• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.871-878
• /
• 2018

In this paper, the conducted EMI reduction performances of active feed-forward current-sensing current-actuation (CSCA) and voltage-sensing current-actuation (VSCA) filters for a three-phase induction motor drive system are evaluated by experiments. For comparison purposes, the conducted EMI (CM emission, DM emission and total emission) of a three-phase induction motor drive with a conventional CM choke, a conventional CM choke in series with an active VSCA filter, and an active CSCA filter (where the CM choke was modified and used as a sensing current transformer) were compared to the case of a system without any filter inserted. Experimental results show that the active CSCA and VSCA filters can improve the CM reduction performance of the conventional CM choke by about 5 dB especially at low-frequencies. However, for DM comparisons, it shows that there is no different between cases with and without filters inserted.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.4
• /
• pp.93-100
• /
• 2002

The current from the feed motor of a machine tool contains substantial information about the machining state. There have been many researches that investigated the current as a measure for the cutting farces. However it has been reported that this indirect measurement of the cutting farces from the feed motor current is only feasible in low frequency. In this research, it was presented that the bandwidth of the current monitoring can be expanded to 130 Hz. And the unusual behavior of the current was examined in this bandwidth. The cross-feed directional cutting force influences the machined surface of the workpiece, which makes it necessary to estimate this force to control the roughness of the machined sulfate. The current exists in the stationary feed motor, and it can give the useful information on the quality of the machined surface. But the unpredictable behavior of the current prevents applying the current to prediction of the cutting state. Empirical approach was conducted to resolve the problem. As a result, the current was shown to be related to the accumulation of the accumulation of the infinitesimal rotation of the motor. rotation of the motor. Subsequently the relationship between the current and the cutting force was identified.

• Journal of information and communication convergence engineering
• /
• v.6 no.2
• /
• pp.154-157
• /
• 2008

A class-E RF(Radio Frequency) power amplifier for wireless application is designed using standard CMOS technology. To drive the class-E power amplifier, a class-F RF power amplifier is used and the reliability characteristics are studied with a class-E load network. The reliability characteristic is improved when a finite-DC feed inductor is used instead of an RF choke with the load. After one year of operating, when the load is an RF choke the output current and voltage of the power amplifier decrease about 17% compared to initial values. But when the load is a finite DC-feed inductor the output current and voltage decrease 9.7%. The S-parameter such as input reflection coefficient(S11) and the forward transmission scattering parameter(S21) is simulated with the stress time. In a finite DC-feed inductor the characteristics of S-parameter are changed slightly compared to an RF-choke inductor. From the simulation results, the class-E power amplifier with a finite DC-feed inductor shows superior reliability characteristics compared to power amplifier using an RF choke.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.994-1003
• /
• 2016

Two major obstacles in the utilization of electrical vehicles are their price and range. The collaboration of direct torque control (DTC) with induction motor (IM) is preferred for its low cost, easy implementation, and parameter independency. However, in terms of edges, the method has drawbacks, such as variable switching frequency and undesired current harmonic distortion. These drawbacks result in acoustic noise, reduced efficiency, and electromagnetic interference. A feed-forward approach for stator-flux-oriented DTC with space vector pulse-width modulation is presented in in this paper. The outcome of the proposed method is low current harmonic distortion with fixed switching frequency while preserving the torque performance and simple application feature of basic DTC. The method is applicable to existing and forthcoming IM drive systems via software adaptation. The validity of the proposed method is confirmed by simulation and experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.135-136
• /
• 2010

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.5
• /
• pp.62-70
• /
• 2007

In this paper, the boost Power Factor Correction(PFC) technique for Direct Torque Control(DTC) of brushless DC motor drive in the constant torque region is implemented on a TMS320F2812DSP. Unlike conventional six-step PWM current control, by properly selecting the inverter voltage space vectors of the two-phase conduction mode from a simple look-up table at a predefined sampling time, the desired quasi-square wave current is obtained, therefore a much faster torque response is achieved compared to conventional current control. Furthermore, to eliminate the low-frequency torque oscillations caused by the non-ideal trapezoidal shape of the actual back-EMF waveform of the BLDC motor, a pre-stored back-EMF versus position look-up table is designed. The duty cycle of the boost converter is determined by a control algorithm based on the input voltage, output voltage which is the dc-link of the BLDC motor drive, and inductor current using average current control method with input voltage feed-forward compensation during each sampling period of the drive system. With the emergence of high-speed digital signal processors(DSPs), both PFC and simple DTC algorithms can be executed during a single sampling period of the BLDC motor drive. In the proposed method, since no PWM algorithm is required for DTC or BLDC motor drive, only one PWM output for the boost converter with 80 kHz switching frequency is used in a TMS320F2812 DSP. The validity and effectiveness of the proposed DTC of BLDC motor drive scheme with PFC are verified through the experimental results. The test results verify that the proposed PFC for DTC of BLDC motor drive improves power factor considerably from 0.77 to as close as 0.9997 with and without load conditions.

• Asian-Australasian Journal of Animal Sciences
• /
• v.16 no.2
• /
• pp.234-238
• /
• 2003

This experiment was conducted to measure nutrient digestibility and performance in broiler chicks fed diets based on normal and low viscosity rye or barley fed with and without enzyme (pentosanase and $\beta$-glucanase) during a 17 day growth trial. A total of 150 one-day old, male broiler chicks (5 birds per pen and 5 pens per treatment) were randomly assigned to one of six dietary treatments in a $3{\times}3$ factorial design experiment (3 cereals${\times}$2 enzyme levels). Digestibility coefficients were determined using chromic oxide. Digestibility coefficients for dry matter and crude protein were significantly (p=0.0001) higher for the barley-based diets than for any of the rye-based diets. Digestibility coefficients for gross energy did not differ (p>0.05) due to cereal grain. There were no differences in the digestibility coefficients for dry matter and gross energy between chicks fed normal and low viscosity rye. However, the digestibility coefficient for crude protein was higher (p=0.01) for the low viscosity rye compared with the normal viscosity rye. Addition of enzyme to the diet significantly (p=0.0001) increased digestibility coefficients for dry matter, crude protein and energy. There were no significant differences in weight gain, feed intake or feed conversion between birds fed barley or rye or between birds fed normal or low viscosity rye. Enzyme supplementation significantly improved (p=0.0001) weight gain, intake and feed conversion. The overall results of this experiment indicate that unsupplemented barley and rye do not support adequate growth rates in poultry. Enzyme supplementation dramatically improved broiler performance. In addition, genetic selection to reduce the viscosity of rye had only a modest effect on the nutritive value of rye for broilers.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.38-43
• /
• 1994

In milling process, monitoring and diagosis system is very importent to accomplish factory automation. In this study, to drvelope on-line tool breakage detection system in face milling operation, analysis and experiment were performed. The tool breakage detection experiment was performed in machining center and the effectiveness of the detection tool breakage detection alorithm and the usage of feed drive current as a detection signal were verified.

• Journal of Power Electronics
• /
• v.12 no.2
• /
• pp.276-284
• /
• 2012

AC/AC power conversion is widely used to feed AC loads with a variable voltage and/or a variable frequency from a constant voltage constant frequency power grid or to connect critical loads to an unreliable power supply while delivering a very balanced and accurate sinusoidal voltage system of constant amplitude and frequency. The load specifications will clearly impose the requirements for the inverter stage of the power converter, while wider ranges of choices are available for the rectifier. This paper investigates the utilization of a buck-type current source rectifier as the active front-end stage of an AC/AC converter for applications that require an adjustable DC-link voltage as well as elimination of the low-frequency common mode voltage. The proposed solution is to utilize a combination of two or more zero current vectors in the Space Vector Modulation (SVM) technique for Current Sources Rectifiers (CSR).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.595-598
• /
• 2000

This paper presents new cutting force measuring system for milling process. Usually, tool dynamometer is the most appropriate measuring tool in an analysis of cutting mechanism. High price and limited space, however, make it difficult to be in-situ system for controllable milling process. Although an alternative using AC current of servomotor has been suggested, it is unsuitable for cutting force control because of low bandwidth and noise. We suggest new cutting force measuring system, using two load cell placed between moving table and nut of ballscrew, and modelled on the system statically and dynamically. And to verify the accuracy of the proposed system, a series of carefully conducted experiments were carried out. Experiment results show that models are in reasonably good agreement with the experiment data.