• Journal of the Korean Vacuum Society
• /
• v.22 no.3
• /
• pp.156-161
• /
• 2013

We fabricated transparent conductive electrodes with silver (Ag) nanofibers by electrospinning process. Ag nanofibers have high aspect ratio and fused junctions which result in low sheet resistance. Electrospinning is a fast and efficient process to fabricate continuous one-dimensional (1D) nanofibers. Ag/polymer ink were prepared in polymer matrix solution by a sol-gel method. Then, Ag/polymer nanofibers precursors are heated at $200{\sim}500^{\circ}C$ in air for 2 h to eliminate partially the polymers. The topographical features of the Ag nanofibers were characterized by FE-SEM, and the electrical property was analyzed through I-V measurement system. Finally, optical property was measured using UV/VIS spectroscopy. The transparent conductive electrodes with Ag nanofibers exhibited a sheet resistance (Rs) of $250{\Omega}/sq$ at a transparency (T) of 83%. Transparent conductive films, contain the Ag nanofibers as conductive materials, have good electrical, optical, and mechanical properties. Therefore, it is expected to be useful for the application of flexible display in the future.

• Journal of the Korean Vacuum Society
• /
• v.20 no.5
• /
• pp.356-360
• /
• 2011

Indium oxide ($In_2O_3$) single layer and $In_2O_3$/copper (Cu) bi-layer films were prepared on glass substrates by RF and DC magnetron sputtering without intentional substrate heating. In order to determine the effect of the Cu bottom layer on the optical, electrical and structural properties of $In_2O_3$ films, 3-nm-thick Cu film was deposited on the glass substrate prior to deposition of the $In_2O_3$ films. As-deposited $In_2O_3$ films had an optical transmittance of 79% in the visible wavelength region and a sheet resistance of 2,300 ${\Omega}/{\square}$, while the $In_2O_3$/Cu film had optical and electrical properties that were influenced by the Cu bottom layer. $In_2O_3$/Cu films had a lower sheet resistance of 110 ${\Omega}/{\square}$ and an optical transmittance of 71%. Based on the figure of merit, it can be concluded that the Cu bottom layer effectively increases the performance of $In_2O_3$ films for use as transparent conducting oxides in flexible display applications.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.578-584
• /
• 2017

$SiO_2$ buffer layer (100 nm) has been deposited on PET substrate by electron beam evaporation. And then, IZTO (In-Zn-Sn-O) thin film has been deposited on $SiO_2$/PET substrate with different RF power of 30 to 60 W, working pressure, 1 to 7 mTorr, by RF magnetron sputtering. Structural, electrical and optical properties of IZTO thin film have been analyzed with various RF powers and working pressures. IZTO thin film deposited on the process condition of 50 W and 3 mTorr exhibited the best characteristics, where figure of merit was $4.53{\times}10^{-3}{\Omega}^{-1}$, resistivity, $4.42{\times}10^{-4}{\Omega}-cm$, sheet resistance, $27.63{\Omega}/sq.$, average transmittance (400-800 nm), 81.24%. As a result of AFM, all the IZTO thin film has no defects such as pinhole and crack, and RMS surface roughness was 1.147 nm. Due to these characteristics, IZTO thin film deposited on $SiO_2$/PET structure was found to be a very compatible material that can be applied to the next generation flexible display device.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.674-680
• /
• 2017

Touch Screen Panel (TSP) is a widely used personal handheld device and as a large display apparatus. This study examines micro bump fabrication technology for TSP test process. In the testing process, as TSP is changed, should make a new micro bump for probing and modify the testing program. In this paper we use a maskless lithography system to confirm the potential to fabricatemicro bump to reducecost and manufacturing time. The requiredmaskless lithography system does not use a mask so it can reduce the cost of fabrication and it flexible to cope with changes of micro bump probing. We conducted electro field simulation by pitches of micro bump and designed the lithography pattern image for the maskless lithography process. Then we conducted Photo Resist (PR) patterning process and electro-plating process that are involved in MEMS technology to fabricate micro bump.

• Journal of the Korean Society for Library and Information Science
• /
• v.44 no.4
• /
• pp.203-230
• /
• 2010

This study analyzed the development and growth of folksonomy by examining tags associated with 40 bestsellers on LibraryThing.com in 6-month intervals. It was found that tag values do not decrease but grow in terms of quantity and quality. Accordingly, we examined the major significances of the tags and their potential utilization as an expression of subjects. Our findings were as follows. First, the motivations for tagging can be categorized into personal information for search purposes, self-fulfillment such as sense of achievement, display of emotion and sharing of one's experience with others, or an altruistic objective that emphasizes sociality with a desire that one's actions might provide social benefits. According to our analysis, 74.12% of tags had a social motivation. Second, the total number of tags and the frequency of usage increased with time. Third, the categories that showed a high increase in tag usage were dates of publication and reading, key words, main characters, and book reviews. Tags related to subjects had the highest ratio. Fourth, among Library of Congress Subject Headings (LCSH), multiple genres, key words and main characters were assigned to books, and specific key words and other properties were added as time progressed. There was also a slight increase in the number of tags consistent with LCSH. Fifth, we found that key tags could serve as a compilation of terms that reflects the knowledge base of the corresponding era. Thus, folksonomy should be continuously monitored for its quantitative and qualitative development of the tags to make improvements on its formative disadvantages, and identify internal semantic significance, be actively utilized in conjunction with taxonomy as a flexible compilation of terms that incorporate the history of a specific era.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.5
• /
• pp.12-18
• /
• 2008

Ag paste was employed for source and drain electrode of OTFTs and for the data metal lines of OTFT-OLED array on PC(polycarbonate) substrate. We tested two kinds of Ag-pastes such as pastes for 325 mesh and 500 mesh screen mask to examine the pattern ability and electrical performance for OTFTs. The minimum feature size was 60 ${\mu}m$ for 325 mesh screen mask and 40 ${\mu}m$ for 500 mesh screen mask. The conductivity was 60 $m{\Omega}/\square$ for 325 mesh and 133.1 $m{\Omega}/\square$ for 500 mesh. For the OTFT performance the mobility was 0.35 $cm^2/V{\cdot}sec$ and 0.12 $cm^2/V{\cdot}sec$, threshold voltage was -4.7 V and 0.9 V, respectively, and on/off current ratio was ${\sim}10^5$, for both screen masks. We applied the 500 mash Ag paste to OTFT-OLED array because of its good patterning property. The pixel was composed of two OTFTs and one capacitor and one OLED in the area of $2mm{\times}2mm$. The panel successfully worked in active mode operation even though there were a few bad pixels.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.53.2-53.2
• /
• 2010

지금까지 능동 구동 디스플레이의 TFT backplane에 사용하고 있는 채널 물질로는 수소화된 비정질 실리콘(a-Si:H)과 저온 폴리실리콘(low temperature poly-Si)이 대표적이다. 수소화된 비정질 실리콘은 TFT-LCD 제조에 주로 사용되는 물질로 제조 공정이 비교적 간단하고 안정적이며, 생산 비용이 낮고, 소자 간 특성이 균일하여 대면적 디스플레이 제조에 유리하다. 그러나 a-Si:H TFT의 이동도(mobility)가 1 cm2/Vs이하로 낮아 Full HD 이상의 대화면, 고해상도, 고속 동작을 요구하는 UD(ultra definition)급 디스플레이를 개발하는데 있어 한계 상황에 다다르고 있다. 또한 광 누설 전류(photo leakage current)의 발생을 억제하기 위해서 화소의 개구율(aperture ratio)을 감소시켜야하므로 패널의 투과율이 저하되고, 게이트 전극에 지속적으로 바이어스를 인가 시 TFT의 문턱전압(threshold voltage)이 열화되는 문제점을 가지고 있다. 문제점을 극복하기 위한 대안으로 근래 투명 산화물 반도체(transparent oxide semiconductor)가 많은 관심을 얻고 있다. 투명 산화물 반도체는 3 eV 이상의 높은 밴드갭(band-gap)을 가지고 있어 광 흡수도가 낮아 투명하고, 광 누설 전류의 영향이 작아 화소 설계시 유리하다. 최근 다양한 조성의 산화물 반도체들이 TFT 채널 층으로의 적용을 목적으로 활발하게 연구되고 있으며 ZnO, SnO2, In2O3, IGO(indium-gallium oxide), a-ZTO(amorphous zinc-tin-oxide), a-IZO (amorphous indium-zinc oxide), a-IGZO(amorphous indium-galliumzinc oxide) 등이 그 예이다. 이들은 상온 또는 $200^{\circ}C$ 이하의 낮은 온도에서 PLD(pulsed laser deposition)나 스퍼터링(sputtering)과 같은 물리적 기상 증착법(physical vapor deposition)으로 손쉽게 증착이 가능하다. 특히 이중에서도 a-IGZO는 비정질임에도 불구하고 이동도가 $10\;cm2/V{\cdot}s$ 정도로 a-Si:H에 비해 월등히 높은 이동도를 나타낸다. 이와 같이 a-IGZO는 비정질이 가지는 균일한 특성과 양호한 이동도로 인하여 대화면, 고속, 고화질의 평판 디스플레이용 TFT 제작에 적합하고, 뿐만 아니라 공정 온도가 낮은 장점으로 인해 플렉시블 디스플레이(flexible display)의 backplane 소재로서도 연구되고 있다. 본 실험에서는 rf sputtering을 이용하여 증착한 a-IGZO 박막에 대하여 열처리 조건 변화에 따른 a-IGZO 박막들의 광학적, 전기적 특성변화를 살펴보았고, 이와 더불어 a-IGZO 박막을 TFT에 적용하여 소자의 특성을 분석함으로써, 열처리에 따른 Transfer Curve에서의 우리가 요구하는 Threshold Voltage(Vth)의 변화를 관찰하였다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.52-52
• /
• 2012

최근 선진국을 중심으로 제조기술의 산업혁명이라고 불릴 정도로 큰 파급효과가 기대되는 자기조립기반의 산업공정기술을 확보하기 위한 많은 노력과 연구들이 활발하게 진행되고 있다. 자기조립(Self-Assembly) 현상은 자연에서 일어나는 자발적인 힘으로 원자 또는 분자 단위까지 구조물을 제어하고 bottom-up 방식(상향식: 원자/분자 스케일의 나노구조를 배열/조립하여 원하는 형태의 패턴을 만들어 내는 방식)으로 원하는 구조물을 설계/제작할 수 있는 능력을 가지고 있다. 기초적인 과학으로부터 출발한 자기조립기술은 최근 자기조립 응용개발에서 많은 성과를 이루어내면서 산업화 가능성을 크게 하고, 과학계와 산업계의 많은 관심을 불러일으키고 있다. 반도체 산업기술을 예측하는 ITRS 로드맵(2005년)에 의하면 directed self-assembly 방법이 새로운 미래 패터닝 기술로 개발되어 2016년경에 사용되고, 자기조립소재로 제작된 다양한 응용소자들은 새로운 미래소자로 개발될 것으로 예상하고 있다. 이에 맞추어 국내 기업들도 diblock copolymer를 이용한 나노패터닝 기술 확보를 위한 연구를 진행하고 있다. 또한 IBM은 자기조립기술을 반도체공정에 실험적으로 적용하여 자기조립기술이 생산 공정에 부분적으로 적용될 가능성이 크다는 것을 보여주었다. 산업계와 함께 학계의 연구센터에서는 산업화를 위한 자기조립 집적화 공정(Integrated process) 개발을 이루기 위하여 체계적으로 연구를 실시하고 있다. 미국의 Northeastern 대학의 CHN(Center for high-rate Nanomanufacturing) 연구센터는 자기조립 집적화에 용이한 새로운 개념의 소자를 제안하고 이를 집적화하기 위한 다양한 공정을 개발하고 있으며, Wisconsin 대학의 NSEC(Nanosacle Science and Engineering Center) 연구센터는 diblock copolymer를 이용한 나노패터닝 기술 개발에서 획기적인 결과를 도출하여 산업계에 적용될 가능성을 높이고 있다. 이와 같은 결과들로부터 앞으로의 자기조립기술에 대한 연구는 3차원 구조물을 제작할 수 있는 집적화 공정에 집중될 것이고, 이를 위하여 새로운 개념의 단순한 구조의 응용소자개발도 함께 추진될 것으로 판단된다. 또한 실용 가능성이 큰 집적화 공정으로 개발하기 위하여 기존의 top-down 방식을 접목한 bottom-up 방식의 자기조립 집적화 공정이 개발될 것으로 예상하고 있다. 이와 함께 자기조립공정은 반복되는 구조를 쉽게 제작할 수 있는 장점을 가지고 있어 다양한 응용소자 [태양전지(solar cell), 연료전지(fuel cell), 유연성 있는 전자기기(flexible electronics), 화면표시 장치(display device)] 제작에 쉽게 이용되어 새로운 산업을 창출할 수 있는 가능성을 보이고 있다. 본 자기조립 연구 센터에서는 이와 같은 자기조립 특성을 제조공정에 적용하여 혁신적인 제조공정기술을 확보하고자 연구를 진행하고 있다. 그러므로 본 발표에서 이와 같은 연구 흐름과 함께 본 센터에서 진행하고 있는 자기조립 제조방법을 소개하고자 한다. 이와 함께 자기조립방법을 이용하여 제작된 다양한 응용소자 개발 결과를 발표하고, 이를 top-down 방식과 접목하여 집적화공정으로 개발하는 전략을 함께 소개하고자 한다.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.3
• /
• pp.93-97
• /
• 2006

Polymer light emitting diodes (PLEDs) are expected to be commercialized as next generation displays by advantages of the fast response time, low driving voltage and easy manufacturing process for large sized flexible display. Generally, the electrical and optical properties of PLEDs are affected by the surface conditions of transparent electrode. The PLED devices with ITO/PEDOT:PSS/PVK/PFO-poss/LiF/Al structures were prepared by using the spin coating method. For this, PEDOT:PSS(poly(3,4-ethylenedioxythiophene):poly(styrene sulfolnate)) Al 4083 and PVK(N-vinylcabozole) were used as hole injection and transport layers. The PFO-poss(poly(9,9-dioctylfluorene)) was used as the emitting layer. The dependence of $O_2$ plasma treatment of ITO electrode on the electrical and optical properties of PLEDs were investigated. The sheet resistances increased slightly with an improved surface roughness of ITO electrode as the RF power increased during $O_2$ plasma treatment. The PLED devices prepared on the ITO/Glass substrates, which were plasma-treated at 40 watt in RF power for 30 seconds under 40 mtorr $O_2$ pressure, showed the maximum external emission efficiency of 0.86 lm/W and the maximum luminance of $250\;cd/m^2$, respectively. The CIE color coordinates are ranged $X\;=\;0.13{\sim}0.18$ and $Y\;=\;0.10{\sim}0.16$, showing blue color. emission.

• Korean Journal of Optics and Photonics
• /
• v.26 no.1
• /
• pp.23-29
• /
• 2015

In this paper, we propose a microscope system for detecting both a tumor and blood vessels in brain tumor surgery as fluorescence images by using multiple light sources and a beam-splitter module. The proposed method displays fluorescent images of the tumor and blood vessels on the same display device and also provides accurate information about them to the operator. To acquire a fluorescence image, we utilized 5-ALA (5-aminolevulinic acid) for the tumor and ICG (Indocyanine green) for blood vessels, and we used a beam-splitter module combined with a microscope for simultaneous detection of both. The beam-splitter module showed the best performance at 600 nm for 5-ALA and above 800 nm for ICG. The beam-splitter is flexible to enable diverse objective setups and designed to mount a filter easily, so beam-splitter and filter can be changed as needed, and other fluorescent dyes besides 5-ALA and ICG are available. The fluorescent images of the tumor and the blood vessels can be displayed on the same monitor through the beam-splitter module with a CCD camera. For ICG, a CCD that can detect the near-infrared region is needed. This system provides the acquired fluorescent image to an operator in real time, matching it to the original image through a similarity transform.