• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.5
• /
• pp.135-142
• /
• 2022

In this study, lap spliced ultra-high strength reinforced concrete beams were tested and the code criteria for calculating the lap splice length which was affected by the transverse reinforcement and concrete covering performance were reviewed. The main variables for test were set as fiber volume fraction and transverse reinforcing bar arrangement to improve the confining performance of the concrete cover. The change of the confining performance of concrete cover according to the increase in the fiber mixing amount at 1% and 2% volume ratio was examined, and D10 stirrups with a spacing of 100 mm were placed in the lap spliced region. As a result of the test, the specimens confined by the stirrups showed a sudden drop of load bearing capacity with horizontal cracking at the position of tensile longitudinal reinforcement. However, horizontal cracks were not appeared at the location of longitudinal reinforcement for the specimens with steel fiber. And these specimens showed gradual decrease of load bearing capacity after experiencing peak load. In particular, it was found that the strain at the position of the tensile longitudinal reinforcements of the specimens to which the mixing ratio of 2% was applied exceeds the yield strain. As a result of measuring the strain on the concrete surface, it was found that the fiber was more effective in preventing damage to the concrete surface than the stirrups for short lap spliced region.

• Food Science and Biotechnology
• /
• v.17 no.2
• /
• pp.241-246
• /
• 2008

A nutritional supplement was developed aiming at correcting the most common nutrient and caloric deficiencies encountered in elderly people (${\geq}60$ years old). The protein source was a mixture of whey protein isolates (WPI) and bovine collagen hydrolysate (BCH) with high nutritional and functional qualities making up 12% of the formulation. The carbohydrate fraction was composed of sucrose, inulin (soluble fiber), and fructo-oligosaccharide (prebiotic). The most commonly deficient essential minerals and vitamins were also included. Acceptance of the product was good according to both an elderly panel and a laboratory panel composing of both sexes and various ages. The stability of the formulations was evaluated and the estimated shelf life at room temperature (ca. $27^{\circ}C$) was approximately 4 months.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.27-32
• /
• 2008

The laminated composite materials have been applied to various mechanical structures due to their high performance to weight ratios. In this study, we suggest a stochastic finite element scheme for the probabilistic analysis of the composite laminated plates. The composite materials consist of two different materials which constitute the matrix and fiber. The material properties in the major and minor directions are determined depending on the volume fraction of these two materials. In this study, the elastic modulus and shear modulus are considered as random and the effect of these random properties on the behavior of the composite plate is investigated. We adopt the weighted integral scheme in the formulation, which has been recognized as the most accurate method in the statistical methodologies. For verification of the proposed scheme, Monte Carlo analysis is also performed for the comparison with the proposed scheme.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.3
• /
• pp.588-594
• /
• 1998

Reliable three-dimensional models of woven fabric composites had scarcely been proposed for their geometric complexity. Simplified models, mostly one- or two-dimensional, currently used are not considered effective enough because of their oversimplifications. In this paper, the equivalent thermal conductivities and elasticity properties of woven fabric composites are computed using homogenization technique. The computational results show that the strength and thermal conductivity linearly increase with fiber volume fraction and that the variations of undulation of fibers has little effect on equivalent material properties. Homogenization technique is proved useful in the study of woven fabric composites and may find a lot more applications in the area.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.04a
• /
• pp.15-19
• /
• 2000

Recently Western countries are now beginning to use ACM (Advanced Composites Material), in the construction industry Compared with existing construction materials, ACM possesses many advantages such as light-weight, high-strength, corrosion resistant property. Among other fabrication process of ACM, pultrusion is one of the promising one for civil infrastructure application. In this paper, the structural characteristics of pultruded GFRP strip and structural members of angle and tube type were studied. For the strip, parametric studies of pultrusion process has been carried out. Considered parameters were volume fraction, temperature, pulling speed and fiber orientations. For the pultruded angle and tube, compression test and buckling analysis has been carried out. The results were compared with calculated values using coded formulae

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.184-188
• /
• 2001

The squeeze infiltration process is potentially of considerable industrial importance. The performance enhancements resulting from incorporation of short alumina fiber into aluminum are well documented. These are particularly significant for certain automobile components. But the solidification process gets complicated with manufacturing parameters and factors for porosity formation do not fully understand yet. In this study porosity defects were observed under several infiltrating conditions ; a kind of matrix, an initial temperature of melt, and a volume fraction of reinforcement. The desimetry and the microscopic image analysis were done to measure the amount of porosity. A correlation between manufacturing parameters and defects was investigated through these.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.73-76
• /
• 2002

This study developed SiC/Al composites for electronic packaging to which reinforcements were added with the volume fractions of 49%, 56% and 63% by the squeeze casting method. 0.8 wt.% of the inorganic binder as well as the $Al_2O_3$ fiber and SiC particles with the volume fraction of 1:10 were added to the SiC/Al composites For the produced SiC/Al composites, the CTEs (coefficients of thermal expansion) were measured from 30 to $300^{\circ}C$ and compared with the FEM numerical simulation to analyze the temperature dependent properties. The experiment showed the CTEs of SiC/Al composites that were intermediate values of those of Rule of Mixture and Turner's Model. The CTEs were close to Turner's Model in the room temperature and approached the Rule of Mixture as the temperature increases. These properties analyzed from the difference of the average stress acting between the matrix and the reinforcements proposed in this study

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04b
• /
• pp.541-546
• /
• 1998

The use of steel fibers in conventional reinforced concrete increases the strength and ductility under various loading conditions. In order to examine the possibility of the use of these combinations achieving required strength and ductility of a reinforced concrete beam, a refined optimization procedure based on nonlinear layered finite element method and nonlinear programming technique is developed in this study. Six design variables-beam width and depth, fiber volume fraction, amounts of tensile and compressive rebars, and stirrup, and stirrup spacing-are considered. The developed model can be used as a tool in determining the economical use of steel fibers in designing the reinforced steel fibrous concrete beam.

• Textile Coloration and Finishing
• /
• v.17 no.1
• /
• pp.38-44
• /
• 2005

Oxidation method was used to extract S-keratose from wool. Wool was treated with performic acid and soluble fraction(S-keratose) was collected by evaporating the solvent. S-keratose and Nylon 6 were dissolved in formic acid at the ratio of 100/0, 80/20, 50/50, 20/80, and 0/100, and S-keratose/Nylon 6 web of sub-micron size was made by electro-spinning technique. SEM, EA, FT-IR, XRD, and TGA were used to characterize the properties of S-keratose/Nylon 6 solutions and electrospun fibers. As the Nylon 6 content increased, viscosity, conductivity of the electrospinning solution and the diameter of spun fiber increased. Electrospun nonwoven webs have the same S-keratose/Nylon 6 ratios of the spinning solutions. The crystalline structures of S-keratose and Nylon 6 existed separately in the electrospun webs. Thermal stability of the webs increased due to Nylon 6 content.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.311-318
• /
• 1995

Increases in strength and ductilities of steel fiber reinforced concrete(SFRC) under direct tension and compression result in improvements of flexural behavior of reinforced steel fibrous concrete beam(RSFCB) Use of hooked steel fibers in stead of round steel fibers enhances futher the structural porperties of a beam due to their greater mechanical bond resistance compared to that of round steel fibers. Flexural strength, initial stiffness ductility and failure mechani는 of RSFCB are dependent upon material and structural parameters and among which are the volume fraction of fibers, reinforcement ratio, and casting depth of SFRC in a beam section. The flexural behavior of RSFCB's are examined experimentally in this study and some conclusions are made regarding those effects of main material and structural parameters on the overall behavior of RSFCB.