• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.198-201
• /
• 2004

This paper aims to investigate the micro-mechanical behaviour of tow geometry with forming pressures and densities of foams during the curing process of plain weave carbon fibre fabric prepregs onto polymer foams. In order to find out and compare deformation patterns between different forming conditions, tow parameters such as amplitude and crimp angle etc. are investigated. From the observation results, geometric difference in the tow architecture with respect to forming conditions and foam characteristics were found. To observe the micro-deformation of the fabric structure, appropriate specimens from carbon fibre-foam sandwich structures are sectioned and observed under the microscope.

• 수산해양기술연구
• /
• 제22권1호
• /
• pp.49-57
• /
• 1986

The vibrations problem of thin orthotropic skew plates of linearly varying thickness is analyzed using the small deflection theory of plates. Using dimensionless oblique coordinates, the deflection surface can be expressed as a polyonmial series satisfying the boundary conditions. For orthotropic plates which is clamped on all the four edges, numerical results for the first two natural frequencies are presented for various combinations of aspect ratio, skew angle and taper parameter. The properties of material used are one directional glass fibre reinforced plastic GFRP. The results obtained may be summarised as follows: 1. In case of the first mode vibration of plates with increase in the skew angle, the natural frequencies of plates decrease. 2. As the aspect ratio decrease, the natural frequencies of plates decrease. 3. For the identical skew angle, natural frequencies of plates increase with the taper parameter of thickness.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 춘계학술발표대회 논문집
• /
• pp.211-214
• /
• 2003

This paper presents the microscopic observation results from the picture frame test using five-harness satin weave fabric composite. Aligned and misaligned specimens are observed to verify the exact tow deformation pattern such as tow interval and change in tow amplitude. To observe the micro-deformation of the fabric structure, appropriate specimens from picture frame test are sectioned and observed under the microscope. From the observation results, it is found that a picture frame test with a misaligned fibre orientation angle shows large differences in deformation between tensile and compressive tow directions.

• 한국강구조학회 논문집
• /
• 제10권2호통권35호
• /
• pp.201-209
• /
• 1998

강섬유보강 적층복합구조물에서 온도의 변화는 구조물의 응답에 중요한 영향을 미칠수 있다. 온도의 급작스런 변화는 재료의 강도와 성질을 현저히 저하시켜 구조물의 대변형, 좌굴, 고응력상태를 유발하는 중요한 인자가 된다. 본 연구에서는 등분포로 재하된 온도하중에 의한 적층복합판의 온도좌굴에 관한 해석을 수행하였다. 전단변형의 효과를 정확히 고려하기위해 5개의 변수로 구성된 고차전단변형이론을 적용하였다. 적층판의 배열각도, 적층판의 수, 폭-두께비의 변화, 형상비의 변화에 따른 임계좌굴온도를 구하여 1차전단변형이론에 의한 결과와 고전적이론에 의한 결과와 비교분석하였다.

• Steel and Composite Structures
• /
• 제14권2호
• /
• pp.121-132
• /
• 2013

This paper deals with multiobjective optimization of symmetrically laminated composite angle-ply annular sector plates subjected to axial uniform pressure load and thermal load. The design objective is the maximization of the weighted sum of the critical buckling load and fundamental frequency. The design variable is the fibre orientations in the layers. The performance index is formulated as the weighted sum of individual objectives in order to obtain the optimum solutions of the design problem. The first-order shear deformation theory is used for the mathematical formulation. Finally, the effects of different weighting factors, annularity, sector angle and boundary conditions on the optimal design are investigated and the results are compared.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.161-162
• /
• 2020

In this study, as part of securing related data, water droplets were dropped on the upper part of the wooden board for flooring in an environment such as floor heating, and the degree of absorption according to the surface temperature change was tested. The test results showed that the contact angle of the surface was low (25℃→40℃) or the droplet was absorbed into the small plate and disappeared. The contact angle of the OSB and MDF was decreased within 30 minutes, but the surface water droplet was maintained longer than the plywood. This is because the surface is coated with hydrophobicity unlike the plywood, but moisture absorption in the cross section after the second processing will not be prevented and it will lead to defect occurrence problem.

• Composites Research
• /
• 제17권1호
• /
• pp.38-46
• /
• 2004

본 논문의 목적은 탄소섬유 건직물의 토우 구조의 미소 거동과 변형 중의 평면 하중과의 관계를 규명하는 것이다. 평면 하중은 변형 중에 토우들을 재배치하며, 결국에는 잠김 현상을 유발하게 된다. 본 논문에서는 토우 간격, 주름각등의 미소 변형 변수들을 관찰하기 위해 일방향 편향 인장실험과 이축 인장실험을 겪은 시편들을 전단각에 따라 분류하여 현미경을 이용하여 변형 경향을 관찰하였다. 전단각에 따른 변형된 토우 구조의 변화를 간단한 설계 변수 모델을 이용하여 근사하였다.

• Structural Engineering and Mechanics
• /
• 제75권1호
• /
• pp.123-131
• /
• 2020

The bond performance of glass fibre reinforced polymer (GFRP) bars and that of steel bars embedded in Alkali Activated Cement (AAC) concrete are analysed and compared using pull-out specimens. The bond failure modes, the average bond strength and the free end bond stress-slip curves are used for comparison. Tepfers' concrete ring model is used to further analyse the splitting failure in ribbed steel bar and GFRP bar specimens. The angle the bond forces make with the bar axis was calculated and used for comparing bond behaviour of ribbed steel bar and GFRP bars in AAC concrete. The results showed that bond failure mode plays a significant role in the comparison of the average bond stress of the specimens at failure. In case of pull-out failure mode, specimens with ribbed steel bars showed a higher bond strength while specimens with GFRP bars showed a higher bond stress in case of splitting failure mode. Comparison of the bond stress-slip curves of ribbed steel bars and GFRP bars depicted that the constant bond stress region at the peak is much smaller in case of GFRP bars than ribbed steel bars indicating a basic bond mechanism difference in GFRP and ribbed steel bars.

• Steel and Composite Structures
• /
• 제33권5호
• /
• pp.663-679
• /
• 2019

In this work, a simple four-variable trigonometric shear deformation model with undetermined integral terms to consider the influences of transverse shear deformation is applied for the dynamic analysis of anti-symmetric laminated composite and soft core sandwich plates. Unlike the existing higher order theories, the current one contains only four unknowns. The equations of motion are obtained using the principle of virtual work. The analytical solution is determined by solving the eigenvalue problem. The influences of geometric ratio, modular ratio and fibre angle are critically evaluated for different problems of laminated composite and sandwich plates. The eigenfrequencies obtained using the current theory are verified by comparing the results with those of other theories and with the exact elasticity solution, if any.

• 한국문화재보존과학회:학술대회논문집
• /
• 한국문화재보존과학회 2006년도 제24회 학술대회발표 논문집
• /
• pp.11-15
• /
• 2006

This work aims to clarify the character and selection of repair papers, based on fibre orientation information of paper cultural properties under restoration; using nondestructive image analysis applied to micrographs of paper surfaces. Image analysis using fast Fourier transform with suitable modifications was demonstrated to be an effective means to determine angle and intensity of fiber orientation as a nondestructive method. In the case of contemporary repair papers, the Japanese handmade paper exhibited a high anisotropy value, while the Korean handmade papers exhibited low anisotropy values. Korea and Japanese traditional hand making papers were well distinguished. Korea and Japanese papers made in the traditional ways showed its own characteristic orientation behavior in accordance with the motion of a bamboo wire.