
• v.34 no.6
• /
• pp.540-546
• /
• 2010

In this manuscript, in order to reduce methanol permeability and, at the same time, to increase proton conductivity THS-PSA containing silica compound, responsible for methanol permeability reduction, and sulfonic acid, responsible for proton conductivity enhancement, was applied onto PVA/PSSA-MA membranes. And in order to improve durability, the resulting membranes, PVA/PSSAMA/THS-PSA, were exposed to 500ppm F2 gas at varying reaction times. The surface-fluorinated membranes were characterized through the measurement of contact angles, thermo-gravimetric analysis, and X-ray photoelectron spectroscopy to observe the physico-chemical changes. For the evaluation of the electro-chemical changes in the resulting membranes, its water contents, ion exchange capacity, proton conductivity, and methanol permeability were measured and then compared with the commercial membrane, Nafion 115. Finally, the membran electrode assembly(MEA) was prepared and the cell voltage against the current density was measured. As fluorination time increased, the contents of F2 increased up to maximum 4.3% and to depth of 50 nm. At 60 min of fluorination, the proton conductivity was 0.036 S/cm, larger than Nafion 115 at 0.024 S/cm, and the methanol permeability was $9.26E-08cm^2/s$, less than Nafion 115 at $1.17E-06cm^2/s$.

• Journal of Adhesion and Interface
• /
• v.18 no.3
• /
• pp.127-133
• /
• 2017

In this study, to develop the adhesives with improved waterproof properties for display application, UV-curable urethane acrylate oligomers containing a fluorine moiety were synthesized from hydrogenated polybutadiene diol (HLBH-P2000), perfluoropolyether diol (HTPFPE), isophorone diisocyanate (IPDI) and 2-hydroxyethyl acrylate (HEA). The properties which were related waterproof performance such as contact angle, surface energy and water vapor transmission ratio (WVTR) of synthesized fluorine induced urethane acrylate oligomers were measured. As the HTPFPE content increased, the contact angle also increased from 97.9 degree to 104.4 degree. The surface energy and WVTR decreased as the HTPFPE content increased. The adhesion strength also decreased according to the HTPFPE content increased, and the adhesion strength reduction had greatly increased as the HTPFPE content increased. The findings of this study will be beneficial for developing waterproofing adhesives in the field of display which has recently been a waterproof issue.

• Polymer(Korea)
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2010

To enhance the transport properties of gas separation membrane, we prepared 6FDA-6FpDA based polyimide membrane with PMMA-graft-silica nanoparticles. The silica was grafted PMMA which is miscible with 6FDA-based polyimide after surface treatment by 3-methacryloxypropyltrimethoxysilane ($\gamma$-MPS). The untreated silica/6FDA-6FpDA membrane showed greater permeability and less selectivity than PMMA-g-silica/6FDA-6FpDA due to its low dispersion. The transport properties of PMMA-g-silica/6FDA-GFpDA membrane were measured as a function of filler concentration. These membranes were evaluated using pure gases (He, $O_2$, $N_2$, $CO_2$). The increase in permeation was attributed to changes in the free volume distribution until 1 wt%. After 1 wt%, the permeability was decreased by excess silica which decreased effective area in polymer matrix. The selectivity was decreased with increasing permeability on the whole. However, the selectivity of $CO_2$ showed more enhance value.

• Journal of the Korean Vacuum Society
• /
• v.7 no.4
• /
• pp.368-373
• /
• 1998

As device dimensions approach submicrometer size in ULSI, the demand for interlayer dielectric materials with very low dielectric constant is increased to solve problems of RC delay caused by increase in parasitic resistance and capacitance in multilevel interconnectins. Fluorinated amorphous carbon in one of the promising materials in ULSI for the interlayer dielectric films with low dielectric constant. However, poor thermal stability and adhesion with Si substrates have inhibited its use. Recently, amorphous hydrogenated carbon (a-C:H) film as a buffer layer between the Si substrate and a-C:F has been introduced because it improves the adhesion with Si substrate. In this study, therfore, a-C:F/a-C:H films were deposited on p-type Si(100) by ECRCVD from $C_2F_6, CH_4$and $H_2$gas source and investigated the effect of forward power and composition on the thickness, chemical bonding state, dielectric constant, surface morphology and roughness of a-C:F films as an interlayer dielectric for ULSI. SEM, FT-IR, XPS, C-V meter and AFM were used for determination of each properties. The dielectric constant in the a-C:F/a-C:H films were found to decrease with increasing fluorine content. However, the dielectric constant increased after furnace annealing in $N_2$atomosphere at $400^{\circ}C$ for 1hour due to decreasing of flurorine content. However, the dielectric constant increased after furnace annealing in $N_2$atmosphere at $400^{\circ}C$ for 1hour due to decreasing of fluorine concentration.

• Membrane Journal
• /
• v.16 no.3
• /
• pp.221-229
• /
• 2006

This study is about the preparation and characterization of sulfonated random copolymer membranes containing perfluorocyclobutane (PFCB), fluorenyl, and sulfonyl units. The polymers were prepared through three synthetic steps, that is, the synthesis of a trofluorovinylether-terminated monomer, its thermal polymerization, and post-sulfonation using chlorosulfonic acid. A series of sulfonated random copolymers with different ion exchange capacity (IEC) were prepared by changing contents of fluorenyl uints in polymers with fixed molar ratio of chlorosulfonic acid during the post-sulfonation reaction. All the synthesized compounds were characterized by FT-lR, $^1H-NMR$, $^{19}F-NMR$, and Mass spectroscopy. As the content of sulfonated fluorenyl units increased, the IEC, water uptake, and ion conductivity of the sulfonated random copolymer membranes increased. The sulfonated random copolymer S-1 and S-2 showed higher values of ion conductivity than the Nafion-115 in a wide range of temperatures ($25{\sim}80^{\circ}C$).

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.53-59
• /
• 2005

In this study, the supercritical electroplating was investigated by forming macroemulsion of electroplating solution using surfactant in supercritical $CO_2$. The fluorinated analogous AOT surfactant, sodium salt of bis (2,2,3,3,4,4,5,5-octafluoro-1-pentanol) sulfosuccinate which has both '$CO_2$ philic' chains and 'hydrophilic' head group was used as a surfactant, and Ni plate and Cu plate were used as the anode and the cathode, respectively. Electroplating was carried out in the conventional method and the supercritical macroemulsion and both results were compared. The supercritical electroplating was carried out in various concentration of surfactant such as 2, 4, 7 wt%, the volume ratio of Ni-plating solution to $CO_2$ was varied in the range of 10-70 vol%, and propane was used as a supercritical fluid instead of $CO_2$. According to the experimental results, the plated surface of Ni on Cu plate performed in supercritical macroemulsion was better than that, in conventional state. In the image of Ni surface plated on Cu plate in supercritical state, there were fewer pin-holes and pits comparing with that in the conventional process. The current and conductivity was increased as the volume ratio of Ni-plating solution to $CO_2$ was increased and the current and the amount of Ni plated on Cu plate were decreased as the concentration of surfactant become higher. In addition, in case of the continuous phase, using $CO_2$ was more effective than using $CO_2$.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.2
• /
• pp.39-44
• /
• 2016

Oxygen reduction reaction in the fuel cell (ORR) plays a dominant role in the overall reaction. In addition, the low compatibility between the membrane and the binder consisted of different materials, greatly reduces the efficiency of the fuel cell performance. In view of these two problems, geometrically modified copolymers with 9.9_Bis (4-hydroxyphenyl) were synthesized via condensation reaction instead of conventional biphenol and were adopted as hydrocarbon ionomer binders. By utilizing these binders, two kinds of MEAs using fluorinated Nafion membrane and hydrocarbon based membrane were manufactured in order to electrochemical performance evaluation. With current-voltage curves, there was no significant difference in the 0.6 V when two types of membrane were applied. Also, tafel slope became considerably lower as compared to the Nafion membrane. Thus, it is determined that the new hydrocarbon binder is expected to contribute the improvement in performance of fuel cells.

• Membrane Journal
• /
• v.16 no.1
• /
• pp.16-24
• /
• 2006

We report on the preparation and characterization of sulfonated polymer membranes containing perfluorocyclobutane (PFCB) units and fluorene units. The polymers were prepared through three synthetic steps, that is, the synthesis of a trifluorovinylether-terminated monomer, its thermal polymerization, and post-sulfonation using chlorosulfonic acid. A series of sulfonated polymers with different ion exchange capacity (IEC) were prepared by changing the content of chlorosulfonic acid during the post-sulfonation reaction. All the synthesized compounds were characterized by FT-IR, $^{1}H-NMR,\;^{19}F-NMR$, and Mass spectroscopy. As the content of chlorosulfonic acid increased, the SD, IEC, water uptake, and ion conductivity of the sulfonated polymer membranes increased. The sulfonated polymer 4 showed higher values of ion conductivity than the Nafion-$115^{\circledR}$ in a wide range of temperatures ($25{\sim}80^{\circ}C$).

• Korean Chemical Engineering Research
• /
• v.57 no.6
• /
• pp.749-757
• /
• 2019

Methyltrimethoxysilane (MTMS) and trimethylethoxysilane (TMES) as starting materials were dissolved in various types of solvents, and hydrolysis with water and polycondensation reaction were carried out using various types of catalysts to prepare non-fluorinated water-repellent coating solutions. The coating solutions were spin-coated on cold-rolled steel sheets, and thermally cured to prepare water-repellent coating films. The effect of types of catalysts and solvents on the water repellency of the resulting coating films was investigated during this process. When hydrochloric acid and nitric acid, which are strong acids, were used as catalysts, the solutions showed a white opaque state due to the aggregation of siloxane polymers. On the other hand, when acetic acid, phosphoric acid, and oxalic acid, which are weak acids, were used, they were in a stable and transparent state without precipitation. As a result, the contact angles of the coated films, prepared from hydrochloric acid and nitric acid, were $58^{\circ}$ and $92^{\circ}$, respectively, showing low water repellency. On the other hand, when acetic acid, phosphoric acid, and oxalic acid were used, the contact angles of the coated films were $101^{\circ}$, $103^{\circ}$ and $116^{\circ}$, respectively, showing high water repellency. In addition, when isopropanol and ethanol were used as solvents, phase separation occurred in the solutions due to the aggregation of siloxane polymers. On the other hand, when methanol, ethyl acetate, and methyl ethyl ketone were used as solvents, the solutions were transparent and showed a stable state without sedimentation.

• Applied Chemistry for Engineering
• /
• v.32 no.6
• /
• pp.653-658
• /
• 2021

Polyvinylidene fluoride (PVDF) is a promising coating material because of its outstanding processability. The PVDF coating, however, has limitations in anti-corrosion application due to its weak hydrophobicity compared to that of other fluoropolymers. In this study, plasma fluorination was performed using carbon tetrafluoride (CF₄) gas to improve anti-corrosion properties of PVDF. The fluorine content and hydrophobicity of PVDF were investigated in different CF₄ flow rates, followed by the determination of anti-corrosion properties. The fluorine content on the surface of the PVDF film increased by up to 46.70%, but the surface free energy was independent of CF₄ flow rate. Meanwhile, the surface roughness of the PDVF film tended to increase by up to 150% and then decrease with increasing CF₄ flow rate. It is considered that the plasma fluorination affects the surface free energy due to the introduction of fluorine functional groups and surface etching. In addition, the degree of corrosion of the PVDF-coated Fe plate was significantly reduced from 49.2% to 19.0% compared to that of the uncoated Fe plate. In particular, the degree of corrosion of the fluorinated PVDF-coated Fe plate was 13.6%, which was 28.4% lower than that of the PVDF-coated Fe plate, showing improved anti-corrosion protection.