• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.5
• /
• pp.339-345
• /
• 1987

In the region of high temperature, a very appreciable short-circuit current Is was observed from M1(A1)-P(PET)-M2(Cu) system sandwitched with hetero metals without applying external field. The short-circuit current Is is greatly dependent on electrode material and it has been certified by measuring open-circuit voltage. From these experimental results, we can see that Is is due to electro-chemical action in M-P interface. In this electro-chemical reaction,the generation reaction and the solution reacftion of the oxidies from electrode are probably co-exist and the measured values of the open-circuit voltage was almost correspond to those calculated from Nernst equation.

• Journal of Korea Society of Industrial Information Systems
• /
• v.12 no.2
• /
• pp.79-84
• /
• 2007

This papar reports design and fabrication of CMOS temperature control circuit using MOSIS 0.25um-3.3V CMOS technology. The proposed circuit has a temperature coefficient of $13mV/^{\circ}C$ for a wide operating temperature range with a good linearity. Furthermore, the temperature coefficient of output voltage can be controlled by adjusting external bias voltage. This circuit my be applicable to the design of one-chip IC where quartz crystal resonator is mounted on CMOS oscillator chips.

• 전기의세계
• /
• v.21 no.1
• /
• pp.7-12
• /
• 1972

General steady state equivalent circuits are derived for the family of single phase motor having two windings with non-quadrature. First, the fundamental voltage equations of motor are derived by Faraday-Krichhoff's low in the fiew of the flux distribution in the modified motor with Kron primitive machine. Those equations are arranged in to f-b equations by transformation matrix. To using the above equations for circuit; 1) The concept of current-source was much help to sove the realtions between matrix impedance equation and circuit analysis 2) The simplification of the circuit to the mutual impedance matrix elements is easy to considerations of motor characteristics in the case of inserted external auxiliary winding impedance. Finally, this equivalent circuit showing as a single phase induction motor with quadrature winding is described by each conditions.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.12
• /
• pp.37-42
• /
• 1997

A new temperature and supply-insensitive CMOS current reference circuit was designed and tested. Te temperature insensuitivity was achieved by eliminating the mobility dependence term through the multiplication of two current components, one which is proportional to mobility and the other which is inversely proportional to mobility, by using a newly designed CMOS square root circuit. The CMOS sqare root circuit was derived from its bipolar counterpart by operating the MOS transistors in the subthreshold region. The supply insensitivity was achieved by using an internal voltage generator. Te test chip was designed ans sent out for fabrication by using a 2.mu.m double-poly double-metal n-well CMOS technology. When an external voltage source was used for the square root circuit, the maximum variation and the average temperature sensitivity were measured to be 3% and 21.4ppm/.deg.C, respectively, for the temperature range of -15~130.deg.C. The maximum current variation with supply voltage was measured to be 3% within the commerical supply voltage range of 4.5~5.5V at 30.deg. C.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.1
• /
• pp.21-26
• /
• 2018

In this paper, a multiple coupling inductor with expandable-integrated magnetic structure was proposed to enable miniaturization of external switched mode power supply (SMPS) for a large display. Inductance formula of the proposed inductor structure was derived through magnetic circuit analysis for a simple inductance designing process. The proposed inductor was applied into a 1kW class interleaved bridgeless power factor correction circuit which requires four inductors, and experimental steady state result of the circuit was compared. According to the experimental result, it was found that the proposed multiple coupling inductor shows the electrical characteristics that can replace the conventional separated inductors and is suitable for miniaturization of the SMPS since the circuit configuration is possible with one shared inductor.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.857-859
• /
• 2002

This paper describes an analysis of Magnetic actuator with permanent magnet using 2-D axisymmetric finite element method. Magnetic actuator is the machine to change electrical signal into mechanical signal, and fast switching device to be used for breaker and automation field etc. This magnetic actuator considered action for armature distance, external circuit, and nonlinear material characteristic and current. Also, comparative analysis is performed for 2 coil type and 1 coil type by coil type of actuator, then characteristic is grasped. It is Combined with external circuit for analyzing transient characteristic by variable time. According to the results, we analyzed action characteristic of Magnetic actuator.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.7
• /
• pp.1231-1235
• /
• 2007

This paper presents the dynamic characteristics of a linear brushless dc (BLDC) motor with permanent magnet excitation for the precision conveyor according to the load condition. Dynamic performance of the linear BLDC motor driven with 6 step inverter such as thrust force and speed is simulated by finite element method coupling with external circuit and measured for the prototype motor. The results of finite element analysis are compared to the experimental results and verify reliability.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.35-42
• /
• 2003

Differential signaling has become a popular choice for high-speed interconnection schemes on Printed Circuit Boards (PCBs), offering superior immunity to external noise. However, conventional differential transmission lines on PCBs have problems, such as crosstalk and radiated emission. To overcome these, we propose a Twisted Differential Line (TDL) structure on a multi-layer PCB. Its improved immunity to crosstalk noise and the reduced radiated emission has been successfully demonstrated by measurement. The proposed structure is proven to transmit 3 Gbps digital signals with a clear eye-pattern. Furthermore, it is subject to much less crosstalk noise and achieves a 13 dB suppression of radiated emission. Index Terms - Twisted Differential Line, Differential Signaling, Crosstalk, Radiated Emission, Transmission Line, Twisted Pair

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.4
• /
• pp.7-13
• /
• 2001

In this paper, the external-exciting electronic ballast for an 100[W] high pressure sodium lamp using full-bridge inviter is designed. The L-C parallel full-bridge invert circuit for P-SPICE simulation is designed. The values of inductor and capacitor in the proposed equivalent L-C parallel resonant tank circuit are calculated theoretically. Then the ballast for high pressure sodium lamp is implemented using the simulated results. In the experimental results, that is confirmed which the results of implemented ballast are really same with the of simulated one.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.608-610
• /
• 2000

The static characteristic of a piezoelectric beam is for finding resonance frequency of the beam. In practice, it is required to analyze the beam with external command circuit including capacitors, inductors, and resistors for control. It means that the proper analysis of a piezoelectric beam with external command circuit is required by a dynamic analysis. We can also got transient and steady-state solution from the analysis. In this paper, the static and dynamic characteristic of the piezoelectric beam using FEM(Finite Element Method) are proposed.