• Macromolecular Research
• /
• 제15권1호
• /
• pp.86-89
• /
• 2007

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.362-363
• /
• 2006

In this study, the filter was designed for tuning center frequency and fabricated using ($Sr,Ba)TiO_3$ ferroelectrics and $YBa_2CuO_7$ high temperature superconductor thin film. The best result in figure of merit was 35 when the $Ba_{0.5}Sr_{0.5}TiO_3$ thin film deposition temperature was $600^{\circ}C$, the post anneal condition was $600^{\circ}C$, 10min in 1atm, $O_2$. When using $20{\mu}m$ IDC pattern gap. The higher tunability was obtained than using $30{\mu}m$ pattern gap.

• 한국재료학회지
• /
• 제13권5호
• /
• pp.317-322
• /
• 2003

Bismuth layered structure ferroelectric thin films, $Bi_4$$Ti_3$$O_{12}$ / (BTO) and Nb-doped BTO (BTN) were prepared on the Pt(111)/Ti/$SiO_2$/Si(100) substrates by a sol-gel route. We investigated the Nb-doping effect on the grain orientation and ferroelectric properties. $Nb^{5＋}$ ion substitution for $Ti^{4＋}$ ion in perovskite layers of BTO decreased the degree of c-axis orientation and increased the remanent polarization (2Pr). The fatigue resistance of Nb-doped BTO thin film was shown to be superior to that of BTO, and the leakage current of Nb-doped BTO thin film was decreased about 1 order of magnitude compared with BTO. The improvement of ferroelectric properties with $Nb^{5＋}$ doping in BTO could be attributed to the changes in space charge densities and grain orientation in the thin film.

• 한국재료학회지
• /
• 제17권7호
• /
• pp.386-389
• /
• 2007

The dielectric properties of $(Ba_{0.5}Sr_{0.5})TiO_3$ ferroelectric thin films have been investigated according to the substrates in order to optimize the their properties. MgO, r-plane sapphire, and poly-crystalline sapphire (Alumina) substrates have been used to deposite $(Ba_{0.5}Sr_{0.5})TiO_3$ ferroelectric thin films by RF magnetron sputtering. The BST thin films deposited on the single crystal (100)MgO substrates have high tunability and low dielectric loss. These results are caused by a low misfit between the lattice parameters of the BST films and the substrate. The BST films deposited on r-plane sapphire have relatively high misfit, and the tunability of 17% and dielectric loss of 0.0007. To improve the dielectric properties of the BST films, the post-annealing methods has been introduced. The BST films deposited on (100)MgO, (1102)r-plane sapphire, and poly-crystalline sapphire substrates have best properties in post-annealing conditions of $1050^{\circ}C$, $1100^{\circ}C$, and $1150^{\circ}C$, respectively. The different optimal post-annealing conditions have been found according to the different misfits between the films and substrates, and thermal expansion coefficients. Moreover, the films deposited on alumina substrate which is relatively cheap have a good tunability properties of 23% by the post-annealing.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.305-309
• /
• 2002

We have successfully fabricated a Metal-Ferroelectric-Insulator-Semiconductor (MFIS) structure using Bi$\sub$4-x/La$\sub$x/Ti$_3$O$\sub$12/ (BLT) ferroelectric thin film and SiO$_2$/Nitride/SiO$_2$ (ONO) stacked buffer layers for single transistor type ferroelectric nonvolatile memory applications. BLT films were deposited on 15 nm-thick ONO buffer layer by sol-gel spin-coating. The dielectric constant and the leakage current density of prepared ONO film were measured to be 5.6 and 1.0 x 10$\^$-8/ A/$\textrm{cm}^2$ at 2MV/cm, respectively, It was interesting to note that the crystallographic orientations of BLT thin films were strongly effected by pre-bake temperatures. X-ray diffraction patterns showed that (117) crystallites were mainly detected in the BLT film if pre-baked below 400$^{\circ}C$. Whereas, for the films pre-baked above 500$^{\circ}C$, the crystallites with preferred c-axis orientation were mainly detected. From the C-V measurement of the MFIS capacitor with c-axis oriented BLT films, the memory window of 0.6 V was obtained at a voltage sweep of ${\pm}$8 V, which evidently reflects the ferroelectric memory effect of a BLT/ONO/Si structure.

• Journal of information and communication convergence engineering
• /
• 제2권2호
• /
• pp.93-96
• /
• 2004

The a-Si:H TFT using ferroelectric of $SrTiO_3$ as a gate insulator is fabricated on glass. Dielectric characteristics of ferroelectric are superior to $SiO_2$ and $Si_{3}N_{4}$. Ferroelectric increases on-current, decreases threshold voltage of TFT and also improves breakdown characteristics. The a-SiN:H has optical band gap of 2.61 eV, retractive index of 1.8∼2.0 and resistivity of $10^{13}$~$10^{15}$ $\Omega$cm, respectively. Insulating characteristics of ferroelectrics are excellent because dielectric constant of ferroelectric is about 60∼100 and breakdown strength is over 1MV/cm. TFT using ferroelectric has channel length of 8∼20 $\mu\textrm{m}$ and channel width of 80∼200 $\mu\textrm{m}$. And it shows that drain current is 3.4$\mu\textrm{A}$ at 20 gate voltage, $I_{on}$/$I_{off}$ is a ratio of $10^5$~$10^8$ and $V_{th}$ is 4∼5 volts, respectively. In the case of TFT without ferroelectric, it indicates that the drain current is 1.5 $\mu\textrm{A}$ at 20 gate voltage and $V_{th}$ is 5∼6 volts. With the improvement of the ferroelectric thin film properties, the performance of TFT using this ferroelectric has advanced as a gate insulator fabrication technology is realized.

• 한국세라믹학회지
• /
• 제33권6호
• /
• pp.623-630
• /
• 1996

A Sol-gel derived ferroelectric PbTiO3 thin film was synthesized by using diethanolamine (DEA) as a comple-xing agent. Surface chemical analyses were examined in order to study the effect of heating temperature on the composition of thin film by EPMA and XPS. A rapid volatilization of lead was observed in the films fired at $700^{\circ}C$ or higher and the ratio of Pb:Ti was found to be 34:66. A depth profile by Ar+ showed that the Ar sputtering decreased Pb amount of inner part of the film resulting in Ti-rich phase near the surface of the film.

• 한국정보통신학회논문지
• /
• 제11권9호
• /
• pp.1717-1723
• /
• 2007

본 연구에서는 PLZT(10/30/70), PLT(10), PZT(30/70) 강유전체 박막을 이용한 quasi-MFISFET (Metal-Ferroelectric-Insulator-Semiconductor FET) 소자를 제작하여 드레인 전류 특성을 조사하였다. 이로부터, quasi-MHSFET 소자의 드레인 전류 크기가 강유전체 박막의 분극 크기에 따라 직접적인 영향을 받으며 결정된다는 사실을 알 수 있었다. 또, ${\pm}5V$ 와 ${\pm}10V$의 게이트 전압변화를 주었을 때 메모리 윈도우는 각각 0.5V 와 1.3V 이었고, 강유전체 박막에 인가되는 전압에 의해 만들어지는 항전압의 변동에 따라 메모리 윈도우가 변화된다는 사실을 확인할 수 있었다. MFISFET 소자의 retention 특성을 알아보기 위 해 PLZT(10/30/70) 박막의 전기장과 시간지연에 따른 누설전류 특성을 측정하여 전류밀도 상수 $J_{ETO}$, 전기장 의존 요소 K, 시간 의존 요소 m을 구하고, 이들 파라미터를 이용하여 시간에 따른 전하밀도의 변화를 정량적으로 분석하였다.

• 한국세라믹학회지
• /
• 제32권7호
• /
• pp.783-792
• /
• 1995

Sol-Gel derived ferroelectric PZT thin films were fabricated on ITO/Glass and Si/SiO2 substrates. In order to investigate the effect of catalysts on the densification and crystallization of PZT thin films, a nitric acid or ammonium hydroxide was added to the PZT stock solution at the state of partial hydrolysis reaction. The measured pH for a stable PZT sol was 5.2~9.3. In case of an acid-catalyzed PZT sol, a highly condensed particulate PZT sol was formed by accelerating the hydrolysis reaction. But weakly branched polymeric PZT sol was formed with a base-catalyzed condition. The difference in densification behavior was not found in the pH range of added catalyst, but the refractive index of PZT thin film was increased rapidly as the annealing temperature increased. The PZT thin film annealed at 54$0^{\circ}C$ for 10 min was fully densified and its refractive index was above 2.4. When the annealing temperature increased, the transition from the pyrochlore phase to perovskite appeared at 54$0^{\circ}C$. The base-catalyzed PZT thin film suppressed to form the pyrochlore phase and proceeded effectively to convert the perovskite phase. This was due to the formation of polymeric molecular structure by controlling the hydrolysis and condensation reaction through the additiion of the ammonium hydroxide.

• 한국세라믹학회지
• /
• 제33권6호
• /
• pp.665-671
• /
• 1996

Ferroelectric Pb(Fe1/2Nb1/2)O3 thin films were successfully fabricated on ITO/Glass substrate by sol-gel proces-sing and characterized to determine the dielectric and electric properties. Viscosity of PEN sol measured to investigate rheological properties was 3.25 cP which was proper for coating. The sol also showed Newtonian behavior. RTA(Rapid Thermal Annealing) was used for the annealing of the thin film and 1200~1700$\AA$ thick PEN thin films were fabricated by repeating the intermediate and the final annealing. After the deposition of Pt as top electrode by vacuum evaporation dielectric and electric properties were measured. Dielectric properties of FFN thin film were enhanced by increasing the perovskite phase fraction with increasing the annealing temperature. Measured dielectric constant of 1700$\AA$ PFN thin film annealed at $650^{\circ}C$ was 890 at 1kHz Capacitatnce density and dielectric loss were 47 fF/${\mu}{\textrm}{m}$2 and 0.47 respectively. As a result of measuring Curie temperature PFN thin films had Curie point with a rang of 110~12$0^{\circ}C$ and showed broad dielectric peak at that point. Leakage current of the PFN thin films were increased with increasing the annealing tempera-ture.