• Journal of Magnetics
• /
• v.21 no.3
• /
• pp.393-398
• /
• 2016

This paper proposes a novel 16/10 segmented rotor switched reluctance motor (SSRM) for belt-driven starter generators (BSGs). Different from conventional SRMs, the stator of the proposed SSRM consists of two types of stator poles, i.e., exciting and auxiliary poles, and the rotor is constructed from a series of discrete segments. The topology and operation principle of this proposed SSRM are illustrated firstly, and then the design rules are listed. In addition, the finite element method (FEM) is employed to get the static and dynamic characteristics of the proposed SSRM. Finally, the simulation results are presented to show the validity of the proposed SSRM for BSGs.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.134-137
• /
• 2001

In this paper on-line model is derived from investigating via series of finite element process simulation. Some variables that little affect on non-dimensional parameters. ie. forward slip and torque factor. is extracted from composing on-line model Especially, this research focused on deriving on-line model which exactly predict roll force and roll power in the roughing mill process under small shape factor and small reduction ratio. The prediction accuracy of the proposed model is examined through comparison with predictions from a finite element process model

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.125-128
• /
• 2001

A finite element-based, integrated process model is presented for coupled analysis of the thermal and metallurgical behavior of the strip occurring on the run-out-table in hot strip rolling. The validity of the proposed model is examined through comparison with measurements. The models capability of revealing the effect of cooling pattern on strip temperatures and the optimal cooling pattern are demonstrated through a series of process simulation. In order to improve strip shape and control temperature history of thickness direction for strip during ROT cooling.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.4
• /
• pp.941-949
• /
• 1995

An efficient method based on analytic solutions is applied to solve anti-plane Mode III crack problems. The analytic technique developed earlier by the present authors for Laplace's equation in a simply-connected region is now extended to general Mode III crack problems. Unlike typical numerical methods which require fine meshing near crack tips, the present method divides the cracked bodies, typically non-convex or multiply-connected, into only a few super elements. In each super element, an element stiffness matrix, relating the series coefficients of the traction and displacement, is first formed. Then an assembly algorithm similar to that used in the finite elements, is first formed. Then an assembly algorithm similar to that used in the finite elements, is developed. A big advantage of the present method is that only the boundary conditions are to be satisfied in the solution procedure due to the use of analytic solutions. Several numerical results demonstrate the efficiency and accuracy of the present method.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.4
• /
• pp.290-299
• /
• 2003

This paper presents an efficient modeling and dynamic analysis method for open cracked rotor bearing systems. An equivalent bending spring model is introduced to represent the structural weakening effect in the presence of cracks. The proposed modeling method is validated through a series of simulations and experiments. First, the proposed method Is rigorously compared with a commercial finite element code. Then, an experiment is performed to validate the proposed modeling method. Finally, a numerical example is introduced to demonstrate the possible application of the proposed method in the crack diagnosis for rotor systems.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.04a
• /
• pp.155-160
• /
• 1996

The vibration analysis of the automobiles has been a good subject for the engineers seeking solutions for more comfortable life. In the area of industrial vehicles, however, the seriousness of the vibration annoyance has not been considered so much. In this paper, a finite element model was built which was good for the low-frequency system(of fork-lift truck), and a forced vibration analysis was obtained for the component of 2n of harmonic orders from engine excitation to this model. Finally, a design optimization upon dynamic responses was made to minimize the vibration acceleration level at selected points representing the vibration level of the whole system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.42-47
• /
• 2007

An analytical method for the free vibration of a flexible rectangular plate in contact with water is developed by the Rayleigh.Ritz method. The plate clamped along the edges is partially contacted with water at both sides. It is assumed that the water bounded by rigid walls is incompressible and inviscid. The wet mode shape of the plate is assumed as a combination of the dry mode shapes of a clamped beam. The liquid motion is described by using the liquid displacement potential and determined by using the compatibility conditions along the liquid interface with the plate. Minimizing the Rayleigh quotient based on the energy conservation gives an eigenvalue problem. It is found that the theoretical results can predict excellently the fluid.coupled natural frequencies comparing with the finite element analysis result.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.647-651
• /
• 2002

This study dealt with the free vibration of two identical rectangular plates coupled with fluid. In order to investigate the vibration characteristics of fluid-coupled rectangular plates, an analytical method based on the finite Fourier series expansion and Rayleigh-Ritz method was suggested. A commercial computer code, ANSYS was used to perform finite element analysis and we investigated the vibration characteristics with mode shapes and natural frequencies. As a result, the transverse vibration modes, in-phase and out-of-phase, were observed alternately in the fluid-coupled system. The effect of fluid bounding and plate boundary condition on the fluid-coupled natural frequency were investigated. It was shown that the mode numbers increased, the normalized natural frequencies monotonically increased.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.180-183
• /
• 2003

In this research, on-line model for prediction of effective strain distribution hi strip on finishing mill process is prescribed. It has been developed using several selected non-dimensional parameters and previously made average effective strain model via series of finite element process simulations, $\Delta$$\varepsilon$ was introduced to describe the effective strain distribution in strip. To confirm adequate non-dimensional variables uniqueness test was done. And to decide the order of polynomial in on-line model equation tendency test for each variables was done. The prediction accuracy of the proposed model is examined through comparison with finite element calculation results.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.285-290
• /
• 2002

The double composite box girder is a structural system filled with concrete at the bottom of the steel box in the negative moment region increasing the flexural strengths. Flexural strengths of the double composite steel box girders are investigated through a series of the experimental tests and the numerical analysis. The experimental tests are performed on the three kinds of steel box girders with the different concrete depths including loom, 15cm, and 20cm. Moment-curvature relations are calculated based on the sectional analysis method describing the nonlinear natures of concrete and steel. In the finite element analysis the nonlinear nature of concrete is described based on the three dimensional four-parameter constitutive model recently developed and that of steel is described based on von Mises failure criterion. The ultimate flexural capacities of the box girders predicted using sectional analysis and finite element analysis show good agreement with those of the experiments.