• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.639-642
• /
• 1999

Pullout test known as Lok test among the test methods to evaluate concrete strength strength is a test method which is used to decide the form removal time by assessing the early strength of concrete in a new construction, or to control the quality of newly placed concrete. This method has inconvenience to place inserts on the form work in advance, however, the placing work is quite simple and it has advantage that the strength can be measured at field as long as the inserts are placed. In this study, the first step is to investigate the properties of test method itself, by performing the laboratory test which covers deviation of the method and factors affecting the results, etc. The second step is to correlate the result with cylinder strength and other NDT methods such as rebound hammer, ultrasonic method, etc. And that, the results are compared with foreign results to find the differences between the two. In this research, new factors such as moisture content, area of aggregate failure cross section and area of aggregate separation cross section, etc as well as wate-cement ratio and age are investigated.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권1호
• /
• pp.130-137
• /
• 2019

PC구조형식은 사전 제작된 PC 부재를 현장에서 거치한 후 추가 긴장력 도입 및 연결부 시공의 과정을 거쳐서 구조물을 완성시키는 형식이다. 하지만 현장타설부와 PC부 사이 부착면에서 균열발생 및 수밀성 감소에 따른 누수문제가 발생할 수 있다. 이러한 균열 및 누수문제는 철근의 부식을 초래할 수 있으며, 이는 구조물의 장기사용 내구성을 급격히 감소시키는 주요 원인이 될 수 있다. 본 연구에서는 기존 PC 구조물 접합부 경계면에서의 부착력 부족에 대한 문제를 해결하기 위해서, 형상기억합금을 활용한 표면처리 부재를 제안하고, 형상기억합금 와이어를 이용한 연결부의 성능을 평가하고자 하였다. 이를 위해서 본 연구는 해당 기술 실현을 위한 사전연구로서 와이어의 개수와 절곡유무, 그리고 형상기억효과 발현 유무에 따른 연결재의 인발력을 평가하고자 하였다. 연구결과를 통해서 SMA 연결재의 인발저항성능을 결정짓는 연결부의 형상효과와 형상기억발현효과, 그리고 부착효과에 대해서 평가할 수 있었다. 또한 이에 대한 설계변수별 예측식을 제안하였고, 예측값과 실험값 간의 유효성을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제5권4호
• /
• pp.355-368
• /
• 1997

Fiber reinforced plastic (FRP) rods are used as reinforcement (prestressed or not) to concrete. FRP composites can also be combined with steel to form hybrid reinforcing rods that take advantage of the properties of both materials. In order to effectively utilize these rods, their bond behavior with concrete must be understood. The objective of this study is to characterize and model the bond behavior of hybrid FRP rods made with epoxy-impregnated aramid or poly-vinyl alcohol FRP skins directly braided onto a steel core. The model closely examines the split failure of the concrete by quantifying the relationship between slip of the rods resulting transverse stress field in concrete. The model is used to derive coefficients of friction for these rods and, from these, their development length requirements. More testing is needed to confirm this model, but in the interim, it may serve as a design aide, allowing intelligent decisions regarding concrete cover and development length. As such, this model has helped to explain and predict some experimental data from concentric pull-out tests of hybrid FRP rods.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.1107-1112
• /
• 2009

Ground anchor should not be used in soft clay, because anchor resistance can not be guaranteed. However, there is a way to increase the capacity of anchors. The pulse powered anchor is an underreamed anchor by using high voltage electrokinetic pulse energy. In this study, a series of field test were carried out in order to find expansion rate related in number of pulse charge. and Anchor pull-out tests were performed at the Geotechnical Experimentation Site at Sungkyunkwan University in Suwon, Korea. Data were analyzed in order to define a relation between expansion rate and ultimate pullout load.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.320-329
• /
• 2005

The use of diverse methods for the retaining system has been continuously increased in order to maintain the stability during excavation. However, ground anchor system occasionally may have the restriction in urban excavation sites nearby the existing structures because of space limitation. In this case, soil nailing system with relatively short length of nails could be efficiently useful as an alternative method. The general soil nailing support system, however, may result in excessive deformations particularly in excavating the zone of weak soils or nearby the existing structures. Therefore, applying the pretension force to the soil nails then could play important roles to reduce deformations mainly in an upper part of the nailed-soil excavation system as well as to improve the local slope stability. In this study, a newly modified soil nailing technology named as the PSN(Pretention Soil Nailing) is developed to reduce both facing displacements and ground surface settlements during top-down excavation process as well as to increase the global slope stability. Up to now, the PSN system has been investigated mainly focusing on an establishment of the design procedure. In the present study, the field tests including pull-out tests were fulfilled to investigate the behavior of characteristics for PSN system. All results of tests were also analyzed to provide a fundamental and efficient design.

• 산업기술연구
• /
• 제21권B호
• /
• pp.195-203
• /
• 2001

The purpose of this study is to estimate ultimate uplift capacity of permanent anchor which was cast into weathered rock. The ultimate uplift capacity was estimated from the load-displacement curve of four different anchors which have different bond length. The creep test was performed for 15minutes under the maximum load of each step in order to understand the load-transfer property of permanent anchor and to decide which anchor to choose. The destruction range of soil due to the changes in load was estimated by installing dial gauge on the ground which was cast into the weathered rock. Ultimately, the study on the behavior of the anchor case into the weathered rock was performed by comparing and analyzing the estimated result of the UUC obtained by the full scale pull out test in the field with the exsting theoretical and practical results of soil and rock anchor.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.42-50
• /
• 2008

To evaluate rock bolt integrity, destructive test such as pull-out test has been commonly carried out. This method is known as time consuming, expensive, and inaccurate procedure. To improve destructive method, non-destructive techniques using transmitted guided ultrasonic waves were suggested. Note for the transmission method, the source for the generation of ultrasonic waves should be installed during the rock bolt construction. The purpose of this study is to investigate the reflection method using reflected guided ultrasonic waves to evaluate the integrity of the rock bolt grouted, and to compare the results evaluated by the reflection and transmission methods. The guided waves are generated by PZT element and received by AE sensor. The measured signals are analyzed by the wavelet transform. The results show that the energy velocities of guided ultrasonic waves increase with the defect ratio in both transmission and reflection method. The reflection method produces the lower velocity in all defect ratio. This research demonstrates that the reflection method may be suitable and easer method for the field tests.

• 한국건설순환자원학회논문집
• /
• 제10권2호
• /
• pp.168-175
• /
• 2022

최근 나노기술의 발달로 건설재료분야에 이의 적용이 지속적으로 증가하고 있는 실정이다. 하지만 현재까지는 압축강도 50 MPa, 단위중량 16 kN/m³ 정도의 고강도 경량 콘크리트를 구조부재에 적용하기 위한 콘크리트와 철근의 부착 특성에 관한 연구가 부족한 실정이다. 따라서 본 논문에서는 압축강도 50 MPa, 단위중량 16 kN/m³ 정도의 고강도 경량 콘크리트 81개의 시편을 제작하여 직접 인발 부착실험을 수행하였고, 실험결과와 현행 설계기준과 비교하여 부착특성을 평가하였다. ACI-408R의 부착강도 산정식과 실험결과는 비교적 유사한 것으로 판단되며, 통계분석을 통해 CEB-FIP, 수정된 CMR 부착거동 모델을 산정한 결과, 평균적으로 잘 묘사하는 것으로 판단된다.

• Journal of Biosystems Engineering
• /
• 제10권2호
• /
• pp.19-26
• /
• 1985

This study was carried out to develop a versatile data acquisition/processing system for overall tractor performance utilizing a NEC PC-8001 microcomputer. The data acquisition system measures drawbar pull and power, wheel torque and axle power, ground speed, wheel slip, fuel flow, and engine speed. The system stores hexadecimal data for these variables in memory. Upon completion of each test run, all hexadecimal data stored in memory are recorded on floppy disc. The data processing system reads in the data collected on floppy disc and interprete them using several graphical and statistical techniques. The system uses the same microcomputer and a dot-matrix printer. The data acquisition system has been installed on a GOLDSTAR 500 tractor (2WD, 50 ps). A field study has shown that tractor performance data can be quickly and easily collected. It also appeared that the data processing system can be used to efficiently analyze the collected data. The data acquisition system has some troublesome in mounting and handling on tractor since it uses a general-purpose computer consisting of several components.

• 전기학회논문지P
• /
• 제65권2호
• /
• pp.101-107
• /
• 2016

The main target in this paper is the localization of VME Type EPSM in Generator Exciter(EX2100) System. Developed EPSM has the compatibility with the existing product in the structure and shape and electrical feature and so on, but it has a much improved capacity and reliability in comparison with origin company product. this paper, to improve these functions, put emphasis on protection, monitoring, power capacity increase(over 120%), an enlarged scale of input voltage supply, AC/DC dual voltage use and so on. After manufacturing product localization, it was carried out several tests for the performance and reliability verification of developed product. These tests were performed in Authorized Inspection Agency(KTL) and field application test and maker self-test were additionally performed. Finally, the results of all tests were "success".